2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Power Adders

Power Adders Superchargers, Turbos, Nitrous, etc...

Reply
 
Thread Tools Display Modes
Old 01-27-2015, 09:43 PM   #151
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

Quote:
Originally Posted by Mach828 View Post
Get your tuner to run a lot of timing under 4k on e85. Like 22 degrees. Then you can taper it off if you'd like up top. It will run strong.

If my little S trim can run 118 trap times with a 6,500 DA, yours should be able to take down a mid 120 trap CJ coyote in San Antonio. I ran mine at 18 degrees with a little leaded 110 mixed with 91. With e85 you should be good with 18+ and 10lbs. I'd do 22 degrees under 4k and taper it off to 18 at 7k.

Did you swap the snap ring on your auto so you can rev it to 7k?

I'm betting on you vs the ported CJ coyote


Yes, snap ring has been swapped. Highest I ever spinned it to was 6,800 rpm so far.
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 01-27-2015, 10:22 PM   #152
SHAKN' 04
Registered User
 
SHAKN' 04's Avatar
 
Join Date: Jan 2008
Location: Kyle, Texas
Posts: 2,285
Re: Starting my Build

Haha then we'll have to see how it plays out when both cars are done.
__________________
**SOLD**04' Mach 1
-Comp Cams 106100's (deg 106/110)
-Eatonswap with 3.4 Pulley
-Full Exhaust (mac lts & xpipe, sss terminator c/b)
-Built Rear w/ 3.55 gears

[B]-Tuned by Lethal Performance of San Antonio
-510hp/478tq
SHAKN' 04 is offline   Reply With Quote
Old 02-13-2015, 10:06 AM   #153
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

I didn't want drop to much on the fuel system so i ordered lethals budget return system. Should be here today or Monday. I guess I can turn up the boost now
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 05-19-2015, 06:13 PM   #154
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

http://m.youtube.com/watch?v=iIIuR-HjFho

Not much going on here...lol
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.

Last edited by SuperMach1; 05-20-2015 at 05:11 PM.
SuperMach1 is offline   Reply With Quote
Old 06-13-2015, 07:32 AM   #155
jeffrey1
Registered User
 
Join Date: Jun 2014
Location: manalapan
Posts: 227
Re: Starting my Build

Did you ever finish this project how much power did it make any track times
jeffrey1 is offline   Reply With Quote
Old 06-13-2015, 09:05 AM   #156
SHAKN' 04
Registered User
 
SHAKN' 04's Avatar
 
Join Date: Jan 2008
Location: Kyle, Texas
Posts: 2,285
Re: Starting my Build

Waiting for injector install and new tune on E85. Track is open and I'll be waiting sir
__________________
**SOLD**04' Mach 1
-Comp Cams 106100's (deg 106/110)
-Eatonswap with 3.4 Pulley
-Full Exhaust (mac lts & xpipe, sss terminator c/b)
-Built Rear w/ 3.55 gears

[B]-Tuned by Lethal Performance of San Antonio
-510hp/478tq
SHAKN' 04 is offline   Reply With Quote
Old 06-16-2015, 09:11 PM   #157
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

Quote:
Originally Posted by jeffrey1 View Post
Did you ever finish this project how much power did it make any track times
Nah man, car is still at the shop getting looked over. I'll be taking it somewhere else soon if they don't get started on it.
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 06-16-2015, 09:14 PM   #158
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

Quote:
Originally Posted by SHAKN' 04 View Post
Waiting for injector install and new tune on E85. Track is open and I'll be waiting sir

Did you already swap intakes? That thing is going to be a beast NA.

But not enough....lol
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 06-16-2015, 11:03 PM   #159
SHAKN' 04
Registered User
 
SHAKN' 04's Avatar
 
Join Date: Jan 2008
Location: Kyle, Texas
Posts: 2,285
Re: Starting my Build

Quote:
Originally Posted by SuperMach1 View Post
Did you already swap intakes? That thing is going to be a beast NA.

But not enough....lol
Yep. Gonna order a drag/kill set up for it and hit the track
__________________
**SOLD**04' Mach 1
-Comp Cams 106100's (deg 106/110)
-Eatonswap with 3.4 Pulley
-Full Exhaust (mac lts & xpipe, sss terminator c/b)
-Built Rear w/ 3.55 gears

[B]-Tuned by Lethal Performance of San Antonio
-510hp/478tq
SHAKN' 04 is offline   Reply With Quote
Old 06-22-2015, 08:30 PM   #160
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

Lucky you!!! Hmu with the times. Im sure you'll be at the track before my car is ready...
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 08-07-2015, 08:27 PM   #161
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

And she Lives!!!!!!
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 08-08-2015, 10:38 PM   #162
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

First start video.

https://m.youtube.com/watch?v=hzAwnQ11_7Y
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 08-08-2015, 10:44 PM   #163
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
Re: Starting my Build

Awesome !! I wish my P1 was loud like that, mine is really quiet, all you hear is the Tial, blower does more of a marble in a coffee can than a sweet whine like that...mucho congrats
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 08-10-2015, 11:04 PM   #164
lonestarbullitt
Registered User
 
Join Date: Aug 2011
Location: Helotes, TX
Posts: 179
Re: Starting my Build

that thing is screaming. Sounds good! You gotta love that initial start up when all the work is paying off. Who is gonna tune it for you? Lethal did a good job in mine with a conservative tune making 533.
lonestarbullitt is offline   Reply With Quote
Old 08-11-2015, 01:38 PM   #165
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

Thanks Not a GT.

Lonestar, Chris at South Texas Performance has always done my tuning, I think im just going to stick with him. Whats your setup and what fuel?
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 08-11-2015, 01:50 PM   #166
lonestarbullitt
Registered User
 
Join Date: Aug 2011
Location: Helotes, TX
Posts: 179
Re: Starting my Build

Quote:
Originally Posted by SuperMach1 View Post
Thanks Not a GT.

Lonestar, Chris at South Texas Performance has always done my tuning, I think im just going to stick with him. Whats your setup and what fuel?
Kotzur built Teksid motor around a 10.5:1 compression, minor porting work on the heads, 98 cobra cams, 42lb injectors, focus svt fuel pump with KB BAP, Vortech V2 with a 2.95 pulley pushing around 12-15#, treadstone FMIC with Vortech MaxFlow blow off and SCT BA5000 slot style MAF.





I have since this last picture moved the blow off valve to the hot side of the intercooler.
lonestarbullitt is offline   Reply With Quote
Old 08-11-2015, 08:18 PM   #167
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

Good numbers and sweet build! Are your cams degreed? and is Shawn back at lethal doing the tunig?
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 08-11-2015, 10:41 PM   #168
lonestarbullitt
Registered User
 
Join Date: Aug 2011
Location: Helotes, TX
Posts: 179
Re: Starting my Build

Quote:
Originally Posted by SuperMach1 View Post
Good numbers and sweet build! Are your cams degreed? and is Shawn back at lethal doing the tunig?
Thanks man! Likewise you to have a pretty sick build! I can't wait to see what numbers she'll put down. Yes Kotzur degreed the cams, I don't know the specs tho, I just paid the bill . Yes Shawn is still over at Lethal, he has tuned my car for all three sessions that I've had over there. Maybe one night we'll all have to make a trip out to San Antonio Raceway now that it's open again.
lonestarbullitt is offline   Reply With Quote
Old 08-12-2015, 08:01 PM   #169
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

Quote:
Originally Posted by lonestarbullitt View Post
Maybe one night we'll all have to make a trip out to San Antonio Raceway now that it's open again.
For sure!
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 08-14-2015, 05:52 PM   #170
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

Quote:
Originally Posted by lonestarbullitt View Post
Kotzur built Teksid motor around a 10.5:1 compression, minor porting work on the heads, 98 cobra cams, 42lb injectors, focus svt fuel pump with KB BAP, Vortech V2 with a 2.95 pulley pushing around 12-15#, treadstone FMIC with Vortech MaxFlow blow off and SCT BA5000 slot style MAF.





I have since this last picture moved the blow off valve to the hot side of the intercooler.
which intercooler did you go with?
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 12-01-2015, 04:51 PM   #171
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

Car should be on the dyno next week (finally). Now it's time for the guessing game. What are your thoughts on hp/torque? Im guessing or hoping for 540/500 to the wheels.

-Forged block
-11.3 cr
-Slightly ported heads, 1mm intake valves, 4 angle valve job
-98 cobra intake cams degreed @114/114
-3in. Exhaust
-P1 11-12 psi
-E-85.

*Built Auto w/ 3600 stall
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.

Last edited by SuperMach1; 12-01-2015 at 10:31 PM.
SuperMach1 is offline   Reply With Quote
Old 03-09-2016, 01:31 PM   #172
SuperMach1
Never Satisfied
 
SuperMach1's Avatar
 
Join Date: Sep 2007
Location: San Antonio, TX
Posts: 1,134
Re: Starting my Build

Its been a while so i thought I'd update this. My car was having transmission issues on the dyno so I had to get it rebuit. Also went ahead and ordered a Circle D 3800 triple disk converter . The transmission builder told me it would handle 850hp which is more then what i need but i can't complain. And I'm hoping to have the Mach back within in the next 2 weeks (fingers crossed).

This Sh!t is starting to get reaaaallly expensive!!! I'm just glad i haven't gave up on it.
__________________
P1 8psi @ 6k
PA Transmission
DD 3,600 Stall
BBK LT's w/ 3in Collector
Custom 3in X-Pipe
Custom 3in CB w/ Pypes 3in M-80's
Built Rear w/ 4:10
415/383
PB 11.80, @ 119 with a 1.71 60ft
Tuned by http://www.southtexasperformance.com/

Built WAP Block, 10.5:1 compression, 14psi, E-85 Coming soon.
SuperMach1 is offline   Reply With Quote
Old 03-09-2016, 01:41 PM   #173
ASH302
Soldier for Christ
 
ASH302's Avatar
 
Join Date: May 2009
Location: Willis, TX at The Daddy ASh Ranch
Posts: 30,596
Re: Starting my Build

Thanks for the updating, sucks about having it on the dyno and issues come up and nothing wrong with being safer on what parts you are adding in there.
the two weeks will be here before you know it. good luck once you get her back

ASh
__________________
2001 lazer red v6 Mustang coupe sold in Aug 2006
2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012
2013 grey 6 speed coupe GT Mustang Sold in Feb 2014
2013 RED Dodge Charger R/T Sold Nov 2014
2002 custom Blue 02 Auto Trans AM Sold June 2015
1998 Cobra Black Sold summer 2016

Current
2009 Ford F350 FX4 March 2017 (work truck)
2003 OW 5.0 Mach 1 Aug 2020

ASh
ASH302 is offline   Reply With Quote
Old 03-09-2016, 04:13 PM   #174
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
Re: Starting my Build

Quote:
Originally Posted by SuperMach1 View Post
Its been a while so i thought I'd update this. My car was having transmission issues on the dyno so I had to get it rebuit. Also went ahead and ordered a Circle D 3800 triple disk converter . The transmission builder told me it would handle 850hp which is more then what i need but i can't complain. And I'm hoping to have the Mach back within in the next 2 weeks (fingers crossed).

This Sh!t is starting to get reaaaallly expensive!!! I'm just glad i haven't gave up on it.
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 03-09-2016, 06:28 PM   #175
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Starting my Build

Quote:
Originally Posted by SuperMach1 View Post

This Sh!t is starting to get reaaaallly expensive!!! I'm just glad i haven't gave up on it.
This is what I learned:
400rwhp - impressive and can hide the expense from the family, maintenance, take lunch to work.
500rwhp - getting serious and the wife's eyebrows are creeping higher
600rwhp - hp curve is almost pure vertical, so is your budget expense. No hiding this budget, you have officially joined insanity because you cannot justify any of it. (fwiw, 'but look at how happy I am' does NOT work)
750rwhp+ - Pure race car, no justification, just throw the budget out the window, you are way over your original estimate. Time to man up and buy her a mustang of her own, that is the only way she will understand.

as a sub note; from family and co-workers I never get ask how fast, quick, etc. The number 1 question is alway 'what is the MPG'; this deserves a slap on the back of the head, I'd drive a prius if I was concerned about that. BTW, it is 10MPG city, 14 highway. lol
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:53 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<