|
|
2003-04 Mach 1 - For Sale/Wanted Post ONLY 03-04 Mach 1s For sale or wanted. Please Put Year, Color & Location in title! |
|
Thread Tools | Display Modes |
06-22-2007, 05:13 PM | #1 |
Registered User
Join Date: Mar 2005
Posts: 306
|
525 rwhp 03 mach1 for sale connecticut
2003 Azure Blue 6spd IUP
21,000 miles. This car has been completely modded and is a scary fast steet car. I have spared no expense with the parts put into this car. Here's the skinny: I removed the motor and had the engine forged because I wanted it done right. There wasnt any problems with the engine when I removed it but I didnt want to take any chances with the supercharger. It has mahle lc forged pistons, forged rods and since this car was originally auto the crank was also forged. I had a hi flow oil pickup and billet gears put in. The compression ratio is 9:1. Comp Cams stage 2 blower cams were also installed The auto tranny was yanked and in went a brand new cobra spec T56 6 spd. I have a pro 5.0 shifter, aluminum driveshaft, McLeoud clutch, fidenza alum flywheel. I have a procharger p1sc supercharger on the car. It currently is maxing out at 9lbs of boost with no belt slip. The rear end was just upgraded in the fall. The gears are 410's and it has 31 spline auburn hi-po posi with moser axles. I also installed che upper and lower control arms and pumpkin brace. As far as other performance parts on the car their is the Granatelli coil packs and wires, x-cal 2 (custom tune obviously), 03/04 cobra tank fuel pumps and a KB boost-a-pump. 42lb injectors, slp catted x pipe, slp cat back with power flo mufflers. Cosmetically the car has 03/04 cobra front bumper and a carbon fiber hood that it particially painted (see pics) The rear bumper is painted black in the little recess between the exhast tips. Also has boost and fuel pressure guages on the pillar. Paint is very good except for the deck lid. Which got keyed this summer. The car has brand new perelli p zero's on all four. I'm sure I left alot out I'm trying to remember everything I've done and there has been so much lol. At the dyno in May the car made 525 rwhp and 465 rwtq. This was on a mustang dyno. That is with only 9lbs of boost and a conservative tune. As far as driving this car. At any point in first gear if you mash the gas it will light up the tires, On to 2nd gear if you powershift it the tires will break completely loose and spin untill you get off the gas if you shift it easy and mash the gas it will start to break the tire loose at about 5000 rpms and you'll have to get off it or shift to 3rd. With 3rd gear if you get a good shift the tires will again brake loose but a quick pedal will plant em for good. The thing I like about having the cetrifical s/c is that up to about 3500 ish rpm the car is relatively tame. If anyone has any questions please pm me or feel free to call me at 203-266-5481 or 203-560-7664 --Thanks $19,000.00 obo Here is the linky for pics http://www.mach1registry.org/forums/...ad.php?t=48960
__________________
03 Azure Blue Mach 1 Forged short block 9:1 compression, Procharger p1sc #12, Comp cams stage 2 blower cams, Mcleod Clutch, fidenza aluminum flywheel, T-56 tranny, pro 5.0 shifter, Aliminum driveshaft, Slp x-pipe, slp lm2's, cobra tank and pumps, KB Bap, Carbon fiber hood (painted), 03/04 cobra front bumper. Auburn pro 31 spline diff, moser axles, che upper + lower control arms, che axle brace, 410's 525rwhp 465 rwtq Mustang dyno |
06-22-2007, 11:31 PM | #2 |
What a ride it was :)
Join Date: Aug 2002
Location: TX
Posts: 4,489
|
Re: 525 rwhp 03 mach1 for sale connecticut
I wish it was time for me to have another toy. I would be all over this deal.
Bump for ya
__________________
No, I didn't do that! Wait maybe I did! |
06-23-2007, 11:56 AM | #3 |
Registered User
Join Date: May 2007
Location: Bristol, CT
Posts: 6
|
Re: 525 rwhp 03 mach1 for sale connecticut
Sent a PM to you, Thanks Kyle
|
06-24-2007, 08:49 AM | #4 |
Registered User
Join Date: Nov 2006
Location: Woodlands, TX
Posts: 205
|
Re: 525 rwhp 03 mach1 for sale connecticut
Nice ride good luck on the sale!
|
06-24-2007, 12:36 PM | #5 |
Registered User
Join Date: Mar 2005
Posts: 306
|
Re: 525 rwhp 03 mach1 for sale connecticut
Thanks hopefully it sells soon. Someone is going to get a hell of a deal, and have a scary fast car.
__________________
03 Azure Blue Mach 1 Forged short block 9:1 compression, Procharger p1sc #12, Comp cams stage 2 blower cams, Mcleod Clutch, fidenza aluminum flywheel, T-56 tranny, pro 5.0 shifter, Aliminum driveshaft, Slp x-pipe, slp lm2's, cobra tank and pumps, KB Bap, Carbon fiber hood (painted), 03/04 cobra front bumper. Auburn pro 31 spline diff, moser axles, che upper + lower control arms, che axle brace, 410's 525rwhp 465 rwtq Mustang dyno |
06-24-2007, 11:59 PM | #6 |
Registered User
Join Date: Apr 2004
Location: Manassas, Va
Posts: 314
|
Re: 525 rwhp 03 mach1 for sale connecticut
where are you located? Any oil in the intake tract? I know those p1sc are prone to leak.
|
06-25-2007, 10:41 PM | #7 |
Registered User
Join Date: Mar 2005
Posts: 306
|
Re: 525 rwhp 03 mach1 for sale connecticut
I am located in connecticut and NO the p1sc doesnt leak oil into the intake. I have had the blower on for 9,000 miles and hasnt leaked at all. I always check the level regularly!!! My personal exp. says that is a myth that happened to a couple blowers and thats all anyone talks about
__________________
03 Azure Blue Mach 1 Forged short block 9:1 compression, Procharger p1sc #12, Comp cams stage 2 blower cams, Mcleod Clutch, fidenza aluminum flywheel, T-56 tranny, pro 5.0 shifter, Aliminum driveshaft, Slp x-pipe, slp lm2's, cobra tank and pumps, KB Bap, Carbon fiber hood (painted), 03/04 cobra front bumper. Auburn pro 31 spline diff, moser axles, che upper + lower control arms, che axle brace, 410's 525rwhp 465 rwtq Mustang dyno |
06-26-2007, 08:10 PM | #8 |
Registered User
Join Date: Mar 2005
Posts: 306
|
Re: 525 rwhp 03 mach1 for sale connecticut
Sold!!!
__________________
03 Azure Blue Mach 1 Forged short block 9:1 compression, Procharger p1sc #12, Comp cams stage 2 blower cams, Mcleod Clutch, fidenza aluminum flywheel, T-56 tranny, pro 5.0 shifter, Aliminum driveshaft, Slp x-pipe, slp lm2's, cobra tank and pumps, KB Bap, Carbon fiber hood (painted), 03/04 cobra front bumper. Auburn pro 31 spline diff, moser axles, che upper + lower control arms, che axle brace, 410's 525rwhp 465 rwtq Mustang dyno |
06-26-2007, 08:20 PM | #9 |
Eaton swapped User
Join Date: Dec 2005
Location: Austin, TX
Posts: 771
|
Re: 525 rwhp 03 mach1 for sale connecticut
Wow, that was a crazy cheap price! That's not much more than a relatively stock Mach 1. Someone got a hell of a deal.
|
07-03-2007, 07:01 PM | #10 |
Registered User
Join Date: Jul 2007
Location: Bristol ct
Posts: 45
|
Re: 525 rwhp 03 mach1 for sale connecticut
just picked this beast up yesterday. bad *** car i must say.
|
07-03-2007, 07:07 PM | #11 |
Registered User
Join Date: Jun 2004
Location: Madera, CA
Posts: 7,687
|
Re: 525 rwhp 03 mach1 for sale connecticut
CONGRATS....Bills car was a great one...you are lucky.
__________________
Current Stable: NO stangs.....DON'T F'ING remind me. Previous stangs: 2003 Mineral Grey Cobra Vert 1965 Factory GT K Code Coupe - mostly original and numbers matching. 14.9 (best) GONE BUT NOT FORGOTTEN!! 2003 MACh 1 AB - MINE!..SLP LM1s, PHP Spacer, and a CAI, that wont' stop whistling. 2004 MACh 1 DSG - PHP spacer, BOrla Stingers, K and N CAI, Tune, X-pipe, 1" 1-piece raised shaker...yadda yadda. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|