- A few mods planned, could use some input.
- laptop
- Torque Mod.
- Steeda CAI Installed w/pics
- Need Help with CAI
- Lobe Separation
- Al (Boss 330 Racing) Contact info??
- Tell me your Tremec 3650 "Horror Stories"
- I`m installing
- For those with 4.30 gears...
- Shift Kit?
- If you have 4.30s...
- 4.10 Installed - Great choice
- Driveshaft options?
- Those of you wil 4.10's or taller gear
- Shaker Scoop a little too shaky?
- Just added a PHP intake spacer.
- Short-Throw Shifter Any Recommendations?
- Can't Believe this, I actually lost HP/TQ...
- K&N Charger Question
- Intake spacer??
- IAC Restrictor Plates - Order Page
- Up and Atom
- Wanted Polished Coil Covers
- PHP spacer on today
- How to remove factory rear-end??
- Rebuilding bottom end - have some questions
- link to tick '03-'04 video
- Good info on the FR500 Intake for the Mach
- Which firewall adjuster (links inside)?
- Sullivan 4.6DOHC Intake
- Has anyone installed a shift kit in their auto?
- ported 03/04 head LOTS OF pics BEWARE
- Let's talk rear ends..
- Dropped my car off @ HPP in Denton Sat.
- C&L Intake and Problems
- axles
- Surging at cruising rpms
- What's wrong with my Mach!?
- Axles Lengths??? PLEASE HELP
- Carb'd 4.6 in a Fox
- RPM Outlet "dyno-tuned" packages
- Models with a similar engine as the Mach1
- Parts to be isntalled (finally!)
- Quick question
- Port and polish job.
- Clutch question
- 450+ hp
- What would the cost be?
- '05 GT rear end fit on the mach?
- HP/TQ possibilities
- This Weekends Project...
- P0455 Code! Help :(
- LDC Chicago vs Apten Cooling Mod Kit
- Detroit Locker Install Requirements???
- FRPP Aluminum Transmission Pan Installed
- Starting to work on the Mach...some questions
- EVAP Vapor Management Valve
- IAC Restrictor plates
- Mach Cams
- which filter is it?
- Yet Another K&N Aircharger take...
- what do i need to do if I put 4.10's in?
- I want to find the nearest living thing and beat the hell out of it
- Fan on while car off
- My thoughts on the Tri-Ax install
- MRT Cold Air Box and ProM Air meter
- Beefing up rear axles?
- "squealing" noise shortly after spacer install
- Aluminum vs Steel Flywheel
- Wheel studs?
- K&N/Aftermarket Air Intake
- Which CAI and tuner
- Will a C&L CAI fit with the Steeda STB?
- Another Mach with new gears and axles.
- sparkplug?
- Part # for 4.10's Not FRPP
- Aluminum drive shaft
- trac loc and 3.73 in wilmington nc
- Advice on Mods
- What was the cooling system mod
- Jlt Cai/rai
- Gear Advice And Installation In Michigan?
- Anyone with similar mods as me with dyno numbers?
- Driveshaft whistle ?
- Accelerator sticking
- misfiring
- Steeda pulleys and 180 stat
- Auto Trans Help w/ Valve Body Selection
- What is the most power a Mach can produce?
- Need Help Fast!!!
- Air Silencer/milk jug
- 5.0 Cammer in Mach
- Need some input on what to get here
- Where's the cheapest place to buy 4.10s and whatever else I need?
- Did C&L Want you to do this?
- This C&L system and dealer ok?
- HPP Stands For High Power Performance
- Looking to purchase a UPR clutch quadrant, firewall adjuster, and adjustable cable..
- Varying Idle RPM's