|
04-06-2017, 11:01 AM | #201 |
Registered User
Join Date: Jun 2015
Location: erie Pa
Posts: 110
|
Re: Starting my Build
I will ask this here?
Is it worth putting 4.11 gears in this car stock? |
05-16-2017, 12:31 AM | #202 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
Ok guys I'll be swapping to the F1-A soon Only thing is I have to get it painted, the previous owner had it powder coated yellow. I'm thinking of either powder coating it azure or hydro dipping it in Carbon fiber. What would you do???
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
05-16-2017, 02:42 PM | #203 |
finally paid for
Join Date: Nov 2004
Location: Ypsilanti Twp, Mi
Posts: 4,077
|
Re: Starting my Build
hydro dipping is very cool...
__________________
2004 mach 1-turbo build in progress.. Fast xfi 2.0 OLD combo- 826rwhp/720 trq -100 shot NX 9.13@154 on 100 shot NEW- in progress... |
05-18-2017, 11:33 PM | #204 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
I dropped off the head unit earlier today to get dipped. Now Im looking to upgrade my BOV. Im not too sure which one to go with just yet, I need something that's good for 18 to 20 psi.
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
05-19-2017, 12:03 AM | #205 |
Registered User
Join Date: Jan 2013
Location: San Diego, CA
Posts: 1,104
|
I ran a Tial 50mm with my F1A. It was pullied for 19psi and it wasn't quiet.
Sent from my SAMSUNG-SM-G935A using Tapatalk
__________________
New Ride: 2004 Mystichrome Cobra-Accufab SBTB and plenum, Steeda 2.8" upper, Bassani X, Borla Stingers, Mcleod RXT, MGW shifter, Level 5 halfshafts, chrome FR500's, Stiffler's FIT system and DS safety loop, GT pumps, BA3000, tuned by owner |
05-19-2017, 12:51 PM | #206 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
Im looking for something a bit more quiet, definitely staying away from the BBRV. I was thinking of vortech race valve but I'm not too sure if it will be enough for the F1. I got to do some research.
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
05-19-2017, 01:30 PM | #207 |
finally paid for
Join Date: Nov 2004
Location: Ypsilanti Twp, Mi
Posts: 4,077
|
Re: Starting my Build
the F1 itself isn't quiet...you wont be feeling anyone...lol
__________________
2004 mach 1-turbo build in progress.. Fast xfi 2.0 OLD combo- 826rwhp/720 trq -100 shot NX 9.13@154 on 100 shot NEW- in progress... |
05-19-2017, 06:47 PM | #208 |
Registered User
Join Date: Jan 2013
Location: San Diego, CA
Posts: 1,104
|
What he said. One time driving home my discharge pipe popped off the blower. I was blow through so the car still ran fine. At that point I didn't have any noise from the BOV, just the blower. It was still pretty loud. My friends used to joke that if you wanted a different noise to switch the side of the car they were driving by. Driver side was the BOV and passenger side was the blower.
Sent from my SAMSUNG-SM-G935A using Tapatalk
__________________
New Ride: 2004 Mystichrome Cobra-Accufab SBTB and plenum, Steeda 2.8" upper, Bassani X, Borla Stingers, Mcleod RXT, MGW shifter, Level 5 halfshafts, chrome FR500's, Stiffler's FIT system and DS safety loop, GT pumps, BA3000, tuned by owner |
05-21-2017, 11:48 PM | #209 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
Which gears did you guys use with the F1? I'm on 4:10s now and I was thinking of switching to 3:55.
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
09-01-2017, 08:02 PM | #210 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
I went ahead and slapped on the F1a and as you guys mentioned it's LOUD! Probably a bit to much for me honestly. I just might get rid of after I hurt some feelings or maybe downgrade to a D1SC. I'll post a pick soon it looks Good dipped in the carbon fiber.
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
09-01-2017, 09:31 PM | #211 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Starting my Build
the D1X has my attention
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
09-01-2017, 10:09 PM | #212 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
is that bigger than the F-1a? What's the difference between that one and the d1sc? with my high compression ratio I think the F1 is just too much.
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
09-01-2017, 10:30 PM | #213 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Starting my Build
they now have a p1x and a D1x, not sure exactly whats different but both are apparently far more efficient than there non "x" counterparts. A D1 at lower boost levels is supposedly good for 30ish more hp same pullies and higher boost closer to 100 more hp, same pullies.
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
09-03-2017, 04:25 AM | #214 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
waiting on a new bov, intercooler and 3.55 gears then it will be headed to the dyno
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
10-01-2017, 10:04 PM | #215 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
Picked up an 01 Cobra bumper couple months back. Decided to put it on while I was switching to the tr259 intercooler
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
10-02-2017, 08:35 AM | #216 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Starting my Build
love the way those look
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
10-03-2017, 05:31 PM | #217 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
Thanks. just waiting on some fog light bezels and I'll be using 03 Cobra fog lights.
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
10-03-2017, 09:38 PM | #218 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Starting my Build
Ya I just took my bumper apart to have the tabs and such fixed. I’ll be going 03/04 fogs as well. Found a great write up on svtp. Probably gonna go HID fogs and retrofit headlights as well
...and eat top ramen for a bit lol
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
10-04-2017, 06:36 PM | #219 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
Haha top ramen and Lunchables is all the pockets allow. Glad to say im almost done with this build finally. I'd like to go with retrofits but they're a bit too pricey for me. Care to share that link on install installing the fogs?
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
10-04-2017, 09:47 PM | #220 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Starting my Build
I’m gonna have to find it again, it didn’t save it to my watches threads apparently
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
10-04-2017, 09:49 PM | #221 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Starting my Build
Never mind, just too dumb to realize how that worked
https://www.svtperformance.com/forum...ersion.861320/
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
11-13-2017, 08:46 PM | #222 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Starting my Build
took the Mach out to the track with the new setup and ran 10.66 at 138 mph. It gained 13 miles per hour from the Old set up with a P1.
had some traction issues but I'll be back soon im sure it'll do low tens. I'll post a video soon
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
11-14-2017, 12:47 PM | #223 |
Registered User
Join Date: Mar 2017
Location: Tucson, Az
Posts: 160
|
Re: Starting my Build
Nice pick up.
__________________
1st: 1998 v6 2nd: 2000 GT Current: 2003 Mach 1 |
11-14-2017, 02:34 PM | #224 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Starting my Build
congrats, thats a nice gain!
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
11-14-2017, 09:46 PM | #225 |
Can't be bridled
Join Date: Sep 2007
Location: Texas
Posts: 7,006
|
Re: Starting my Build
that's moving...
__________________
2004 Mach 1 #6956 5spd w/IUP Eaton swap, longtubes, built 3.73 SRA 452hp/409tq dynojet🏁 |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|