|
|
Power Adders Superchargers, Turbos, Nitrous, etc... |
|
Thread Tools | Display Modes |
04-05-2016, 10:11 PM | #1 |
Registered User
Join Date: May 2011
Location: sc
Posts: 135
|
Kooks longtubes gains on my cammed mach 1
finally added some Kooks Longtubes headers and off road Kooks xpipe to my mach 1.
old setup was custom cams, JLT CAI, stock Headers, magnaflow catted xpipe, borla stingers, and lightweight spec aluminum flywheels. New Setup; custom cams, JLT CAI,Kooks 1 5/8 longtubes with Kooks 2 1/2 offroad xpipe, borla stingers,lightweight spec aluminum flywheels and weld rts wheels. Dyno run. https://youtu.be/scFIou9f2MM At pro dyno, some kooks goddies DSC_0003 by mr proper, on Flickr crazy, k member removal for longtubes. DSC_0008 by mr proper, on Flickr on the dyno... you will be surpised! DSC_0013 by mr proper, on Flickr |
04-05-2016, 10:16 PM | #2 |
Registered User
Join Date: May 2011
Location: sc
Posts: 135
|
Re: Kooks longtubes gains on my cammed mach 1
old dyno sheet with custom cams, jlt cai, stock headers, magnaflow catted xpipe, borla and afs 10.5 rear wheels.
Untitled by mr proper, on Flickr same setup as on fastlane dyno but retuned at pro dyno. Untitled by mr proper, on Flickr finall dyno numbers on same dyno after adding Kooks longtubes, offroad xpipe and weld rts wheels! 374 rwhp and 364rwtq!!!!!! Untitled by mr proper, on Flickr old setup with new setup comparison Untitled by mr proper, on Flickr |
04-05-2016, 10:41 PM | #3 |
Registered User
Join Date: Jan 2008
Location: Kyle, Texas
Posts: 2,285
|
Re: Kooks longtubes gains on my cammed mach 1
Nice!! Sick car man, I miss my old cammed Mach from time to time!
__________________
**SOLD**04' Mach 1 -Comp Cams 106100's (deg 106/110) -Eatonswap with 3.4 Pulley -Full Exhaust (mac lts & xpipe, sss terminator c/b) -Built Rear w/ 3.55 gears [B]-Tuned by Lethal Performance of San Antonio -510hp/478tq |
04-05-2016, 10:48 PM | #4 |
Registered User
Join Date: May 2011
Location: sc
Posts: 135
|
Re: Kooks longtubes gains on my cammed mach 1
|
04-06-2016, 12:00 AM | #5 |
Registered User
Join Date: Jan 2008
Location: Kyle, Texas
Posts: 2,285
|
Re: Kooks longtubes gains on my cammed mach 1
Lol! Yea I watch them at least twice a week...haha
__________________
**SOLD**04' Mach 1 -Comp Cams 106100's (deg 106/110) -Eatonswap with 3.4 Pulley -Full Exhaust (mac lts & xpipe, sss terminator c/b) -Built Rear w/ 3.55 gears [B]-Tuned by Lethal Performance of San Antonio -510hp/478tq |
04-06-2016, 06:51 AM | #6 |
it's soo-tack
Join Date: Nov 2002
Location: Fairmont, WV
Posts: 2,082
|
Re: Kooks longtubes gains on my cammed mach 1
Very nice
__________________
mark 2004 DSG Mach 1. Built motor. Turbo. 667whp 2006 Sonic Blue Focus. Built motor. Turbo. 12.4 @ 115mph (sold) 2003 DSG Mach 1. 12.65 @ 106 (sold) |
04-06-2016, 06:59 AM | #7 |
Registered User
Join Date: Dec 2015
Location: Selden, NY
Posts: 96
|
Re: Kooks longtubes gains on my cammed mach 1
AWESOME RESULTS
__________________
04 Mach 1, Aluminum 4.6L DOHC w/Procharger P1SC & Stage II 3 Core Intercooler Level 10 4R70W, Convertor, 8.8 w/3.5 Posi, Snow Perf Stage 2 Methanol Injection |
04-06-2016, 07:04 AM | #8 |
Can't be bridled
Join Date: Sep 2007
Location: Texas
Posts: 7,006
|
Re: Kooks longtubes gains on my cammed mach 1
And it'll feel like even more of a gain than it shows on paper! I remember going from stock manifolds and catted x to longtubes and offroad x, untuned, and it felt like 40-50hp. On a cammed mach, I bet it feels like 75.
Congrats
__________________
2004 Mach 1 #6956 5spd w/IUP Eaton swap, longtubes, built 3.73 SRA 452hp/409tq dynojet🏁 |
04-06-2016, 08:44 AM | #9 |
Registered User
Join Date: Dec 2010
Location: Jackson, TN
Posts: 308
|
Re: Kooks longtubes gains on my cammed mach 1
40hp and 33tq those are very nice gains!
__________________
2003 Mach 1 Aluminator // Eaton @ 10lbs // T56 Magnum // E85 Build thread: http://www.svtperformance.com/forums...-Picture-Heavy IG: boostedmach |
04-06-2016, 08:51 AM | #10 |
Registered User
Join Date: Nov 2011
Location: Jersey
Posts: 442
|
Re: Kooks longtubes gains on my cammed mach 1
What kind of cams are those? I know it says custom but they seem to do very well for you
__________________
03 Mach 1 JLT Next Gen CAI (fenderwell), VAP 5/8 Plenum Spacer, 10" Ported Short Runner Intake (Roy), Bassani Mid Length Headers, Bassani O/R X Pipe, Mac 3" Catback, March Fluid Dampener, Hydro-boost and WP Pulleys, FRPP Aluminum DS, Ported Throttle Body, 4.10 Gears, 315/35/17's Tuned by Wicked Motorsports |
04-06-2016, 10:39 AM | #11 |
Registered User
Join Date: May 2011
Location: sc
Posts: 135
|
Re: Kooks longtubes gains on my cammed mach 1
|
04-06-2016, 10:44 AM | #12 |
Registered User
Join Date: Nov 2011
Location: Jersey
Posts: 442
|
Re: Kooks longtubes gains on my cammed mach 1
Impressive
__________________
03 Mach 1 JLT Next Gen CAI (fenderwell), VAP 5/8 Plenum Spacer, 10" Ported Short Runner Intake (Roy), Bassani Mid Length Headers, Bassani O/R X Pipe, Mac 3" Catback, March Fluid Dampener, Hydro-boost and WP Pulleys, FRPP Aluminum DS, Ported Throttle Body, 4.10 Gears, 315/35/17's Tuned by Wicked Motorsports |
04-06-2016, 12:38 PM | #13 |
Lorraine's driver
Join Date: Apr 2012
Location: Indianapolis, IN
Posts: 2,442
|
Re: Kooks longtubes gains on my cammed mach 1
That's excellent!!
__________________
|
04-06-2016, 05:56 PM | #14 |
Dark Knight
Join Date: Nov 2009
Location: Albuquerque, NM
Posts: 5,759
|
Impressive. I wonder if going from catted to catless made a big difference too. That thing is a short runner away from knocking at 400 to the tire.
__________________
Vortech V2 S-trim, E85, A2A Treadstone, Comp cams, built engine, full exhaust, built rear, built 4r70, more mods. Tuned by me with SCT Advantage |
04-06-2016, 06:20 PM | #15 | |
Registered User
Join Date: May 2011
Location: sc
Posts: 135
|
Re: Kooks longtubes gains on my cammed mach 1
Quote:
Also the rotten egg smell at idle is gone since going catless. |
|
04-06-2016, 06:53 PM | #16 |
SVT
Join Date: Jun 2010
Location: Northern California
Posts: 812
|
Re: Kooks longtubes gains on my cammed mach 1
Very Nice!..good #'s for basically just Longtubes and cams
Your car looks amazing on those RTS wheels
__________________
2001 Zinc yellow SVT Cobra Forged 11.5CR 284ci Comp 106500 cams - Degreed 01 cobra Heads - tastefully modded Roys ported/polished Intake Kooks longtubes, Magnaflow catback D&D T3650, Mgw shifted FTB Goodies, 4.30s, FRPP diff cover, 31 splined IRS 04 cobra interior , black termy seats, Speedhut gauges Tubular K, MM coilovers/ Koni SA yellows Starkweather tuned, 24* timing on 91 octane 11.7 @ 117mph 1.62 60ft. Raceweight 3200lbs Next up:Sullivan intake and hat, self tuning.. |
04-06-2016, 10:30 PM | #17 |
Registered User
Join Date: May 2011
Location: sc
Posts: 135
|
Re: Kooks longtubes gains on my cammed mach 1
here is the idle video,
cold start, idle drops down to about after 30sec to about 1200rpm (warm idle is 900rpm), throttle blip is only up to 2000rpm (engine still cold). enjoy https://www.youtube.com/watch?v=zB7K...ature=youtu.be |
04-07-2016, 07:37 AM | #18 |
Registered User
Join Date: Nov 2011
Location: Jersey
Posts: 442
|
Re: Kooks longtubes gains on my cammed mach 1
wow sounds really good actually, not as heavy of a lope as i imagined but a really nice idle sound.
__________________
03 Mach 1 JLT Next Gen CAI (fenderwell), VAP 5/8 Plenum Spacer, 10" Ported Short Runner Intake (Roy), Bassani Mid Length Headers, Bassani O/R X Pipe, Mac 3" Catback, March Fluid Dampener, Hydro-boost and WP Pulleys, FRPP Aluminum DS, Ported Throttle Body, 4.10 Gears, 315/35/17's Tuned by Wicked Motorsports |
04-07-2016, 09:56 AM | #19 |
Registered User
Join Date: May 2011
Location: sc
Posts: 135
|
Re: Kooks longtubes gains on my cammed mach 1
|
04-07-2016, 02:50 PM | #20 |
Registered User
Join Date: Oct 2013
Location: Attalla Alabama
Posts: 130
|
Re: Kooks longtubes gains on my cammed mach 1
I really want to put a set of cams in mine. That car is beautiful man, and sounds great. Do you plane to take it to the track at all?
|
04-07-2016, 05:58 PM | #21 |
Never Satisfied
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
|
Re: Kooks longtubes gains on my cammed mach 1
awesome numbers.
__________________
P1 8psi @ 6k PA Transmission DD 3,600 Stall BBK LT's w/ 3in Collector Custom 3in X-Pipe Custom 3in CB w/ Pypes 3in M-80's Built Rear w/ 4:10 415/383 PB 11.80, @ 119 with a 1.71 60ft Tuned by http://www.southtexasperformance.com/ Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon. |
04-08-2016, 08:32 AM | #22 |
Registered User
Join Date: Aug 2007
Location: Fredericksburg, VA
Posts: 392
|
Re: Kooks longtubes gains on my cammed mach 1
congrats on the gains, very impressive numbers. I bet that thing sounds mean as hell now!
__________________
2004 DSG Mach 1 476rwhp and 406rwtq at 8lb Kenne Bell 2.1 blower comp cams 106100 LTs, Prochamber, catback built rear with 4.30s accufab TB, alum ds, Roush shifter AFS wheels, Nitto tires, Eibach springs |
04-08-2016, 09:35 AM | #23 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Kooks longtubes gains on my cammed mach 1
thats awesome, I never would have guessed those kinds of gains!
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
04-09-2016, 08:00 AM | #24 |
Registered User
Join Date: May 2011
Location: sc
Posts: 135
|
Re: Kooks longtubes gains on my cammed mach 1
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|