2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Power Adders

Power Adders Superchargers, Turbos, Nitrous, etc...

Reply
 
Thread Tools Display Modes
Old 04-07-2008, 05:04 PM   #126
cre8787
Eaton Swapped Azure
 
cre8787's Avatar
 
Join Date: Mar 2008
Location: Germantown, Maryland
Posts: 246
Re: Eaton Swap.....

Quote:
Originally Posted by No1Ford View Post
Your going to have to wire in a relay for the pump.
Would it be possible to just run a toggle switch to it?
cre8787 is offline   Reply With Quote
Old 04-07-2008, 08:52 PM   #127
TR04MACH
Registered User
 
Join Date: Dec 2005
Location: Herndon, VA
Posts: 541
Re: Eaton Swap.....

Quote:
Originally Posted by cre8787 View Post
Would it be possible to just run a toggle switch to it?
There is really no reason to ever have it off. I wouldn't think that would be a great idea unless you could monitor your temps there. Wired the way everyone does basically turns it on when your key is in the on position even if the engine isn't. That makes sure its on when you need it. In my opinion it would be too easy to forget to turn it on and that wouldn't be good having super heated coolant stuck in your blower raising those temps.
__________________
2004 Torch Red Mach 1!
Eaton Swapped 8psi
SLP Longtube Headers
SLP Catted Shorty X
SLP Powerflo Catback
JLT RAI Intake
SCT Tune on 4bank chip
Nitto DR 275/40/17
MM Lower Control Arms
MM Urethane Rack Bushings
Hawk HPS Pads w/ MM brake lines
MM Full Length Subframes
Steeda Tri-ax
Sirius

For Sale!
TR04MACH is offline   Reply With Quote
Old 04-08-2008, 02:22 PM   #128
cre8787
Eaton Swapped Azure
 
cre8787's Avatar
 
Join Date: Mar 2008
Location: Germantown, Maryland
Posts: 246
Re: Eaton Swap.....

I see your point, thanks a lot.
cre8787 is offline   Reply With Quote
Old 04-11-2008, 10:47 PM   #129
machgsxr
Registered User
 
machgsxr's Avatar
 
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
Re: Eaton Swap.....

Pics of my shaker bracket. Simple, yet it does the job perfectly.
Attached Thumbnails
Mach 1 003.jpg   Mach 1 004.jpg   Mach 1 006.jpg   Mach 1 007.jpg  
machgsxr is offline   Reply With Quote
Old 04-12-2008, 09:57 AM   #130
No1Ford
Registered User
 
No1Ford's Avatar
 
Join Date: Apr 2006
Location: MN
Posts: 555
Re: Eaton Swap.....

Does that move around at all? Or are you using a locking washer to keep it tight? It looks like it may move around, thats why i'm asking?
__________________
No1Ford is offline   Reply With Quote
Old 04-12-2008, 12:09 PM   #131
cveater
Registered User
 
cveater's Avatar
 
Join Date: Mar 2008
Location: palm city fl
Posts: 22
Re: Eaton Swap.....

how much did everything cost from installation stuff to the eaton.......
__________________
Ls1 pwner
cveater is offline   Reply With Quote
Old 04-12-2008, 03:01 PM   #132
cre8787
Eaton Swapped Azure
 
cre8787's Avatar
 
Join Date: Mar 2008
Location: Germantown, Maryland
Posts: 246
Re: Eaton Swap.....

Im right at $2,652 for everything but tune. I should be looking at $3,150 for the complete swap and tune. I came across a sweet deal, guy gave me everything down to the last bolt for $2,500. The only thing he didnt throw in was the throttle and crusie control cable. Even came with fuel tank/ pumps, a new alternator, and a JLT CAI.
cre8787 is offline   Reply With Quote
Old 04-12-2008, 03:03 PM   #133
cre8787
Eaton Swapped Azure
 
cre8787's Avatar
 
Join Date: Mar 2008
Location: Germantown, Maryland
Posts: 246
Re: Eaton Swap.....

Quote:
Originally Posted by machgsxr View Post
Pics of my shaker bracket. Simple, yet it does the job perfectly.
I noticed that you do not have the 3 EGR connectors that bracket to the drivers side of the Eaton. Are those connectors nesasary? Someone told me that you dont need them.
cre8787 is offline   Reply With Quote
Old 04-12-2008, 11:41 PM   #134
machgsxr
Registered User
 
machgsxr's Avatar
 
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
Re: Eaton Swap.....

Quote:
Originally Posted by No1Ford View Post
Does that move around at all? Or are you using a locking washer to keep it tight? It looks like it may move around, thats why i'm asking?
It moves with the motor. Does not shake as much as stock but it still moves.
machgsxr is offline   Reply With Quote
Old 04-12-2008, 11:44 PM   #135
machgsxr
Registered User
 
machgsxr's Avatar
 
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
Re: Eaton Swap.....

Quote:
Originally Posted by cveater View Post
how much did everything cost from installation stuff to the eaton.......
I ended up paying close to 2 for everything, but made alot of my money back selling stock parts, so in the end for me I actually came out even.

Quote:
Originally Posted by cre8787 View Post
Im right at $2,652 for everything but tune. I should be looking at $3,150 for the complete swap and tune. I came across a sweet deal, guy gave me everything down to the last bolt for $2,500. The only thing he didnt throw in was the throttle and crusie control cable. Even came with fuel tank/ pumps, a new alternator, and a JLT CAI.
Good price for all the parts.

Quote:
Originally Posted by cre8787 View Post
I noticed that you do not have the 3 EGR connectors that bracket to the drivers side of the Eaton. Are those connectors nesasary? Someone told me that you dont need them.
It can be deleted with the EGR delete that i did a long time ago. Those three sensors and the EGR are gone along with that big tube of vacuum wires. It looks so much cleaner without that stuff in there.
machgsxr is offline   Reply With Quote
Old 04-14-2008, 01:18 PM   #136
cre8787
Eaton Swapped Azure
 
cre8787's Avatar
 
Join Date: Mar 2008
Location: Germantown, Maryland
Posts: 246
Re: Eaton Swap.....

Thats good news, saves me a lot of hassel, thanks.
cre8787 is offline   Reply With Quote
Old 04-15-2008, 09:48 AM   #137
wcjr
Registered User
 
wcjr's Avatar
 
Join Date: Nov 2007
Location: Kentucky
Posts: 518
Re: Eaton Swap.....

if you leave the egr off doesnt fuel economy suffer...might not be the best idea for the dd mach owners doing this swap...
wcjr is offline   Reply With Quote
Old 05-11-2008, 12:00 AM   #138
TransAxle
Registered User
 
Join Date: Feb 2008
Location: Buford, GA
Posts: 332
Re: Eaton Swap.....

question! i know the swap list, is the list of ALL stock parts needed but, do some that come with aftermarket options, i.e. the TB, intake, maf, injectors, and headers, would not be needed to complete the swap?
__________________
2003 Torch Red Mach 1 - 5spd - C&L Inlet Pipe, K&N Drop in Intake, 85mm MAF, Diablo Predator Programmer, Pro5.0 Shifter, Spec Stage 2 Clutch, Steel Flywheel, Roys P&P Intake Manifold, Roys Intake Spacer, Magnaflow Tru-x X-Pipe, Magnaflow Magnapack Cat-Back, Tokico Gas Struts, Eibach Springs
TransAxle is offline   Reply With Quote
Old 05-14-2008, 04:09 PM   #139
cre8787
Eaton Swapped Azure
 
cre8787's Avatar
 
Join Date: Mar 2008
Location: Germantown, Maryland
Posts: 246
Re: Eaton Swap.....

Quote:
Originally Posted by TransAxle View Post
question! i know the swap list, is the list of ALL stock parts needed but, do some that come with aftermarket options, i.e. the TB, intake, maf, injectors, and headers, would not be needed to complete the swap?
You do not need new headers. I made the mistake of picking and chosing parts to buy off of the lists... do not underestamate the parts on the swap list. If you want to make a million trips to ford and to pep boys, buy them as they are needed. If you want to do it the right way, buy all the parts on the list plus valve cover gaskets and hose clamps. You will NOT use every singal part on that list because there are several different ways to install certain things. For example- some people chose to do an EGR delete; that alone takes of 2 or 3 parts from the list. Some people chose now to run all the evap stuff on the drivers side of the blower; that takes off 4 or 5 parts from the list.

The list is simply everything you need to make your swap like a stock cobra supercharger setup, not everything is needed to make it run on your car.

In my opinion, buy EVERY part machgsxr tells you to buy!!! Rather have five $20.00 parts and not need them than not have five $20.00 parts and need them.

BTW- Yes, you need new injectors. Yes, you need a new EGR valve and tube. Yes, you need new throttle and cruise control cables. Yes, you need a new IAC. No, you do not need a new throttle body. No, you do not need a new TPS.
Those were some of my questions... just thought I would answer them.

FYI- Plug the timing cover bolt hole that is not used on the new cobra timing cover to the right of ther water pump. Not doing this will result in an oil leak.
__________________
2003 Azure Blue Mach 1: M112 Eaton Supercharger (Unported/Stock Pullies/Stock Bottem End/Stock Heat Exchanger/Cobra Tank and Pumps) Pro 5.0, FRPP 4:10 Gears, Mac Catted H, SLP LMII, H&R Sport Springs, BFG KDW2 295's, SCT Custom Tune by Excessive Motorsports.

Dyno Results: 442hp; 386tq

Eaton Swap Pictures:
http://s28.photobucket.com/albums/c2.../Eaton%20Swap/

SOLD!
cre8787 is offline   Reply With Quote
Old 05-21-2008, 07:33 PM   #140
xXAzureMach1Xx
04 Mach 1
 
xXAzureMach1Xx's Avatar
 
Join Date: Mar 2008
Location: Pensacola FL
Posts: 272
Re: Eaton Swap.....

Will the stock computer with a tune work with the eaton swap?
xXAzureMach1Xx is offline   Reply With Quote
Old 05-21-2008, 08:13 PM   #141
Ran624
Registered User
 
Ran624's Avatar
 
Join Date: Jul 2004
Location: Sandiego Califorina
Posts: 56
Re: Eaton Swap.....

Yes the stock computer will work but you need it tuned by a pro..
Ran624 is offline   Reply With Quote
Old 05-21-2008, 11:07 PM   #142
TR04MACH
Registered User
 
Join Date: Dec 2005
Location: Herndon, VA
Posts: 541
Re: Eaton Swap.....

Quote:
Originally Posted by xXAzureMach1Xx View Post
Will the stock computer with a tune work with the eaton swap?
I would seriously doubt it would run well if at all on the stock mach tune but it might. Any tuner should be able to write you a quick safe tune that you could use to just drive it to the tuner as long as you've got a chip or handheld already. My tuner just wrote me a quick basic tune that was super safe so I could drive out there. I never had it over 3k but it gave me time to make sure my fluids were good and the coolant and power steering systems were burped etc. I put like 50 miles on it before I drove it to the tuner to make sure everything worked how it was supposed to.
__________________
2004 Torch Red Mach 1!
Eaton Swapped 8psi
SLP Longtube Headers
SLP Catted Shorty X
SLP Powerflo Catback
JLT RAI Intake
SCT Tune on 4bank chip
Nitto DR 275/40/17
MM Lower Control Arms
MM Urethane Rack Bushings
Hawk HPS Pads w/ MM brake lines
MM Full Length Subframes
Steeda Tri-ax
Sirius

For Sale!
TR04MACH is offline   Reply With Quote
Old 06-03-2008, 11:53 PM   #143
xXAzureMach1Xx
04 Mach 1
 
xXAzureMach1Xx's Avatar
 
Join Date: Mar 2008
Location: Pensacola FL
Posts: 272
Re: Eaton Swap.....

Dose anyone have a pic of the Cobra oil cooler adapter so i know what to look for thanks nick
xXAzureMach1Xx is offline   Reply With Quote
Old 06-04-2008, 12:20 AM   #144
Ran624
Registered User
 
Ran624's Avatar
 
Join Date: Jul 2004
Location: Sandiego Califorina
Posts: 56
Re: Eaton Swap.....

well my shaker is finally installed here are some picts Im still trying to figure out how to connect the innercooler pump though..
Attached Thumbnails
Mustang 003.jpg   Mustang 001.jpg   Mustang 005.jpg   Mustang 006.jpg  
Ran624 is offline   Reply With Quote
Old 06-05-2008, 07:06 PM   #145
xXAzureMach1Xx
04 Mach 1
 
xXAzureMach1Xx's Avatar
 
Join Date: Mar 2008
Location: Pensacola FL
Posts: 272
Re: Eaton Swap.....

Quote:
Originally Posted by xXAzureMach1Xx View Post
Dose anyone have a pic of the Cobra oil cooler adapter so i know what to look for thanks nick
Anyone?
xXAzureMach1Xx is offline   Reply With Quote
Old 06-05-2008, 07:28 PM   #146
machgsxr
Registered User
 
machgsxr's Avatar
 
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
Re: Eaton Swap.....

Quote:
Originally Posted by xXAzureMach1Xx View Post
Anyone?
taken from page 2....http://www.mach1registry.org/forums/...3&postcount=30
machgsxr is offline   Reply With Quote
Old 06-05-2008, 07:30 PM   #147
machgsxr
Registered User
 
machgsxr's Avatar
 
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
Re: Eaton Swap.....

Quote:
Originally Posted by Ran624 View Post
well my shaker is finally installed here are some picts Im still trying to figure out how to connect the innercooler pump though..
http://www.mach1registry.org/forums/...0&postcount=15

If you meant the routing of the hoses see this post.

If you meant to connect it to the car, then you either need some bolts and push them in from the backside of the holes or get with member Reloaded on here and ask him about the part # for some little collapse able nuts that work from Ford.
machgsxr is offline   Reply With Quote
Old 06-05-2008, 08:25 PM   #148
xXAzureMach1Xx
04 Mach 1
 
xXAzureMach1Xx's Avatar
 
Join Date: Mar 2008
Location: Pensacola FL
Posts: 272
Re: Eaton Swap.....

thanks dont know how i missed it
xXAzureMach1Xx is offline   Reply With Quote
Old 06-11-2008, 02:40 AM   #149
mkb116
Registered User
 
Join Date: Apr 2006
Location: Central California
Posts: 139
Re: Eaton Swap.....

Hey I am purchasing a complete swap kit from a guy and I was curious if anyone has done that? If so were there any parts that were missed because he will need the or whatnot. Also, how much does the factory harness need to be modified?
mkb116 is offline   Reply With Quote
Old 06-27-2008, 10:56 AM   #150
cre8787
Eaton Swapped Azure
 
cre8787's Avatar
 
Join Date: Mar 2008
Location: Germantown, Maryland
Posts: 246
Re: Eaton Swap.....

Every kit will be missing something... just the way it goes. You will need to modify the MAF sensor, alternator conector, and intercooler pump. all this is in this thread write up.
__________________
2003 Azure Blue Mach 1: M112 Eaton Supercharger (Unported/Stock Pullies/Stock Bottem End/Stock Heat Exchanger/Cobra Tank and Pumps) Pro 5.0, FRPP 4:10 Gears, Mac Catted H, SLP LMII, H&R Sport Springs, BFG KDW2 295's, SCT Custom Tune by Excessive Motorsports.

Dyno Results: 442hp; 386tq

Eaton Swap Pictures:
http://s28.photobucket.com/albums/c2.../Eaton%20Swap/

SOLD!
cre8787 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:31 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<