2003-04 Mach 1 Registry Owners Club  

Best Mustang Parts

Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Engine & Drivetrain (Including trans & rear axles)

Reply
 
Thread Tools Display Modes
Old 06-21-2019, 09:53 PM   #1
noodle9400
Registered User
 
Join Date: May 2008
Location: Egg Harbor City, NJ
Posts: 191
Possible Gear Install f-up 😒

So to start...I shouldíve paid a shop to do my gear install. Had the parts for a while and was strap for cash. So I had someone on the side do it.

So after break in period I started noticing a noise when backing into my driveway. My driveway has a small incline so when I backed the car up, feathered the clutch and gas on the driveway to give a rocking feel, as it was backing up it would sound like the I was adding stress causing hard grinding/rubbing sound. Found out I had a leak at the rear. After break in period I decided to change the oil and check things myself. Had royal purple in there and with less than 800 miles the oil was grey. Oil was leaking at the pinion seal and cover.

My question(s) for all of you is this... if the pinion flange was installed without marking or counting threads to get previous pre-load, how can I install a new pinion seal and make the new nut is at the right pre-load? The old crush sleeve was used. If that was used and not following the original pre-load, could that cause the issues Iím heaving? If so, can that crush sleeve be replaced?


Iím not sure the flange nut was marked so the new flange nut was installed to the pre-load as original install. Also, the original crush-sleeve was used. Is it common to use the old crush-sleeve? When i goto install the new pinion seal, how
noodle9400 is offline   Reply With Quote
Old 06-21-2019, 10:29 PM   #2
falcongtho3
Moderating at Mach 1
 
falcongtho3's Avatar
 
Join Date: Aug 2002
Location: Baton Rouge, La.
Posts: 15,964
Re: Possible Gear Install f-up 😒

From my own, sad, experience...always use a new crush sleeve.

__________________
Krewe de la Mach Rouge

#340804 13th Mach 1 built
11/07/02 Build Date
12/13/02 Delivery
falcongtho3 is offline   Reply With Quote
Old 06-23-2019, 06:48 PM   #3
fastlane
Registered User
 
Join Date: Mar 2011
Location: Fort Worth, TX
Posts: 209
Re: Possible Gear Install f-up 😒

I always use a new crush sleeve. Sounds like you will need to pull it apart, install a new crush sleeve and pinion seal. The carrier needs to be out of the rear end to properly measure the bearing preload. The preload needs to be 8-16 in. lbs. for used bearings and 22-28 in. lbs. for new bearings. Crushing the sleeve is no easy task either. An impact will get things going but you will need a flange holder tool and some hefty breaker bars to completely crush it. Work slow with the install as once it starts to crush, the preload jumps quickly. You don't want to put too much preload and then back the flange nut off as you will just have to start over with a new sleeve.

Also, did you get a good pattern on the ring gear when installing the new gears? I always hold the ring gear tight when testing the pattern. If you didn't get all that done right, you maybe chewing up the bearings or gear faces. The gear oil shouldn't be discolored after such a short time unless you are chewing something up.
fastlane is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:33 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<