|
|
Photo Gallery | $ Donations $ | Register | FAQ | Social Groups | Calendar | Search | Today's Posts | Mark Forums Read |
|
Thread Tools | Display Modes |
09-27-2012, 10:19 PM | #1 |
Machinator
Join Date: Jul 2008
Location: Leesburg, VA
Posts: 2,294
|
How To: Front Wheel Bearing Hub Assembly
A worn front wheel bearing can cause swaying while driving, vibrations, grinding sounds, and safety problems causing you to NOT GO FAST.
Time:45Mins Tools Necessary: -Torque wrench capable of 250ftlbs 1/2'' attachment -Flat Head Screw Driver -Hammer -Jack -Jack Stands -36mm 1/2'' Deep-dish Socket -15mm Socket -Breaker-bar or Leverage-bar -Replacement Hub assembly With ABS ring -Front brake pad tool -Man's best friend for company Steps: 1. Loosen front lug nuts 2. Jack up car and safely place jack stands 3. Remove wheels 4. Remove pin from brake calipers, and tie them up and away. 5. Take the 15mm socket and back-out the 2 bolts that hold the caliper assembly on and remove. 6. Remove rotor
__________________
2004 D.S.G. Mach 1 Mustang I.U.P.(01/22/2004)-04 Cobra Longblock- Posi Ported M122 GT500 Blower - BF 2.93 Upper - 4lb Lower -MGW STS-Bassani cattless X pipe- Borla Stinger Catback-Steeda Bump Steer kit-MM CCs- MM Coilovers 350lb spring- LFP Heat-exchanger- 1inch Shaker Spacer-03 Cobra IRS with FTBR's Full Bushings kit-BF Diff Brace-3:55 gears -T56 Tranzilla- cut 04 coupe rear springs-Viper Remote Start/Alarm system-Ipod Auxilary-SLP LL-Tune coming soon |
09-27-2012, 10:20 PM | #2 |
Machinator
Join Date: Jul 2008
Location: Leesburg, VA
Posts: 2,294
|
Re: How To: Front Wheel Bearing Hub Assembly
7. Get flat head screw driver and hammer, pry the cap little by little rotating it in a star pattern until it pops off.
8. Use your breaker-bar or leverage bar with a 1/2'' attachment with the 36mm socket to remove the wheel bearing retaining nut. 9. Remove the wheel hub assembly, mine just slid off with a little work, some have had to tap it out with a hammer.
__________________
2004 D.S.G. Mach 1 Mustang I.U.P.(01/22/2004)-04 Cobra Longblock- Posi Ported M122 GT500 Blower - BF 2.93 Upper - 4lb Lower -MGW STS-Bassani cattless X pipe- Borla Stinger Catback-Steeda Bump Steer kit-MM CCs- MM Coilovers 350lb spring- LFP Heat-exchanger- 1inch Shaker Spacer-03 Cobra IRS with FTBR's Full Bushings kit-BF Diff Brace-3:55 gears -T56 Tranzilla- cut 04 coupe rear springs-Viper Remote Start/Alarm system-Ipod Auxilary-SLP LL-Tune coming soon |
09-27-2012, 10:21 PM | #3 |
Machinator
Join Date: Jul 2008
Location: Leesburg, VA
Posts: 2,294
|
Re: How To: Front Wheel Bearing Hub Assembly
10. Replace with new unit tapping it in a star pattern to seat it properly.
11. Reinstall Retaining nut, tighten and use your 36mm socket and torque wrench. I've read multiple how- to's regarding the TQ rating and they varied from 246ftlbs to 258ftlbs. I just went and maxed my torque wrench out at 250tqlbs. 12. Reinstall the cap, rotor and caliper assembly holder. 13. Reinstall your caliper, you might need to push the pads and pistons in to fit it over the rotor again. 14. Reinstall wheel, lug nuts, tighten them, lower the car, re-tighten the lugs again. Test drive. Enjoy!:beer:
__________________
2004 D.S.G. Mach 1 Mustang I.U.P.(01/22/2004)-04 Cobra Longblock- Posi Ported M122 GT500 Blower - BF 2.93 Upper - 4lb Lower -MGW STS-Bassani cattless X pipe- Borla Stinger Catback-Steeda Bump Steer kit-MM CCs- MM Coilovers 350lb spring- LFP Heat-exchanger- 1inch Shaker Spacer-03 Cobra IRS with FTBR's Full Bushings kit-BF Diff Brace-3:55 gears -T56 Tranzilla- cut 04 coupe rear springs-Viper Remote Start/Alarm system-Ipod Auxilary-SLP LL-Tune coming soon |
09-27-2012, 10:37 PM | #4 |
Registered User
Join Date: May 2005
Location: Woodstock,GA
Posts: 544
|
Re: How To: Front Wheel Bearing Hub Assembly
Thanks for the write up. Where'd you get the replacement from?
__________________
I/E, 4:10's, tune |
09-27-2012, 10:45 PM | #5 |
Machinator
Join Date: Jul 2008
Location: Leesburg, VA
Posts: 2,294
|
Re: How To: Front Wheel Bearing Hub Assembly
I had member LOOKnGO help me out with the hub. But I would have used Tousely Ford's parts depo page for it. http://www.tousleyfordparts.com/
__________________
2004 D.S.G. Mach 1 Mustang I.U.P.(01/22/2004)-04 Cobra Longblock- Posi Ported M122 GT500 Blower - BF 2.93 Upper - 4lb Lower -MGW STS-Bassani cattless X pipe- Borla Stinger Catback-Steeda Bump Steer kit-MM CCs- MM Coilovers 350lb spring- LFP Heat-exchanger- 1inch Shaker Spacer-03 Cobra IRS with FTBR's Full Bushings kit-BF Diff Brace-3:55 gears -T56 Tranzilla- cut 04 coupe rear springs-Viper Remote Start/Alarm system-Ipod Auxilary-SLP LL-Tune coming soon |
10-05-2012, 04:14 PM | #6 |
Mach-T
Join Date: Jun 2004
Location: DFW
Posts: 2,865
|
Re: How To: Front Wheel Bearing Hub Assembly
Nice write-up, I just did mine a few months ago. Exactly the same steps you showed, minus the use of the breaker bar, I used my impact wrench to get that beast off.
I purchased mine off of amazon, Timken was the brand. I think they were ~40 each. This should be a sticky!!!
__________________
Darrell Black '04 Mach 1 Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67 (100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88 New build - 750rwhp; not track tested (yet) Mods: Build Log Paint&Body Tuned by Manny @ HPP |
10-17-2012, 11:14 PM | #7 |
Registered User
Join Date: Oct 2012
Location: Gainesville
Posts: 37
|
Re: How To: Front Wheel Bearing Hub Assembly
exactly how i did mine on my 96 a couple years ago. but i did use an impact on the hub nut instead of a breaker bar. mine didn't slide off with little work. I had to work in a circle and tap it off with a hammer. a lot of corroded spots.
__________________
03 Mach 1 Azure Blue |
10-18-2012, 12:38 AM | #8 |
Machinator
Join Date: Jul 2008
Location: Leesburg, VA
Posts: 2,294
|
Re: How To: Front Wheel Bearing Hub Assembly
Thanks guys, glad to help
__________________
2004 D.S.G. Mach 1 Mustang I.U.P.(01/22/2004)-04 Cobra Longblock- Posi Ported M122 GT500 Blower - BF 2.93 Upper - 4lb Lower -MGW STS-Bassani cattless X pipe- Borla Stinger Catback-Steeda Bump Steer kit-MM CCs- MM Coilovers 350lb spring- LFP Heat-exchanger- 1inch Shaker Spacer-03 Cobra IRS with FTBR's Full Bushings kit-BF Diff Brace-3:55 gears -T56 Tranzilla- cut 04 coupe rear springs-Viper Remote Start/Alarm system-Ipod Auxilary-SLP LL-Tune coming soon |
03-15-2014, 12:06 PM | #9 |
Registered User
Join Date: Apr 2011
Location: jacksonville,nc
Posts: 170
|
Re: How To: Front Wheel Bearing Hub Assembly
Do you have to put grease on it at all?
|
03-15-2014, 12:43 PM | #10 |
Registered User
Join Date: Feb 2013
Location: NEW YORK HIGHEST TAXES IN AMERICA
Posts: 603
|
Re: How To: Front Wheel Bearing Hub Assembly
|
03-15-2014, 04:20 PM | #11 |
Registered User
Join Date: Apr 2011
Location: jacksonville,nc
Posts: 170
|
Re: How To: Front Wheel Bearing Hub Assembly
of course none of the 10 part stores around me have the nut. Can you reuse the same nut?
Last edited by 66gam; 03-15-2014 at 04:37 PM. |
03-15-2014, 06:18 PM | #12 |
Registered User
Join Date: Feb 2013
Location: NEW YORK HIGHEST TAXES IN AMERICA
Posts: 603
|
Re: How To: Front Wheel Bearing Hub Assembly
|
03-16-2014, 05:44 PM | #13 |
Machinator
Join Date: Jul 2008
Location: Leesburg, VA
Posts: 2,294
|
Re: How To: Front Wheel Bearing Hub Assembly
Correct, no need for greasing a new unit. It has grease applied to it already. And yup you can reuse the nut. I went to Ford to get it
__________________
2004 D.S.G. Mach 1 Mustang I.U.P.(01/22/2004)-04 Cobra Longblock- Posi Ported M122 GT500 Blower - BF 2.93 Upper - 4lb Lower -MGW STS-Bassani cattless X pipe- Borla Stinger Catback-Steeda Bump Steer kit-MM CCs- MM Coilovers 350lb spring- LFP Heat-exchanger- 1inch Shaker Spacer-03 Cobra IRS with FTBR's Full Bushings kit-BF Diff Brace-3:55 gears -T56 Tranzilla- cut 04 coupe rear springs-Viper Remote Start/Alarm system-Ipod Auxilary-SLP LL-Tune coming soon |
02-17-2017, 02:46 PM | #14 |
Machinator
Join Date: Jul 2008
Location: Leesburg, VA
Posts: 2,294
|
Re: How To: Front Wheel Bearing Hub Assembly
A little bump for anyone needing it,
__________________
2004 D.S.G. Mach 1 Mustang I.U.P.(01/22/2004)-04 Cobra Longblock- Posi Ported M122 GT500 Blower - BF 2.93 Upper - 4lb Lower -MGW STS-Bassani cattless X pipe- Borla Stinger Catback-Steeda Bump Steer kit-MM CCs- MM Coilovers 350lb spring- LFP Heat-exchanger- 1inch Shaker Spacer-03 Cobra IRS with FTBR's Full Bushings kit-BF Diff Brace-3:55 gears -T56 Tranzilla- cut 04 coupe rear springs-Viper Remote Start/Alarm system-Ipod Auxilary-SLP LL-Tune coming soon |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|