Forum: 2003-04 Mach 1 - For Sale/Wanted
09-25-2014, 11:35 AM
|
Replies: 1
Views: 995
|
Forum: Insurance, Warranties and License Info
08-13-2014, 08:28 AM
|
Replies: 75
Views: 32,258
|
Forum: Brakes & Suspension
08-12-2014, 07:46 AM
|
Replies: 5
Views: 851
|
Forum: Mustangs Parts For Sale/Wanted
08-11-2014, 02:41 PM
|
Replies: 4
Views: 878
|
Forum: NEW Mach 1 Owner Introductions
07-12-2014, 11:11 PM
|
Replies: 15
Views: 1,352
|
Forum: Mustangs Parts For Sale/Wanted
07-03-2014, 10:38 AM
|
Replies: 8
Views: 1,290
|
Forum: Mustangs Parts For Sale/Wanted
06-29-2014, 09:44 AM
|
Replies: 8
Views: 1,290
|
Forum: Engine & Drivetrain (Including trans & rear axles)
06-26-2014, 01:33 PM
|
Replies: 10
Views: 1,332
Re: Oil Pump Gear
If you are reading that based on my thread, for the record, I have hit the rev limiter 3 times total that I owned the car (420 miles). Hard to say if that was the cause or not, but its the only...
|
Forum: Mustangs Parts For Sale/Wanted
06-21-2014, 07:50 PM
|
Replies: 8
Views: 1,290
|
Forum: Mustangs Parts For Sale/Wanted
06-19-2014, 10:37 PM
|
Replies: 0
Views: 1,250
|
Forum: Power Adders
06-19-2014, 08:02 AM
|
Replies: 9
Views: 1,743
Re: Cobra timing cover leaking
Next time, use this stuff:
http://www.amazonsupply.com/permatex-29208-6pk-right-stuff-gasket/dp/B001REYVJE
Right Stuff Gasket maker.
You could have used that without pulling the cover.
|
Forum: Tuning & Dyno Testing/Results
06-17-2014, 07:48 AM
|
Replies: 37
Views: 4,084
Re: Well, got back from the dyno....
It wasnt 14.67, that just the peak of the reading as it starts recording. It was in the mid 11's the entire pull.
Not like it matters now anyway...
|
Forum: General Registry Discussion
06-16-2014, 09:08 AM
|
Replies: 13
Views: 1,390
|
Forum: General Registry Discussion
06-15-2014, 09:47 PM
|
Replies: 13
Views: 1,390
|
Forum: Tuning & Dyno Testing/Results
06-13-2014, 10:11 AM
|
Replies: 37
Views: 4,084
|
Forum: Tuning & Dyno Testing/Results
06-13-2014, 09:24 AM
|
Replies: 37
Views: 4,084
Re: Well, got back from the dyno....
So went yesterday and got the new pulley on and re-dynoed. Results were a bit better. 432/368 at 7 PSI. I am a lot happier with that. IAT's were in the mid 160's throughout the day, about what...
|
Forum: Tuning & Dyno Testing/Results
06-04-2014, 02:37 PM
|
Replies: 37
Views: 4,084
|
Forum: Power Adders
06-03-2014, 02:19 PM
|
Replies: 12
Views: 2,046
Re: How to extend ps hose line?
No, it was just standard braided line from Jegs:
http://www.jegs.com/i/JEGS+Performance+Products/555/100920/10002/-1
But Id not feel conforable using a hose clamp keeping it together at those...
|
Forum: Tuning & Dyno Testing/Results
06-03-2014, 02:16 PM
|
Replies: 37
Views: 4,084
Re: Well, got back from the dyno....
Got the new intake on. I can actually hear the blower a little bit more, so I think its a step in the right direction. We got a 3" pulley and the tuner said it should be good for 7 psi. Going back...
|
Forum: Power Adders
06-03-2014, 07:54 AM
|
Replies: 12
Views: 2,046
Re: How to extend ps hose line?
This is what I did when I did the Hydroboost conversion on my old turbo fox. Pretty sure this is what I used:
http://www.jegs.com/i/Russell/799/632610/10002/-1
...
|