2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Power Adders

Power Adders Superchargers, Turbos, Nitrous, etc...

Reply
 
Thread Tools Display Modes
Old 09-05-2012, 10:28 AM   #51
gonemad
Registered User
 
gonemad's Avatar
 
Join Date: Oct 2010
Location: thompson oh
Posts: 333
Re: Official Nitrous HP/TQ/mods thread

Stock bottom end: YES

Nitrous Kit Brand Used: NX WET SHARK NOZZLE

Other Nitrous Add On's: Heater, purge, window switch

Nitrous Shot: 150

Where Does Nitrous Spray At: 4/5 INCHES IN FRONT OF TB

Fuel system: Stock

Tuner/Dyno shop info: Don LaSota

Other notable mods: Long tubes, Ported stock runner intake, 98 cobra intake cams,full 3" exhaust, TKO 500, 4.30 gear,

RWHP/RWTQ: N/A

BEST 1/4 mile: 10.89@125
__________________
2004 comp orange, cobra cams, kooks LTs, cobra diff, 31 spline moser, 4.30s, TKO500 promotion clutch/fly, FMS driveshaft, JLT CAI, na svt ported intake, UPR adj rear Team Z front, full 3" magnaflow X and catback. 11.97@115 n/a 10.89@125 on 150 shot.
89 coupe stock bottom end on3 70mm. 10.02@134

Last edited by gonemad; 02-26-2015 at 10:09 AM.
gonemad is offline   Reply With Quote
Old 09-12-2012, 09:06 PM   #52
Bmackfsu
Registered User
 
Bmackfsu's Avatar
 
Join Date: Sep 2011
Location: Casselberry, Florida
Posts: 5
Re: Official Nitrous HP/TQ/mods thread

If you have a 2 stage kit with a 50hp shot per stage, then technically you are running 100hp shot, correct? Specifically a compucar setup with .037N & .026G jets for each stage?
Bmackfsu is offline   Reply With Quote
Old 09-29-2012, 10:28 PM   #53
ScreamingMach46
Registered User
 
ScreamingMach46's Avatar
 
Join Date: Dec 2008
Location: Chicago, IL
Posts: 907
Re: Offical Nitrous numbers thread

Quote:
Originally Posted by ScreamingMach46 View Post
Stock bottom end: YES

Nitrous Kit Brand: NX

Safety Features/Add-ons: Nitrous Outlet digital window switch/WOT switch, custom cupholder switch panel, NOS bottle heater, ZEX fuel rail adaptor, AEM Wideband

Nitrous/Fuel Jet Size and HP shot: Nitrous Jet-.052 / Fuel Jet-.033 -- 100shot

Fuel system: SVT Focus pump

Tuner/Tuned By: Xcal3 tuned by Tim Barth at Modular Powerhouse / Mr. Norms Garage (93 octane & race gas tune)

Other notable mods: JLT intake, BBK LTs, BBK O/R x-pipe, Mac Catback

N/A RWHP/RWTQ: 307rwhp 328rwtq

Nitrous RWHP/RWTQ: 380rwhp 487rwtq (only 900psi)

N/A Track Times: 12.7 @ 107 (1.70)

Nitrous Track Times: 12.09 @ 110 (1.64)

Just ran a 12.09 @ 110 (1.64) thursday night. Soooooo close to 11s! Couldn't get the trans to go into 2nd the rest of the night
__________________
2004 Mach 1 - Screaming Yellow - 5 speed - IUP - 1 of 624
Full Bolt-ons, Built Rear, NX 100 shot, tune by Tim Barth @ MPH
N/A - 12.7 @ 107 (1.70)
N2O - 380rwhp 487rwtq
12.03 @ 110 (1.55)

SOLD

2004 Cobra - Screaming Yellow - T56 - 1 of 299
KB 2.8H @ 20lbs, 98 Intake Cams, E85, Tune by Tim Barth @ MPH
711rwhp 635rwtq
ScreamingMach46 is offline   Reply With Quote
Old 10-05-2012, 10:10 AM   #54
gonemad
Registered User
 
gonemad's Avatar
 
Join Date: Oct 2010
Location: thompson oh
Posts: 333
Re: Offical Nitrous numbers thread

Quote:
Originally Posted by ScreamingMach46 View Post
Just ran a 12.09 @ 110 (1.64) thursday night. Soooooo close to 11s! Couldn't get the trans to go into 2nd the rest of the night
Hey check out my post above you, i have a nearly identical set of mods as you but im 10mph faster, and your only picking up 3 mph with nitrous? Something is askew for sure. I run 109-111 n/a depending on d/a and i pick up a full 10 mph on the bottle. We have the same system too, i do run it at 1050 psi but it only picks up about 1mph over 900 (NX is designed to run 1000-1100 btw) ill have to check my jets to see if we are the same.

Ive never dynoed the car but I think im in the 320 rwhp range n/a and 410/500 on bottle wich is really close to you. PM me for my # if you wanna dicsuss a bit further, ive been playing with nitrous for a while and know my way around it a bit.
__________________
2004 comp orange, cobra cams, kooks LTs, cobra diff, 31 spline moser, 4.30s, TKO500 promotion clutch/fly, FMS driveshaft, JLT CAI, na svt ported intake, UPR adj rear Team Z front, full 3" magnaflow X and catback. 11.97@115 n/a 10.89@125 on 150 shot.
89 coupe stock bottom end on3 70mm. 10.02@134
gonemad is offline   Reply With Quote
Old 10-06-2012, 10:23 PM   #55
ScreamingMach46
Registered User
 
ScreamingMach46's Avatar
 
Join Date: Dec 2008
Location: Chicago, IL
Posts: 907
Re: Offical Nitrous numbers thread

Yeah, I have no idea how I'm only trapping 110. The 107 N/A was with the 3.55s I've yet to make a pass off the bottle with the 4.10s.

I typically run it around 1000psi.

Might go this Thursday or next Thursday and put some race gas in it and pull the seats out.
__________________
2004 Mach 1 - Screaming Yellow - 5 speed - IUP - 1 of 624
Full Bolt-ons, Built Rear, NX 100 shot, tune by Tim Barth @ MPH
N/A - 12.7 @ 107 (1.70)
N2O - 380rwhp 487rwtq
12.03 @ 110 (1.55)

SOLD

2004 Cobra - Screaming Yellow - T56 - 1 of 299
KB 2.8H @ 20lbs, 98 Intake Cams, E85, Tune by Tim Barth @ MPH
711rwhp 635rwtq
ScreamingMach46 is offline   Reply With Quote
Old 02-04-2013, 02:37 PM   #56
stangpainter
Registered User
 
stangpainter's Avatar
 
Join Date: May 2012
Location: attalla,al
Posts: 160
Re: Official Nitrous HP/TQ/mods thread

Ok mach guru's,. Need your advice. My 03 mach has 70k on the clock,and has lived a pretty babied life,..i do run it occasionally, and my best time is a 12.80 in 1/4. The engine is stock except for cai, off road x, magnaflo exhaust, 4.10's,sct tune and 315/35 drag radials. So heres the question: I'd like to put 100 shot on this car, as it seems to be the best bang for my budget, in your opinion would you do-it,..? If yes which way would you go,wet or dry,..this would be done strictly for the friday nite track trips,.and it only gets ran a couple time a month. I know hindsite is 20/20,..so please give some insight on your hindsight..thanks
__________________
***STEVEN***
stangpainter is offline   Reply With Quote
Old 02-16-2013, 06:59 PM   #57
a_bishop07
Registered User
 
a_bishop07's Avatar
 
Join Date: Apr 2011
Location: Grain Valley, MO
Posts: 67
Re: Official Nitrous HP/TQ/mods thread

Stock bottom end: YES

Nitrous Kit Brand Used: ZEX WET KIT WITH NANO

Other Nitrous Add On's: NANO, purge

Nitrous Shot: 125 WET

Where Does Nitrous Spray At: INNER ELBOW OF INTAKE TUBE 3 INCHES FROM TB

Fuel system: Stock

Tuner/Dyno shop info: The Tuning Station Blue Springs, MO/
Tuner- Justune

Other notable mods: Long tubes, 98 cobra intake cams,full 2.5" exhaust xpipe, 4.10 gear, 17" ET street bias

RWHP/RWTQ: 479whp/560wtq

BEST 1/4 mile: dont know yet

http://youtu.be/6xPMMSXCdSc
__________________
JLT cai, mac LT headers and off road x, borla catback, 4.10 gears, 98 cobra cams, 125 wet shot
a_bishop07 is offline   Reply With Quote
Old 02-16-2013, 07:03 PM   #58
Flash88
Registered User
 
Join Date: Jul 2011
Location: jacksonville
Posts: 664
Re: Official Nitrous HP/TQ/mods thread

****. is it the NANO that gives the nitrous its extra kick? cause my numbers were 312/320 n/a and 410/450 with a 100 shot
__________________
___________________________
70mm single turbo.
Flash88 is offline   Reply With Quote
Old 02-16-2013, 07:25 PM   #59
a_bishop07
Registered User
 
a_bishop07's Avatar
 
Join Date: Apr 2011
Location: Grain Valley, MO
Posts: 67
Re: Official Nitrous HP/TQ/mods thread

well it was a full bottle with a high flow valve and the nano just keeps the pressure at 1100psi. its about 40* today so it had really cool air also.
__________________
JLT cai, mac LT headers and off road x, borla catback, 4.10 gears, 98 cobra cams, 125 wet shot
a_bishop07 is offline   Reply With Quote
Old 02-16-2013, 09:14 PM   #60
Flash88
Registered User
 
Join Date: Jul 2011
Location: jacksonville
Posts: 664
Re: Official Nitrous HP/TQ/mods thread

**** man, without the graph and stuff i would call ********. but thats some impressive numbers pretty much made as much power as my ported eaton, but with more torque.
__________________
___________________________
70mm single turbo.
Flash88 is offline   Reply With Quote
Old 02-17-2013, 12:14 PM   #61
a_bishop07
Registered User
 
a_bishop07's Avatar
 
Join Date: Apr 2011
Location: Grain Valley, MO
Posts: 67
Re: Official Nitrous HP/TQ/mods thread

from 40 i put atleast a full car if not more on a 500+hp cobra with a ported and pullied blower. its on my youtube page. baad2003mach1. but as u can see on the graph the torque is very short lived at 560. id say its closer to 500tq through out most of the dyno chart.
__________________
JLT cai, mac LT headers and off road x, borla catback, 4.10 gears, 98 cobra cams, 125 wet shot
a_bishop07 is offline   Reply With Quote
Old 02-17-2013, 02:57 PM   #62
Flash88
Registered User
 
Join Date: Jul 2011
Location: jacksonville
Posts: 664
Re: Official Nitrous HP/TQ/mods thread

nice vids! car def rides out. Making a good name for machs! haha
__________________
___________________________
70mm single turbo.
Flash88 is offline   Reply With Quote
Old 02-17-2013, 03:37 PM   #63
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,005
Re: Official Nitrous HP/TQ/mods thread

I especially liked the comment of the gto owner after you walked him. LOL.

Strong car! Stock trans still?
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁
311-420 is offline   Reply With Quote
Old 03-14-2013, 08:35 AM   #64
OWmach1
Registered User
 
OWmach1's Avatar
 
Join Date: Aug 2012
Location: CA
Posts: 452
Re: Official Nitrous HP/TQ/mods thread

So pretty much my power adders will be: JLT rai, catted Mac h-pipe, cat back, upper intake spacer.

All I need is colder plugs for a 75 wet NX kit? I'm just a bit concerned on the shity gas we get here in Cali. I'm assuming a tune would make the car run better and I should get the sct chip so i can switch off from valet to NA tune and one for nitrous?
OWmach1 is offline   Reply With Quote
Old 03-19-2013, 06:14 AM   #65
medicmatt
S F F D
 
medicmatt's Avatar
 
Join Date: Dec 2003
Location: San Francisco, CA.
Posts: 503
Re: Official Nitrous HP/TQ/mods thread

Do/did any of you NX people have a strut tower brace? If so, did it get in the way or did your nitrous kit (NX EFI single nozzle kit SKU #20922-10) fit without having to remove/relocate the brace or hood scoop or various other stuff and things?
Thanks
Matt
__________________
04 BLACK /W IUP
BUILD DATE 10/13/2003
Mods
Some black stuff.
http://www.mach1registry.org/photopo...rt=1&cat=500&p
medicmatt is offline   Reply With Quote
Old 04-27-2013, 09:44 PM   #66
uscstew
Registered User
 
uscstew's Avatar
 
Join Date: Mar 2009
Location: Greer, SC
Posts: 420
Re: Official Nitrous HP/TQ/mods thread

Stock bottom end: No (Manley flat tops, Manley h beams, total seal rings)

Nitours Kit Brand: NX wet, and nx dry (pre Maf)

Safety Features/Add-ons: Window switch, dedicated fuels

Fuel system:39lb injectors, gt pump in the car. And a dedicated fuel system for the wet shot

Tuner/Tuned By: Xcal 2

Other notable mods: ported intake, 97 cobra cams, 1 3/4 mid lengths and 3" exhaust, most bolt ons

N/A RWHP/RWTQ: 352/351

Nitrous RWHP/RWTQ: 609/680
uscstew is offline   Reply With Quote
Old 06-28-2013, 06:19 PM   #67
boss_pc2
Registered User
 
boss_pc2's Avatar
 
Join Date: Mar 2012
Location: Sherwood,AR/Victoria, TX
Posts: 86
Stock bottom end: yes



Nitrous Kit Brand Used: zex



Other Nitrous Add On's: purge, bottle heater and SOS console controller



Nitrous Shot: 125



Where Does Nitrous Spray At: 7" from tb



Fuel system: focus pump, 39lb injectors



Tuner/Dyno shop info: Shawn@Lethal performance in SATX



Other notable mods: k&n cai, lts,x, magna packs, built t56, built rear with 4.30s



RWHP/RWTQ: 412/457

Need to get a new heater do to mine crapping out. Was on a cool bottle when dynoed!
__________________
2003 Azure Blue M1...SLOW!
boss_pc2 is offline   Reply With Quote
Old 06-28-2013, 07:40 PM   #68
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
Re: Official Nitrous HP/TQ/mods thread

Quote:
Originally Posted by stangpainter View Post
Ok mach guru's,. Need your advice. My 03 mach has 70k on the clock,and has lived a pretty babied life,..i do run it occasionally, and my best time is a 12.80 in 1/4. The engine is stock except for cai, off road x, magnaflo exhaust, 4.10's,sct tune and 315/35 drag radials. So heres the question: I'd like to put 100 shot on this car, as it seems to be the best bang for my budget, in your opinion would you do-it,..? If yes which way would you go,wet or dry,..this would be done strictly for the friday nite track trips,.and it only gets ran a couple time a month. I know hindsite is 20/20,..so please give some insight on your hindsight..thanks
I hope someone answers this since you have almost an identical car as me, only difference is I have 129,000 miles, and 275 40R 17 Drag radials, standing by M1R
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 12-18-2014, 01:49 PM   #69
Explosive
Registered User
 
Explosive's Avatar
 
Join Date: Jul 2010
Location: Michigan
Posts: 876
Re: Official Nitrous HP/TQ/mods thread

Quote:
Originally Posted by stangpainter View Post
Ok mach guru's,. Need your advice. My 03 mach has 70k on the clock,and has lived a pretty babied life,..i do run it occasionally, and my best time is a 12.80 in 1/4. The engine is stock except for cai, off road x, magnaflo exhaust, 4.10's,sct tune and 315/35 drag radials. So heres the question: I'd like to put 100 shot on this car, as it seems to be the best bang for my budget, in your opinion would you do-it,..? If yes which way would you go,wet or dry,..this would be done strictly for the friday nite track trips,.and it only gets ran a couple time a month. I know hindsite is 20/20,..so please give some insight on your hindsight..thanks

This is an oldie but I saw the quote by not a gt.

20/20 would I do it again ? No. It's still not set but overall its been a number of headaches. Partially my fault and some not. I was told what would be the best location for my nozzle. Which ended up being the worst and caused a ton of puddling in my intake boot. My car now has 40k on it and the stock fuel pump was appearing as it couldn't keep up with a 50 shot let alone a 100. But this may have had to do with the fact all my fuel was trapped in my intake and the nitrous was probably getting to the cylinders so I think I was basically smacking it with a dry shot but no extra fuel. Long story short upgraded fuel pump, went back on dyno and discovered the puddle issue. Now have a plate and will be going back in spring to get it all worked out. Wont say that I regret it yet. But, had I the patience I would have held out and kept putting that spare cash aside for a turbo setup.

I'm not at all saying don't go n20, I'm not upset that I went this route. I'd like to go turbo later and if I do I'll keep the nitrous on the car too. I just wonder often had I not been given that poor advice on nozzle location, would my first dyno trip gone smooth ? Between the kit, the what I feel are needed extras window switch/little fittings and nice steel braided lines and going from a nozzle to a $300 plate I've got some money sank into this. So in MY situation, looking back no it was a major pita and I could have saved and just went with boost from the start. However MY situation is not all that common. I will say though after having this happen id never put a kit on and not get a dyno tune, ever. After all of this there is a company I will no longer deal with....
Explosive is offline   Reply With Quote
Old 12-18-2014, 08:18 PM   #70
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
Re: Official Nitrous HP/TQ/mods thread

Great "real world "reply Explosive, thanks. I didn't realize how long ago this was, went P1 instead, and learned ANY power adder has its issues and challenges..(you with Nitrous, me with belt shredding and TKAT13 with turbo woes). If you take on each issue and have a plan in advance , it can only make it go smoother, but there WILL be days it will have you thinking, "Man, it was running so good stock, what have I done "!!
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 12-18-2014, 09:51 PM   #71
Explosive
Registered User
 
Explosive's Avatar
 
Join Date: Jul 2010
Location: Michigan
Posts: 876
Re: Official Nitrous HP/TQ/mods thread

It was just irritating that such a big name company with such a reputation could make the mistakes they did. And even with that, I dont run all over the internet bashing them wherever I can. But between the poor technical advice, and terribly designed products that look cool but obviously never got much testing I was fed up. Became obvious their rep is simply from bandwagon people who see the name on the tv and jump aboard

Finally one day called nitrous outlet and first thing I noticed was the guy on the phone knew his **** and could actually give me straight answers. I ended up buying the n20 plate, and that was my first purchase from them. It showed up at my door in bad shape, bunch of slag in the holes, discolored etc, it was a mess. I wasnt a dick about it just snapped some pics and sent them in an email and was like uhhh, whats up with this ? I hadnt left any contact info but they must of found me in their system from the order and actually picked the phone up and called me to apologize about the issue, and that it even got out their door like that and got me a call tag and was able to get me another plate. I explained my issues with the other company and they were like well i hope this doesnt turn you off of our stuff we will definitely make it right. Which as far as I'm concerned the fact they actually said yea we sent you a piece of **** we will make it right was all I want from a company. Ended up i had bought their last plate so it took a few weeks to get the replacement but it was no biggie my car wont hit the dyno again till spring. I was missing the free shirt he promised lol, but I'm not sweating it just glad I got a good piece. I'll be buying from them from now on, stand up guys.
Explosive is offline   Reply With Quote
Old 03-06-2015, 06:31 PM   #72
blk 04 mach 1
Registered User
 
blk 04 mach 1's Avatar
 
Join Date: Dec 2008
Location: Hallsville Texas
Posts: 953
Re: Official Nitrous HP/TQ/mods thread

have you installed the plate? what kind of setup are you running?
blk 04 mach 1 is offline   Reply With Quote
Old 03-06-2015, 07:40 PM   #73
blk 04 mach 1
Registered User
 
blk 04 mach 1's Avatar
 
Join Date: Dec 2008
Location: Hallsville Texas
Posts: 953
Re: Official Nitrous HP/TQ/mods thread

has everyone lost interest in Nitrous?
blk 04 mach 1 is offline   Reply With Quote
Old 03-06-2015, 08:02 PM   #74
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Official Nitrous HP/TQ/mods thread

Quote:
Originally Posted by blk 04 mach 1 View Post
has everyone lost interest in Nitrous?
filling the nitrous bottle became a PITA, having boost on tap, all the time is much better. Nitrous is also no longer cheap to fill, I think my last bottle was 40.00+. After you go through a few bottles the turbo option looks better. At least, this is why I dropped nitrous.
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 03-06-2015, 11:51 PM   #75
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,005
Re: Official Nitrous HP/TQ/mods thread

Quote:
Originally Posted by blk 04 mach 1 View Post
has everyone lost interest in Nitrous?
Are you looking for a setup?
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁
311-420 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:03 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<