|
09-07-2007, 02:56 AM | #1 |
Slow :(
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
|
Rear brakes How to:
Looks like a piece of cake eh? Nah, really, looks like tough stuff to lots of people, but it's VERY easy.
It actually is, and if you follow these instructions, replacing the pads/rotors should take 10-15 minutes for each side. Yes, you can do your rear brakes in 1/2 an hour!! See that handbrake cable? You shall NOT be messing with it or taking up hours trying to put it back with it's Godforsaken spring, plus it is in the way of the bottom 15mm bolt. If you attempt to take it off, it will not come off. Why? Because the cable is in the way. We shall not be going that nutty route, we shall do it the east and fast way. Ready? 1. Jack said car up. 2. Take respective wheel off 3. Take the two 13mm bolts off. They are located next to the accordion boots that house the caliper sliders. In this pic below, I have the 13mm wrench on the bolt, and I'm using a larger deep socket over the smaller wrench for leverage and to prevent discomfort from my palm. 4. Then it's onto the 2nd 13mm bolt..(Steps # 3 and #4 should take 1-2 minutes at the most). *Note* For 99-04 COBRA IRS setup, at this point, you have to first remove the little screw that holds the handbrake cable to the rear control arm. This is located where the rear spring sits in it's perch. There is a little bracket that holds the handbrake cable to the arm...as shown in this photo below: 5. Caliper comes off very easily...just lifts up...and also moves that dreaded handbrake cable out of the way of the two 15mm bolts that you'll be heading for next. (Notice that the pads are still in place?..pretty cool huh?)
__________________
Mods *BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq *MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes* Last edited by 006; 12-08-2009 at 05:11 PM. |
09-07-2007, 02:57 AM | #2 |
Slow :(
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
|
Re: Rear brakes How to:
continued...
6. At this point, you can use a rear caliper screw-in tool ($5-10 at any local auto parts store), or just rent a much better kit such as this or buy one for yourself. www.Harborfreight.com sells the kit for $29-39.00 6. (a) Screw the piston in as shown: Step # 6 takes about 2 minutes of grunting...still very easy!! 7. Now, if you're replacing the rotors, grab a breaker bar, a 15mm socket and a nice large socket wrench, and take those 2 (totally exposed/unobstructed) 15mm bolts off. *Never use a torque wrench for this. Wrench shown was for illustration purpose only* Another angle: (see? no handbrake cable in the way) Yay! Step # 7 is necessary IF you're going to take the rotors off and either replace them with new ones, or going to take them down to your local parts store to have them resurfaced with a lathe. (takes a very fine layer off and makes them nice and flat surfaced). 8. When that process is complete, replace the bracket and resinstall the two 15mm bolts (Use some thread locker/locktite on the bolt's threads first). Then place the new pads as shown with the anti-rattle clips at both ends. 9. Slide caliper back onto the bracket and install the two 13mm bolts back onto the sliders with the accordion boots. (ALSO NOTE: This would be an EXCELLENT time to slide those boots off to expose the shiny sliders inside. Grease them with some high temp grease and they should be good until the next brake pad change. This prevents a very common problem of rear caliper SEIZING which is normally due to exposed sliders that have gone dry and caused the heat from the calipers to seize the little slider piston into the caliper...and prevents use of rear brakes and can be very dangerous.) -Ken EDIT**** If imageshack (pic hosting site) takes a crap and the pics do not show up, my buddy copied my write up and hosted it on his site: http://newyorkmustangs.com/forums/ho...24.html?t=4024 Take care! -Ken
__________________
Mods *BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq *MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes* Last edited by 006; 12-08-2009 at 05:16 PM. |
09-07-2007, 08:15 AM | #3 |
Braderunna
Join Date: May 2004
Location: hampton, va
Posts: 4,949
|
Re: Rear brakes How to:
Another excellent write-up from Agent 006! Thanks for the post!
__________________
"Sparky"- 2003 Azure Blue w/MT and IUP Visit my garage on mach1mustang.org for details. |
09-07-2007, 09:58 AM | #4 |
Lakers beat our butts
Join Date: Jan 2004
Location: San Antonio TX
Posts: 2,889
|
Re: Rear brakes How to:
I always take the bracket/Caliper off as an assy. Makes it alot easier at least for me.
__________________
SPURS ARE NBA 07 CHAMPS!!!,but we wont be in 08 04 Oxford White 5 Spd with IUP K&N Aircharger Borla Stingers SLP Catted X Steeda Tri-Ax SCT flash tune. Drilled/Slotted rotors all 4 corners. 283rwhp (Mustang Dyno) 306rwhp (sae on Dynojet) D/O/B 12-05-03 Del. 01-21-04 |
09-19-2007, 04:44 PM | #5 |
Registered User
Join Date: May 2007
Location: Frankfort, Il
Posts: 36
|
Re: Rear brakes How to:
Great post!!! A lot of help..Thanks
|
09-19-2007, 07:43 PM | #6 |
Original 03 TR Owner
Join Date: Apr 2004
Location: Waco, TX
Posts: 2,860
|
Re: Rear brakes How to:
great pics too!
Big Ron |
09-22-2007, 09:06 PM | #7 |
I miss my friend
Join Date: Jul 2006
Location: Middle Georgia
Posts: 6,020
|
Re: Rear brakes How to:
Isn't it a NO-NO to use a torque wrench to remove nuts or bolts? I've always been advised to not do this.
__________________
“Freedom itself was attacked this morning by a faceless coward and freedom will be defended.” “We will not tire, we will not falter, and we will not fail,” -George W. Bush |
09-23-2007, 10:13 AM | #8 |
Fear The Mullet!
Join Date: Sep 2007
Location: Springfield, MO
Posts: 58
|
Re: Rear brakes How to:
Thanks for this post! I went into my brake job blind thinking it was gonna be like all the rest but after being given the wrong pads and bad advice, that would have made this project into an all day thing. I finally checked the forum and found this that answered everything and I finished about a half hour after looking at this!:ORANGE:
|
10-05-2007, 02:06 PM | #9 |
I Am Cornholio!!!
Join Date: Aug 2003
Location: Republic of Texas
Posts: 3,745
|
Re: Rear brakes How to:
Thanks 006....another great writeup
__________________
Black 03 5spd w/ IUP Born on 02/25/2003 (thanks Donna) Left home and moved onward 12/19/22 |
11-03-2007, 01:27 PM | #10 |
Registered User
Join Date: Sep 2003
Location: Houston, TX
Posts: 149
|
Re: Rear brakes How to:
Just wanted to thank 006...great write up! One point I wanted to make, though: the bolts going into the "accordian boot" covered sleeves are 12mm on my car.
Again, awesome write up. It took me 2 hours to do it, but I've never done rear brakes like this before. Thanks
__________________
2003 DSG Mach 1 The Thread Killer |
11-28-2007, 11:24 PM | #11 |
Registered User
Join Date: Dec 2003
Location: st.louis, mo.
Posts: 114
|
Re: Rear brakes How to:
Excellent write ups on the front and rear brakes. All write ups should be this plainly written and with such clear and precise picltures.
|
11-29-2007, 10:17 AM | #12 |
Charles U. Farley
Join Date: Jun 2006
Posts: 1,112
|
Re: Rear brakes How to:
REALLY appreciate all of the effort that you put into this!
|
09-28-2008, 09:32 AM | #13 |
Registered User
Join Date: Jul 2004
Location: Toronto, Ontario
Posts: 10
|
Re: Rear brakes How to:
One tip I learned the hard way. There is an indexing tab on the brake pad needs to fit into one of the two grooves cut in the piston top that you use to screw it back into the caliper. IF you dont recognise this, then this indexing pin digs a nice hole in the top of your aluminum piston ... dont ask me how I know ....
Wish I had read this post first. Would have saved me a ton of time. Good work |
09-27-2009, 01:56 PM | #14 |
Registered User
Join Date: Dec 2008
Location: Hallsville Texas
Posts: 953
|
Re: Rear brakes How to:
Thanks again for another helpful post!
|
12-02-2009, 08:20 PM | #15 |
Registered User
Join Date: Sep 2003
Location: OH
Posts: 71
|
Re: Rear brakes How to:
What happened to the pics?
|
12-08-2009, 05:17 PM | #16 |
Slow :(
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
|
Re: Rear brakes How to:
Rehosted the pics on imageshack...
(mustangmods which was the previous pic hosting site, took a ****) Done!
__________________
Mods *BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq *MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes* |
12-08-2009, 05:33 PM | #17 |
Registered User
Join Date: Jan 2004
Location: Grants Pass, Oregon
Posts: 1,777
|
Re: Rear brakes How to:
Re read his post..he did not use the torque wrench nor is he advocatibg that you do so...he was very clear it was for illustration only...
__________________
I drive a slow Mustang....but I drive it Slow....HARD! |
12-08-2009, 06:08 PM | #18 |
Registered User
Join Date: Mar 2007
Location: Acworth, Georgia
Posts: 2,564
|
Re: Rear brakes How to:
Thanks for the beautiful Photos. I figured it was easy, now I know for sure. Thanks again.
|
12-08-2009, 08:28 PM | #19 |
Registered User
Join Date: Sep 2003
Location: OH
Posts: 71
|
Re: Rear brakes How to:
Thanks for placing the pics back on the thread... very helpful
|
05-23-2010, 04:25 AM | #20 |
Registered User
Join Date: Mar 2010
Location: cc,tx
Posts: 131
|
Re: Rear brakes How to:
Im Glad this is here.....cause I just recently bought a pair of billet specialties and im having a hard time fitting them over the stock mach1 rear cobra brake set.There 15 x 10.5 wheels with 6.5 bs.The caliper,brake line hose with that attached to the cube shape piece with the screw piece are in the way and can not fitt the wheel and turn it without rubbing over parts of the brake system.what is there I can do to make clearence?Is there another brake set for the rear to make at least a quarter of an inch of clearence to make that wheel fitt without rubbing issues????Your help would be useful....Thanks.
|
05-23-2010, 08:55 AM | #21 | |
Soldier for Christ
Join Date: May 2009
Location: Willis, TX at The Daddy ASh Ranch
Posts: 30,596
|
Re: Rear brakes How to:
Quote:
you need to start postin some more on here man, good to see you on m1r
__________________
2001 lazer red v6 Mustang coupe sold in Aug 2006 2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012 2013 grey 6 speed coupe GT Mustang Sold in Feb 2014 2013 RED Dodge Charger R/T Sold Nov 2014 2002 custom Blue 02 Auto Trans AM Sold June 2015 1998 Cobra Black Sold summer 2016 Current 2009 Ford F350 FX4 March 2017 (work truck) 2003 OW 5.0 Mach 1 Aug 2020 ASh |
|
05-23-2010, 12:23 PM | #22 |
Registered User
Join Date: May 2008
Location: Ft. Lewis, WA
Posts: 478
|
Re: Rear brakes How to:
im glad you put emphasis on NOT taking off the handbrake cable. that god **** spring takes forever to put back on....when i say forever i mean its one of those where if ur life depended on you getting it back on in an hour you would most certainly just pick death after 15 minutes of working on it.
|
09-05-2010, 11:26 PM | #23 |
Registered User
Join Date: Jun 2009
Location: Muncie, Indiana
Posts: 69
|
Re: Rear brakes How to:
I just put new pads and rotors on my mach this evening. We had trouble getting the caliper to slide down over the pads once they were in the bracket. We tapped it down with a hammer and got it together. However, once we put the wheels back down and dropped it down, the back brakes are acting as if they are stuck and won't release. At this point it was too late in the evening to take it back apart. I'll have to mess with it tomorrow(hopefully) and see what we did wrong.
__________________
04 DSG auto w/C&L inlet pipe, Spectre drop-in filter, o/r X Pipe, Diablosport Tune, 18x9 & 18x10 FR500s, 265/35 & 285/35 Sumitomo HTRZ II Pics |
09-06-2010, 03:34 AM | #24 |
Giant Member
Join Date: Jun 2005
Location: Merritt Island, FL
Posts: 1,093
|
Re: Rear brakes How to:
You got GT pads. Take em back and get Cobra/Mach 1 pads - you're about the 100th person this has happened to
(if you're using a hammer to put your brakes together, something is WRONG)
__________________
Tom 2004 Azure Blue, Manual, IUP #5210 4.10's Magnum 500's Eibach Sportlines/ Bilstein MM Panhard Bar Toyo 295 & 265/35/18's MGW Shifter JLT RAI Predator Tune PHP Intake Spacer SLP LM I Catback & Catted X IAC Restrictor CJ Emblems |
09-06-2010, 06:22 PM | #25 |
Registered User
Join Date: Jun 2009
Location: Muncie, Indiana
Posts: 69
|
Re: Rear brakes How to:
Thanks. I figured it out late last night. I had the QC627 Wagner pads, and needed the PD627A. I compared the two and there doesn't seem to be a huge difference. I'm going to put them on now and hopefully won't have any issues.
__________________
04 DSG auto w/C&L inlet pipe, Spectre drop-in filter, o/r X Pipe, Diablosport Tune, 18x9 & 18x10 FR500s, 265/35 & 285/35 Sumitomo HTRZ II Pics |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|