|
04-10-2009, 03:59 PM | #1 |
Established Lurker
Join Date: Mar 2006
Location: Selinsgrove Pa
Posts: 897
|
F*%$ing Bellhousing Bolts.
I need to remove the 3650 from my car to get it repaired. I have EVERYTHING done according to the Haynes/Chilton manual but cannot find the final bolt(s) I have found 5 so far. 3 on the driver side and 2 on the passengers side accessed from below. I think I'm missing a few at the top but how the hell do I get to them?? The trans was suppposed to be at the shop 10 minutes ago, but as long as I get it to them by sunday they can fit me in. This is the last thing I need to do so PLEASE give me some help/advice to get to the upper bolts.
Though searching the forums I found something about removing the exhaust headers (Not just the Xpipe), a motor mount and all sorts of emmsions equipment. Is this necissary?? Best I can see is on top I cant get to anything due to what looks like A/C or heater fittings on the firewall above the pass side cam cover.
__________________
My Rides '04 Screaming Yellow Mach 1 "Jennifer" Bassanni Catted X-Pipe, Catback, Hood Blackout, 315/35 BFG DR2s, AFS 17x10.5 Replicas, Professional Custom DiabloSport Tune, Stewart Warner UltraShift light, and XM Hardwire. 12.93 @ 107.24 '93 Nissan 240SX Convertible "Rei-Sen" Restored from Critically Damaged Frame, Lexus Pearl White Paint, Original Factory Tonneau |
04-10-2009, 04:04 PM | #2 |
#1052 of 9652
Join Date: Sep 2004
Location: sioux city iowa
Posts: 994
|
Re: F*%$ing Bellhousing Bolts.
You need a extension about a foot and a half long with a swivel Tape up the swivel so it doesn`t flop all over and come in from the back of the transmission. It also helps to lower the rear of the engine. P.S.. The two top bolts are super tight.
|
04-10-2009, 04:06 PM | #3 |
Established Lurker
Join Date: Mar 2006
Location: Selinsgrove Pa
Posts: 897
|
Re: F*%$ing Bellhousing Bolts.
Lower the engine? There are bolts on the top of the bellhousing right? Do I go after them from the top or bottom? I have 5 bolts out so far. How many are there total. That POS Haynes/Chiltons manual says "Remove Engine-to-Transmission Bolts" and then shows 5 bolts.
__________________
My Rides '04 Screaming Yellow Mach 1 "Jennifer" Bassanni Catted X-Pipe, Catback, Hood Blackout, 315/35 BFG DR2s, AFS 17x10.5 Replicas, Professional Custom DiabloSport Tune, Stewart Warner UltraShift light, and XM Hardwire. 12.93 @ 107.24 '93 Nissan 240SX Convertible "Rei-Sen" Restored from Critically Damaged Frame, Lexus Pearl White Paint, Original Factory Tonneau |
04-10-2009, 04:07 PM | #4 |
Registered User
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
|
Re: F*%$ing Bellhousing Bolts.
Loooong extension, swivel.
I found it easiest to get them from far back by where the mount is rather than trying to go straight down and get them off. Get a flashlight and you will see them if you look at it from by the tailshaft area. Hopefuly you can understand what im trying to say. lol EDIT: I removed all bolts from underneath the car. |
04-10-2009, 04:08 PM | #5 |
#1052 of 9652
Join Date: Sep 2004
Location: sioux city iowa
Posts: 994
|
Re: F*%$ing Bellhousing Bolts.
Cant remember how many bolts but i know there are two on top. Did you pull your starter. I also removed them all from under the car. You`ll probally bust a socket or two plus your go-nads on the two top bolts.
|
04-10-2009, 04:11 PM | #6 |
Established Lurker
Join Date: Mar 2006
Location: Selinsgrove Pa
Posts: 897
|
Re: F*%$ing Bellhousing Bolts.
Ok thanks guys. I feel like a **** tard. I am a better mechanic that this but god is this thing annoying....
__________________
My Rides '04 Screaming Yellow Mach 1 "Jennifer" Bassanni Catted X-Pipe, Catback, Hood Blackout, 315/35 BFG DR2s, AFS 17x10.5 Replicas, Professional Custom DiabloSport Tune, Stewart Warner UltraShift light, and XM Hardwire. 12.93 @ 107.24 '93 Nissan 240SX Convertible "Rei-Sen" Restored from Critically Damaged Frame, Lexus Pearl White Paint, Original Factory Tonneau |
04-10-2009, 08:55 PM | #7 |
Established Lurker
Join Date: Mar 2006
Location: Selinsgrove Pa
Posts: 897
|
Re: F*%$ing Bellhousing Bolts.
Had to buy a 20" extension, and add on an existing 10" plus a woble. Got one off, one more to go tomorrow.
BTW its good to be back on this site. Been so busy with my real project and its forums, that I kinda forgot to check here...
__________________
My Rides '04 Screaming Yellow Mach 1 "Jennifer" Bassanni Catted X-Pipe, Catback, Hood Blackout, 315/35 BFG DR2s, AFS 17x10.5 Replicas, Professional Custom DiabloSport Tune, Stewart Warner UltraShift light, and XM Hardwire. 12.93 @ 107.24 '93 Nissan 240SX Convertible "Rei-Sen" Restored from Critically Damaged Frame, Lexus Pearl White Paint, Original Factory Tonneau |
04-10-2009, 09:08 PM | #8 |
#1052 of 9652
Join Date: Sep 2004
Location: sioux city iowa
Posts: 994
|
Re: F*%$ing Bellhousing Bolts.
Glad to have you back
|
04-11-2009, 12:34 AM | #9 |
Established Lurker
Join Date: Mar 2006
Location: Selinsgrove Pa
Posts: 897
|
Re: F*%$ing Bellhousing Bolts.
Its nice to be back, too much time in Nissan land makes me want to drift my car around every turn and learn Japanese....
__________________
My Rides '04 Screaming Yellow Mach 1 "Jennifer" Bassanni Catted X-Pipe, Catback, Hood Blackout, 315/35 BFG DR2s, AFS 17x10.5 Replicas, Professional Custom DiabloSport Tune, Stewart Warner UltraShift light, and XM Hardwire. 12.93 @ 107.24 '93 Nissan 240SX Convertible "Rei-Sen" Restored from Critically Damaged Frame, Lexus Pearl White Paint, Original Factory Tonneau |
04-11-2009, 03:43 AM | #10 |
Blue Mach 1 Owner
Join Date: Dec 2002
Location: Midwest Pony Express Land
Posts: 892
|
Re: F*%$ing Bellhousing Bolts.
I use a small bottle jack on one of front the oil pan bolts to push up on the front of the engine till it just starts to lift the front end of the mach a little which will make the tail shaft of the tranny come down so you have much better access to get at those top bolts and every little bit helps.
__________________
Do You Think I Like Blue ? 2014 Blue Stang GT Convertible with White strips 5.0 6 Speed Automatic Wife Daily Driver/Toy 2013 Stang GT 5.0 Grabber Blue 6 Spd Son's Daily Driver/Street Drag Car 2004 Blue Mach 1 4.6 32V 5 Spd R Code Factory Shaker My New Toy 1999 Blue Stang - 4.6 16V 4 Spd Auto GT Daughters Daily Driver 1990 Blue Stang 351W 5 Spd Son's Drag Strip Only Car 1969 Blue Mach 1 428CJ R Code 4Spd My Original Toy SOLD Blue Is The Fastest |
04-11-2009, 11:08 AM | #11 |
Mach Underhood
Join Date: Jan 2007
Location: FL
Posts: 1,677
|
Re: F*%$ing Bellhousing Bolts.
Engine mounts lose, tranny crossmember unbolted, jack the front of the engine up.....and you have tons of access.
I always remove the top 2 first....as they are able to be broken lose, then removed with your hands....without binding up due to them being the last bolts removed. If working on a floor, I have always found it easy to actually lay with your feet towards the rear of the car, on your back, with your head under the oilpan......and "bearhug" the transmission to install/remove the bolts by hand.
__________________
Stock 4.6 4V, Cobra Cammed: 11.63@117.84 - N/A T45 / 4.56 / Drag Radials - N/A 4V Video |
04-11-2009, 12:57 PM | #12 |
Established Lurker
Join Date: Mar 2006
Location: Selinsgrove Pa
Posts: 897
|
Re: F*%$ing Bellhousing Bolts.
It's out!! On the way to the shop to be repaired. I swear I'm getting a TKO next time this dies.
__________________
My Rides '04 Screaming Yellow Mach 1 "Jennifer" Bassanni Catted X-Pipe, Catback, Hood Blackout, 315/35 BFG DR2s, AFS 17x10.5 Replicas, Professional Custom DiabloSport Tune, Stewart Warner UltraShift light, and XM Hardwire. 12.93 @ 107.24 '93 Nissan 240SX Convertible "Rei-Sen" Restored from Critically Damaged Frame, Lexus Pearl White Paint, Original Factory Tonneau |
04-11-2009, 05:38 PM | #13 |
Registered User
Join Date: Apr 2005
Location: Norfolk, Virginia
Posts: 1,131
|
Re: F*%$ing Bellhousing Bolts.
I'll feel your pain. The 1st time my clutch went out I was pulling the thing in a friends drive way in off and on rain with temps in the high 30's.
I have to do it again to, #$%*!! |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|