|
02-16-2010, 07:13 PM | #1 |
Registered User
Join Date: Dec 2007
Location: St. Louis, Missouri
Posts: 358
|
cobra cam install
hey just ordered some 98 cobra intake cams. Are there any tips or tricks that will make the install somewhat easier any other parts that I should buy??? How do I degree the cams and how much should I degree them for best output???
__________________
Pierre; United States Air Force Mach1 2004 Azure Blue Mach1 MODS BBK LT BBK off-road H-pipe 4.10s 31spline diff and axles Magnapack catback JLT rai PHP 3/8 spacer Accufab Throttle Body Lighting 90mm MAF Steeda Tri-ax 39lb injectors 98 cobra intake cams SCT X-Cal 3 custom dyno tune by Mustang Muscle |
02-17-2010, 05:49 PM | #2 |
Registered User
Join Date: Dec 2007
Location: St. Louis, Missouri
Posts: 358
|
Re: cobra cam install
anyone
__________________
Pierre; United States Air Force Mach1 2004 Azure Blue Mach1 MODS BBK LT BBK off-road H-pipe 4.10s 31spline diff and axles Magnapack catback JLT rai PHP 3/8 spacer Accufab Throttle Body Lighting 90mm MAF Steeda Tri-ax 39lb injectors 98 cobra intake cams SCT X-Cal 3 custom dyno tune by Mustang Muscle |
02-17-2010, 05:51 PM | #3 |
Its stock....No really!
Join Date: Jul 2005
Location: Albuquerque, NM
Posts: 4,433
|
Re: cobra cam install
__________________
2003 Azure Blue Mach 1 5spd w/ IUP Mods: Lots of new stuff coming.....stay tuned |
02-18-2010, 10:35 AM | #4 |
Registered User
Join Date: Dec 2003
Location: Friendswood, tx
Posts: 531
|
Re: cobra cam install
I'm about to do the same next weekend. i did a search and it seems easy on here. but other people are telling me its hard and the timing cover has to come off and all kinds of stuff. I'm not planning on degreeing it if i dont have to.
i want to have everything ready before i start. like gaskets and stuff.
__________________
old 2003 Black Mach-1 Best 12.460 @ 110.15 60' 1.782 new 03 Black Mach-1 |
02-18-2010, 11:34 AM | #5 | |
Registered User
Join Date: Dec 2007
Location: beavercreek, oh
Posts: 4,695
|
Re: cobra cam install
Quote:
|
|
02-18-2010, 01:26 PM | #6 | |
Registered User
Join Date: Dec 2006
Location: Calgary AB
Posts: 229
|
Re: cobra cam install
Quote:
When we did my brothers there is upwards of 4-6 degrees of deadband swing from the chains and slop in them. With that said 4-6 degrees just in that and not even accounting for where you install the cams you could be way out and leave plenty of power behind that is needlessly left out. Even if it takes 2 days to figure out and degree them properly is worth it in the end.
__________________
04 Cobra 3.4 Whipple, return fuel, ARH headers, etc. 11.6 @ 133.8mph, 2.05 60', 5200ft DA, 275/40/17 M/T radials. |
|
02-18-2010, 06:17 PM | #7 |
Registered User
Join Date: Dec 2003
Location: Friendswood, tx
Posts: 531
|
Re: cobra cam install
well back to the drawing board lol
__________________
old 2003 Black Mach-1 Best 12.460 @ 110.15 60' 1.782 new 03 Black Mach-1 |
02-22-2010, 02:11 PM | #8 |
Registered User
Join Date: Dec 2003
Location: Friendswood, tx
Posts: 531
|
Re: cobra cam install
so is ths kit all i will need to degree them?
http://www.atlanticspeed.com/product...idproduct=1515 is there a cam lock tool that is needed?
__________________
old 2003 Black Mach-1 Best 12.460 @ 110.15 60' 1.782 new 03 Black Mach-1 |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|