2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Power Adders

Power Adders Superchargers, Turbos, Nitrous, etc...

Reply
 
Thread Tools Display Modes
Old 04-01-2009, 11:34 PM   #226
eatonmach1
Registered User
 
eatonmach1's Avatar
 
Join Date: Oct 2007
Location: Pikeville, KY
Posts: 524
Re: Eaton Swap.....

Quote:
Originally Posted by xXAzureMach1Xx View Post
Can some one tell me what three radiator hose is need for the swap? i know the part numbers but i need to know where they go to. One is the upper radaitor to cross over tube but dont know the other two
I know one of the others hooks to the middle of the crossover tube then goes down to the thermostat housing. It is a longer hose. I would guess the thrid one goes from the thermostat housing to the oil cooler on the side of the engine. Thats what I just hooked up on my eaton swap.
__________________
2003 Black 5 Speed

3.73's PRO 50 Shifter,
Aluminum Driveshaft


2003 Ox White Cobra

3.2 Pulley
Pro 50 Shifter
Sticky Nittos
What else do ya need :ORANGE:
eatonmach1 is offline   Reply With Quote
Old 04-02-2009, 12:16 PM   #227
xXAzureMach1Xx
04 Mach 1
 
xXAzureMach1Xx's Avatar
 
Join Date: Mar 2008
Location: Pensacola FL
Posts: 272
Re: Eaton Swap.....

Quote:
Originally Posted by eatonmach1 View Post
I know one of the others hooks to the middle of the crossover tube then goes down to the thermostat housing. It is a longer hose. I would guess the thrid one goes from the thermostat housing to the oil cooler on the side of the engine. Thats what I just hooked up on my eaton swap.
After reading your post it hit me about the oil cooler one
xXAzureMach1Xx is offline   Reply With Quote
Old 04-02-2009, 01:20 PM   #228
eatonmach1
Registered User
 
eatonmach1's Avatar
 
Join Date: Oct 2007
Location: Pikeville, KY
Posts: 524
Re: Eaton Swap.....

Quote:
Originally Posted by xXAzureMach1Xx View Post
After reading your post it hit me about the oil cooler one
Their are a lota thing going on with the eaton swap it can get confusing fast! I have just been dividing the system up and working on one part at a time. I almost have mine done except a few cooling tubes. I got those ordered yesterday so I should get them today. Next is the wiring stuff
__________________
2003 Black 5 Speed

3.73's PRO 50 Shifter,
Aluminum Driveshaft


2003 Ox White Cobra

3.2 Pulley
Pro 50 Shifter
Sticky Nittos
What else do ya need :ORANGE:
eatonmach1 is offline   Reply With Quote
Old 04-05-2009, 12:51 AM   #229
Mustang92
Registered User
 
Mustang92's Avatar
 
Join Date: Apr 2008
Location: South Florida
Posts: 238
Re: Eaton Swap.....

Making pretty good progress on mine. Started last Monday and been working on it an hour or two a night. Other than a few unexpected things it's been going pretty smoothly. I need to pick up new belts tomorrow and Monday I need to order a new o-ring for the oil pump cooler shaft, mine was pretty beat up and I need to find injector adapters for my 60s.



I'm in no rush though, I'm aiming to get it to the dyno a week from Monday.

Bill
__________________
2004 Mach 1 Comp Org - SOLD
1994 Mustang LS Swap - 11.40 @ 117.88 NA / 9.85 @ 134.74 N2O
Mustang92 is offline   Reply With Quote
Old 04-05-2009, 05:06 PM   #230
xXAzureMach1Xx
04 Mach 1
 
xXAzureMach1Xx's Avatar
 
Join Date: Mar 2008
Location: Pensacola FL
Posts: 272
Re: Eaton Swap.....

on the list i have it say i need the sensor on the back of the S/C. can someone tell me what it is or have a pic? Is the IAC Valve the same from the mach 1 to the cobra?
xXAzureMach1Xx is offline   Reply With Quote
Old 04-05-2009, 05:59 PM   #231
Mustang92
Registered User
 
Mustang92's Avatar
 
Join Date: Apr 2008
Location: South Florida
Posts: 238
Re: Eaton Swap.....

IAC is on top of the plenum, the sensor on the back of the Eaton is the IAT2 sensor.
__________________
2004 Mach 1 Comp Org - SOLD
1994 Mustang LS Swap - 11.40 @ 117.88 NA / 9.85 @ 134.74 N2O
Mustang92 is offline   Reply With Quote
Old 04-05-2009, 06:07 PM   #232
xXAzureMach1Xx
04 Mach 1
 
xXAzureMach1Xx's Avatar
 
Join Date: Mar 2008
Location: Pensacola FL
Posts: 272
Re: Eaton Swap.....

Is the IAC Valve the same from a mach to a cobra
xXAzureMach1Xx is offline   Reply With Quote
Old 04-05-2009, 07:11 PM   #233
Mustang92
Registered User
 
Mustang92's Avatar
 
Join Date: Apr 2008
Location: South Florida
Posts: 238
Re: Eaton Swap.....

It should be the same. I'm reusing mine.
__________________
2004 Mach 1 Comp Org - SOLD
1994 Mustang LS Swap - 11.40 @ 117.88 NA / 9.85 @ 134.74 N2O
Mustang92 is offline   Reply With Quote
Old 04-05-2009, 07:17 PM   #234
nickster
certified MACH 1 nut
 
nickster's Avatar
 
Join Date: Apr 2004
Location: nova scotia canada
Posts: 1,520
Re: Eaton Swap.....

plugin is at a different angle only dif.
__________________
shm stage 2 cams,dynomax longtubes,2 3/4 h pipe homemade,excal2,wideband commander,proracers package,60#injectors,2400 mas air,eaton,forged motor,4# metco ring,1 of a kind pully bridge,and great #s on a stock eaton 476.88rwhp-451.74rwtq
nickster is offline   Reply With Quote
Old 04-05-2009, 08:31 PM   #235
eatonmach1
Registered User
 
eatonmach1's Avatar
 
Join Date: Oct 2007
Location: Pikeville, KY
Posts: 524
Re: Eaton Swap.....

Just got mine done and it runs great! Like stock drivability! I will post some pics tomorrow. If you guys need any help if connections ect let me know I will get pics.
__________________
2003 Black 5 Speed

3.73's PRO 50 Shifter,
Aluminum Driveshaft


2003 Ox White Cobra

3.2 Pulley
Pro 50 Shifter
Sticky Nittos
What else do ya need :ORANGE:
eatonmach1 is offline   Reply With Quote
Old 04-05-2009, 11:59 PM   #236
eatonmach1
Registered User
 
eatonmach1's Avatar
 
Join Date: Oct 2007
Location: Pikeville, KY
Posts: 524
Re: Eaton Swap.....

Quote:
Originally Posted by Mustang92 View Post
Making pretty good progress on mine. Started last Monday and been working on it an hour or two a night. Other than a few unexpected things it's been going pretty smoothly. I need to pick up new belts tomorrow and Monday I need to order a new o-ring for the oil pump cooler shaft, mine was pretty beat up and I need to find injector adapters for my 60s.



I'm in no rush though, I'm aiming to get it to the dyno a week from Monday.

Bill

Should have got ya some EV6 ones Looks good! Gota luv the clean look of the eaton. Almost forgot to tell ya don't forget the coolant tube bolts before you put the eaton on its a PITA to get them on if you do.
__________________
2003 Black 5 Speed

3.73's PRO 50 Shifter,
Aluminum Driveshaft


2003 Ox White Cobra

3.2 Pulley
Pro 50 Shifter
Sticky Nittos
What else do ya need :ORANGE:

Last edited by eatonmach1; 04-06-2009 at 12:16 AM.
eatonmach1 is offline   Reply With Quote
Old 04-06-2009, 12:13 AM   #237
eatonmach1
Registered User
 
eatonmach1's Avatar
 
Join Date: Oct 2007
Location: Pikeville, KY
Posts: 524
Re: Eaton Swap.....

Here are a couple of pics of mine. I have to clean my engine compartment up again but besides that I am almost done.
Attached Thumbnails
DSC01257.jpg   DSC01258.jpg   DSC01259.jpg   DSC01260.jpg   DSC01261.jpg  

__________________
2003 Black 5 Speed

3.73's PRO 50 Shifter,
Aluminum Driveshaft


2003 Ox White Cobra

3.2 Pulley
Pro 50 Shifter
Sticky Nittos
What else do ya need :ORANGE:
eatonmach1 is offline   Reply With Quote
Old 04-06-2009, 12:15 AM   #238
eatonmach1
Registered User
 
eatonmach1's Avatar
 
Join Date: Oct 2007
Location: Pikeville, KY
Posts: 524
Re: Eaton Swap.....

A few more.
Attached Thumbnails
DSC01263.jpg   DSC01264.jpg   DSC01265.jpg  
__________________
2003 Black 5 Speed

3.73's PRO 50 Shifter,
Aluminum Driveshaft


2003 Ox White Cobra

3.2 Pulley
Pro 50 Shifter
Sticky Nittos
What else do ya need :ORANGE:
eatonmach1 is offline   Reply With Quote
Old 04-06-2009, 07:13 AM   #239
Mustang92
Registered User
 
Mustang92's Avatar
 
Join Date: Apr 2008
Location: South Florida
Posts: 238
Re: Eaton Swap.....

Quote:
Originally Posted by eatonmach1 View Post
Should have got ya some EV6 ones Looks good! Gota luv the clean look of the eaton. Almost forgot to tell ya don't forget the coolant tube bolts before you put the eaton on its a PITA to get them on if you do.
I can't complain the 60's I got were free. The top coolant crossover tube bolts are in just not the front ones in that picture. I got a little further on mine but ran into a few other issues. I'm missing the upper alternator bolt and the lower alternator bracket I have was cut so the bottom ear is missing.
__________________
2004 Mach 1 Comp Org - SOLD
1994 Mustang LS Swap - 11.40 @ 117.88 NA / 9.85 @ 134.74 N2O
Mustang92 is offline   Reply With Quote
Old 04-06-2009, 12:47 PM   #240
eatonmach1
Registered User
 
eatonmach1's Avatar
 
Join Date: Oct 2007
Location: Pikeville, KY
Posts: 524
Re: Eaton Swap.....

Quote:
Originally Posted by Mustang92 View Post
I can't complain the 60's I got were free. The top coolant crossover tube bolts are in just not the front ones in that picture. I got a little further on mine but ran into a few other issues. I'm missing the upper alternator bolt and the lower alternator bracket I have was cut so the bottom ear is missing.
Can't Complain about free The upper altenator bolt is in the help parts section at advance auto parts believe it or not. I had to go to a CAT dealer to get longer metric bolts here. Not a lot of places here seem to carry a large stock of metric bolts. That really sucks about the lower alternator bracket. The ear thats missing is it the one that bolts the 8 rib setup to the bracket?
__________________
2003 Black 5 Speed

3.73's PRO 50 Shifter,
Aluminum Driveshaft


2003 Ox White Cobra

3.2 Pulley
Pro 50 Shifter
Sticky Nittos
What else do ya need :ORANGE:
eatonmach1 is offline   Reply With Quote
Old 04-06-2009, 04:18 PM   #241
xXAzureMach1Xx
04 Mach 1
 
xXAzureMach1Xx's Avatar
 
Join Date: Mar 2008
Location: Pensacola FL
Posts: 272
Re: Eaton Swap.....

i should be able to fit a 1/4 intake spacer right?
xXAzureMach1Xx is offline   Reply With Quote
Old 04-06-2009, 06:40 PM   #242
nickster
certified MACH 1 nut
 
nickster's Avatar
 
Join Date: Apr 2004
Location: nova scotia canada
Posts: 1,520
Re: Eaton Swap.....

still waiting for intercooler pump, so i dropped the tank and modded the fuel hat for twin gt pumps
__________________
shm stage 2 cams,dynomax longtubes,2 3/4 h pipe homemade,excal2,wideband commander,proracers package,60#injectors,2400 mas air,eaton,forged motor,4# metco ring,1 of a kind pully bridge,and great #s on a stock eaton 476.88rwhp-451.74rwtq
nickster is offline   Reply With Quote
Old 04-06-2009, 08:05 PM   #243
Mustang92
Registered User
 
Mustang92's Avatar
 
Join Date: Apr 2008
Location: South Florida
Posts: 238
Re: Eaton Swap.....

Quote:
Originally Posted by eatonmach1 View Post
Can't Complain about free The upper altenator bolt is in the help parts section at advance auto parts believe it or not. I had to go to a CAT dealer to get longer metric bolts here. Not a lot of places here seem to carry a large stock of metric bolts. That really sucks about the lower alternator bracket. The ear thats missing is it the one that bolts the 8 rib setup to the bracket?
Yeah the one missing bolts to the pulley cage. Luckily that bracket was only $26 from the dealer and they had the bolt as well. I did strike out on the O-ring for the oil cooler shaft. Mine was messed up and Ford doesn't sell it separate, you have to buy the entire shaft for $50. Normal O-rings are too thick but I found a water faucet valve with a thinner O-ring that worked for much less.

Bill
__________________
2004 Mach 1 Comp Org - SOLD
1994 Mustang LS Swap - 11.40 @ 117.88 NA / 9.85 @ 134.74 N2O
Mustang92 is offline   Reply With Quote
Old 04-06-2009, 10:59 PM   #244
03Steve
Registered User
 
03Steve's Avatar
 
Join Date: Dec 2004
Location: St. Louis, MO
Posts: 298
Re: Eaton Swap.....

Count me in...with a 99 Cobra. Just disassembled everything last week. Engine is out, and all of my 99 Cobra components are for sale.

Doing more of a "race" setup; twin screw, intercooler resevoir in the trunk, aftermarket cooling lines, no EGR or EVAP, etc. I'll post as progress begins.
__________________
2003 Cobra Coupe SOLD
WFC8 #7 Heads Up Qualifier - Cobra Eliminator
MSC3 #1 Heads Up Qualifier - Fastest Ford Vehicle

Saleen Clone CURRENT
-10.7:1 Compression and 2.3L Whipple
-Comp Cams 106360 cams @ 108LSA
-4R70W and CVAF1 Auto EEC
-96 Cobra Rear End
-Machine/Head work by Todd Fays of Phase 2 Crestwood, MO

http://i79.photobucket.com/albums/j1...unch2small.jpg
03Steve is offline   Reply With Quote
Old 04-07-2009, 01:10 AM   #245
eatonmach1
Registered User
 
eatonmach1's Avatar
 
Join Date: Oct 2007
Location: Pikeville, KY
Posts: 524
Re: Eaton Swap.....

Quote:
Originally Posted by xXAzureMach1Xx View Post
i should be able to fit a 1/4 intake spacer right?
I think so I tested my hood have about 2 inches of clearance. May cause problems with the shaker.
__________________
2003 Black 5 Speed

3.73's PRO 50 Shifter,
Aluminum Driveshaft


2003 Ox White Cobra

3.2 Pulley
Pro 50 Shifter
Sticky Nittos
What else do ya need :ORANGE:
eatonmach1 is offline   Reply With Quote
Old 04-07-2009, 07:44 AM   #246
nickster
certified MACH 1 nut
 
nickster's Avatar
 
Join Date: Apr 2004
Location: nova scotia canada
Posts: 1,520
Re: Eaton Swap.....

Quote:
Originally Posted by 03Steve View Post
Count me in...with a 99 Cobra. Just disassembled everything last week. Engine is out, and all of my 99 Cobra components are for sale.

Doing more of a "race" setup; twin screw, intercooler resevoir in the trunk, aftermarket cooling lines, no EGR or EVAP, etc. I'll post as progress begins.
nice pic you have there
__________________
shm stage 2 cams,dynomax longtubes,2 3/4 h pipe homemade,excal2,wideband commander,proracers package,60#injectors,2400 mas air,eaton,forged motor,4# metco ring,1 of a kind pully bridge,and great #s on a stock eaton 476.88rwhp-451.74rwtq
nickster is offline   Reply With Quote
Old 04-17-2009, 04:59 PM   #247
el virus
Registered User
 
el virus's Avatar
 
Join Date: Nov 2008
Location: orlando,fl
Posts: 142
Re: Eaton Swap.....

I am currently collecting parts to start my eaton swap and I ran into an 03-04cobra ecu and was wondering if any of you guys run the cobra computer or if it doesn't really matter what you use.
__________________
O/R x-pipe, 1/2 inch spacer, 03-04 cobra chrome wheels 10.5/rear 9/front, flowmaster catback, aem wideband, 03-04 front and rear cobra bumper.

soon to be f/i d1sc
el virus is offline   Reply With Quote
Old 04-17-2009, 06:51 PM   #248
nickster
certified MACH 1 nut
 
nickster's Avatar
 
Join Date: Apr 2004
Location: nova scotia canada
Posts: 1,520
Re: Eaton Swap.....

most run the stock with a tune
__________________
shm stage 2 cams,dynomax longtubes,2 3/4 h pipe homemade,excal2,wideband commander,proracers package,60#injectors,2400 mas air,eaton,forged motor,4# metco ring,1 of a kind pully bridge,and great #s on a stock eaton 476.88rwhp-451.74rwtq
nickster is offline   Reply With Quote
Old 04-19-2009, 12:54 AM   #249
Mustang92
Registered User
 
Mustang92's Avatar
 
Join Date: Apr 2008
Location: South Florida
Posts: 238
Re: Eaton Swap.....

Can anyone clarify something for me about the alternator wiring. I thought I did it right but read something earlier that has me questioning it.

I took the factory plug and the new plug and basically oriented them so that the clip was on the top (the release clip) and then swapped over the two outside wires.

In one of the write ups it was stated they should be reversed. Of course the pigtail from Ford is all black wiring so it's not like I could even attempt to match wires from the two.

Also what did everyone do for the return spring on the throttle body? From what I could see most left it off.

I finally got the last few things I needed. I have to still take care of the IAT2 plug, figure out the vacuum lines (without EGR and related sensors), build my dual FPDM harness and drop in the GT pumps.

Bill
__________________
2004 Mach 1 Comp Org - SOLD
1994 Mustang LS Swap - 11.40 @ 117.88 NA / 9.85 @ 134.74 N2O
Mustang92 is offline   Reply With Quote
Old 04-23-2009, 08:58 PM   #250
xXAzureMach1Xx
04 Mach 1
 
xXAzureMach1Xx's Avatar
 
Join Date: Mar 2008
Location: Pensacola FL
Posts: 272
Re: Eaton Swap.....

The guy at the dealer told me to just cut my plug and extend it. He said it was the same plug.
xXAzureMach1Xx is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:30 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<