2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Electrical System

Reply
 
Thread Tools Display Modes
Old 05-02-2018, 09:02 PM   #1
crazyone64
Registered User
 
Join Date: Apr 2008
Location: Toronto
Posts: 16
Power Window acting up

Hi

I was hoping to get some advice while I present some observations with my Power Window issue:

2003 Mach 1
Drivers side power window is stuck in the closed position.
It was intermittent for a few years and now fully stuck, closed.
When pressing the drivers side power window button, i can hear a click from within the door. There is no window movement or motor sound/grinding.
When pressing the drivers side power window button that controls the passenger window, works perfectly. Never was an issue.

Since i hear a click from within the door, i believe this eliminates the power window switch as it is sending power to the regulator. Beyond this I am confused.

Any advice?
Thanks!
crazyone64 is offline   Reply With Quote
Old 05-02-2018, 09:05 PM   #2
01yellerCobra
Registered User
 
Join Date: Jan 2013
Location: San Diego, CA
Posts: 1,104
Sounds like the window motor finally died completely to me.
__________________
New Ride:
2004 Mystichrome Cobra-Accufab SBTB and plenum, Steeda 2.8" upper, Bassani X, Borla Stingers, Mcleod RXT, MGW shifter, Level 5 halfshafts, chrome FR500's, Stiffler's FIT system and DS safety loop, GT pumps, BA3000, tuned by owner
01yellerCobra is offline   Reply With Quote
Old 05-02-2018, 09:25 PM   #3
DSG2003Mach1
700 HP Mach
 
DSG2003Mach1's Avatar
 
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
Re: Power Window acting up

Ya probably a dead motor
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc...

'12 F150 FX2 Supercrew with Ecoboost daily beater
DSG2003Mach1 is offline   Reply With Quote
Old 05-03-2018, 01:56 AM   #4
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Power Window acting up

Your bushings inside the motor have flattened and are stuck. Take the motor out, open it up, remove the bushings, clean, grease up and when installing them flip the bushings. To prevent this from happening in the future, if you keep your car in the garage, roll up the window and just slightly tap the window button so pressure is not put on those bushings with the window in the full up position.

Did this to mine in 2009 and have never had a problem since. Also had this same issue in my daughters 04 GT and it still works like a champ. Or, buy a new motor. Sadly, you cannot buy that bushing anywhere, but that is the part they replace when they rebuild them.

good luck
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 05-03-2018, 09:22 AM   #5
j rick kirby
Registered User
 
Join Date: Aug 2004
Location: Winston-Salem,NC
Posts: 1,802
Re: Power Window acting up

Interesting. Mine has done that a few times over the years and it seemed to be heat related. Car sitting in the sun in the summer for example. Take it home and put it in the garage or park the car where it could cool a little and it will start working again.
__________________
2003 Azure mach1 5 speed with IUP
Maximum Motorsports R&T Box with Torque Arm and lots of other bits and pieces here and there
2012 Candy Red Metalic Premium GT with Brembo/Trak Pak and 373s
HPDE Instructor
j rick kirby is offline   Reply With Quote
Old 05-03-2018, 05:48 PM   #6
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Power Window acting up

Quote:
Originally Posted by j rick kirby View Post
Interesting. Mine has done that a few times over the years and it seemed to be heat related. Car sitting in the sun in the summer for example. Take it home and put it in the garage or park the car where it could cool a little and it will start working again.
That is your issue, exactly how mine started.
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 05-03-2018, 10:44 PM   #7
crazyone64
Registered User
 
Join Date: Apr 2008
Location: Toronto
Posts: 16
Re: Power Window acting up

Interesting, with the temperature dropping at night, the power window works.

Why would the hot weather cause my power window to stop working?
Does it help confirm it is the motor?

Thanks everyone!
crazyone64 is offline   Reply With Quote
Old 05-04-2018, 03:35 AM   #8
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Power Window acting up

Quote:
Originally Posted by crazyone64 View Post
Interesting, with the temperature dropping at night, the power window works.

Why would the hot weather cause my power window to stop working?
Does it help confirm it is the motor?

Thanks everyone!
confirms its the rubber stoppers in the motor, when you take it out and open it up you will know exactly what I am talking about.

here is a pic:
its the black rubber part, clean, flip, grease... done.
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 05-04-2018, 08:19 PM   #9
crazyone64
Registered User
 
Join Date: Apr 2008
Location: Toronto
Posts: 16
Re: Power Window acting up

I've got the door panel off, removed the 3 bolts on the motor, 2 nuts on the rivets, couldn't remove the motor though.

I was trying to follow what the guy in this video did https://www.youtube.com/watch?v=5dNcCN27p3Q
Based on the comments, others seem to be able move it out easily.

I started taking off more nuts and was able to slide the motor back, the window fell so I'll look into the process for removing the whole assembly tomorrow.

Last edited by crazyone64; 05-04-2018 at 09:14 PM.
crazyone64 is offline   Reply With Quote
Old 05-04-2018, 09:12 PM   #10
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Power Window acting up

I did not have any rivets that needed to be removed; just removed the three bolts, you need to tap the window button down to help relieve the pressure that has the motor wedged in.
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 05-04-2018, 09:16 PM   #11
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Power Window acting up

Also, don't use metal nuts for bushings... lol
that video is terrible.
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 05-05-2018, 03:42 PM   #12
crazyone64
Registered User
 
Join Date: Apr 2008
Location: Toronto
Posts: 16
Re: Power Window acting up

I've got the whole assembly out, The spring was holding the motor in tight, and through some playing the motor shot out a little nervously and the assembly changed direction/compressed..

I cleaned and greased all the components, switched it around like you said, everything looks good. Put the motor back together, but not sure about lining up the gears on the assembly with the gears on the motor.

Anyone have this in the service manual?
I placed it in a vise making it easier, but again, not sure which knotch to place the motor gear on..

Last edited by crazyone64; 05-05-2018 at 08:31 PM.
crazyone64 is offline   Reply With Quote
Old 05-05-2018, 08:19 PM   #13
crazyone64
Registered User
 
Join Date: Apr 2008
Location: Toronto
Posts: 16
Re: Power Window acting up

With those gears misaligned, its impossible to fit the assembly matching the bolt holes.
I think my only option is to buy a new assembly with motor, line mine up identically to the new one and try again, then return the new one.
Seems easier than taking out the passenger side and potentially running into issues there, unless someone has a better idea?
crazyone64 is offline   Reply With Quote
Old 05-05-2018, 09:56 PM   #14
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Power Window acting up

trying to understand; you should be able to put the window in the up position, then put the motor in, you may have to connect the power to the motor and rotate the gear with the button, it has some torque to it so hold it tight. If you have pictures of your issue that may help. I was able to wiggle mine in with ease, I've done at least 4 of these and even one on the convertible rear windows.
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 05-05-2018, 10:38 PM   #15
crazyone64
Registered User
 
Join Date: Apr 2008
Location: Toronto
Posts: 16
Re: Power Window acting up

That may have been my issue. I was attaching the motor to the assembly because those arms were pretty tough to move with the spring tension.. then installing the piece as one. So I wasn't sure which of those grooves/notches on the regulator assembly to make contact with the motor gear as you can pick one of like 30 options, changing the degree of the arms.. And the misalignment.

Tomorrow I'll disconnect the motor, install the regulator assembly, raise the window all the way, then install the motor. Hopefully those are the correct steps and everything lines up. I imagine the spring will make this difficult to get the arms where I want.
If I missed anything please let me know.
Thanks!

Last edited by crazyone64; 05-05-2018 at 11:04 PM.
crazyone64 is offline   Reply With Quote
Old 05-06-2018, 01:23 PM   #16
crazyone64
Registered User
 
Join Date: Apr 2008
Location: Toronto
Posts: 16
Re: Power Window acting up

I raised the window, reattached the assembly, lined up all holes, tightened bolts. Haven't installed the motor yet, because manually moving the window, will only go down about 4-5 inches. It's hitting something - it sounds like the bumper on the top right track.

When i remove the bar in picture 1, the window moves down no problem. All remaining nuts and screws are in place.
From what i can see, it is lined up in picture 2 with the window up, but as i move the window down 4-5 inches, in picture 3, it moves out of the tracks position, and with that bar in place, i think it's affecting the top right arm? (where I'm guessing it's hitting the bumper)
The issue might be here?

Thanks for your patience!

I'm so close to the finish but completely stuck.
Attached Thumbnails
1.jpg   2.jpg   3.jpg  

Last edited by crazyone64; 05-06-2018 at 08:23 PM. Reason: T LT
crazyone64 is offline   Reply With Quote
Old 05-06-2018, 09:19 PM   #17
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Power Window acting up

sorry bud, hopefully someone jumps in here; I have never messed with anything but those 3 bolts on the motor, never touched any other rivet or bolts. I was trying to get to you before you messed with all of that other jazz...
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 05-06-2018, 09:40 PM   #18
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,005
Re: Power Window acting up

Check how the other door is done?
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁
311-420 is offline   Reply With Quote
Old 05-07-2018, 08:05 PM   #19
crazyone64
Registered User
 
Join Date: Apr 2008
Location: Toronto
Posts: 16
Re: Power Window acting up

I've got a really interesting update..

I reinstalled the assembly this time with the window a bit down instead of fully up.

I found exactly what is hitting.

Behind the speaker, there is a vertical track the window goes up and down on shown in picture 1.

I fit my camera in there as shown in Picture 2 and 3, and I can see a white piece that is hitting the metal as i raise the window. This is the issue. In picture 2, you can see it has scrape marks, so it must go under the metal, but i can't budge it in.. when i have the window fully up, and install the assembly, it hits on the top part, but is hidden from view. Same sound.
When i take out the assembly, i have more wiggle room with the glass and can slide the window up and down.

Anyone familiar with this or where i can get more specific advice on this?
Attached Thumbnails
0.jpg   1b.jpg   2.jpg  

Last edited by crazyone64; 05-07-2018 at 08:47 PM.
crazyone64 is offline   Reply With Quote
Old 05-11-2018, 10:11 AM   #20
crazyone64
Registered User
 
Join Date: Apr 2008
Location: Toronto
Posts: 16
Re: Power Window acting up

That white clip fell out of the window rail track.

Solution:
Remove the nut on the Window Rail, lower the window a bit, put the clip back in the rail, re-assemble everything.
Hope this helps someone in the future. It was a royal pain.
crazyone64 is offline   Reply With Quote
Old 07-23-2018, 01:13 PM   #21
ab_mach1
Lorraine's driver
 
ab_mach1's Avatar
 
Join Date: Apr 2012
Location: Indianapolis, IN
Posts: 2,442
Re: Power Window acting up

Quote:
Originally Posted by crazyone64 View Post
That white clip fell out of the window rail track.

Solution:
Remove the nut on the Window Rail, lower the window a bit, put the clip back in the rail, re-assemble everything.
Hope this helps someone in the future. It was a royal pain.
Is that the mount toward the front of the car? There's three mounting points and it kinda looks like what fell off my window lol. My window goes up and down okay, but the window rattles on bumps when the window is down. I'm not sure how in the heck it fell off the window. Maybe the bracket cam out of the track, like yours, only it got caught on the track and pulled off the mount bracket..?

Click image for larger version

Name:	windowmount.jpg
Views:	8
Size:	122.1 KB
ID:	66905
__________________
  • Instagram: @azurblumach1
  • SCT X3 with LaSota Racing tune
  • Borla Stingers w/JBA off road H pipe
  • MGW short shifter w/comfort handle
  • Eibach Sportlines w/Koni STR.T's and Maximum Motorsports CC plates
ab_mach1 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:36 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<