2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Tuning & Dyno Testing/Results

Tuning & Dyno Testing/Results Questions, experiences & results for electronic tuning and dyno tests

Reply
 
Thread Tools Display Modes
Old 10-29-2017, 04:31 PM   #1
Machwon Jerry
Registered User
 
Machwon Jerry's Avatar
 
Join Date: Oct 2017
Location: Jacksonville, Florida
Posts: 25
Intake Spacer Dyno Results

Okay everyone I did a little science experiment to see how intake spacers performed on Mach 1s. I took my Mach 1 to the dyno ran 2 baseline runs then put the spacer on and ran 2 more runs without any tuning to see what the results would be. I was a little surprised at the results. I've attached a a couple of pics of the dyno charts. What do you guys think?
Attached Images
File Type: jpg All runs.jpg (73.0 KB, 97 views)
File Type: jpg Best runs.jpg (68.1 KB, 75 views)
File Type: jpg Air fuel mix.jpg (66.8 KB, 65 views)
__________________
-Eagle 301 stroker kit
-Pocket ported heads
-Comp Cams 106100s
-Roy's 3/8" Intake Spacer
-K&N CAI
-Full MAC exhaust
-Steeda UDPs
-Steeda Tri-ax shifter
-Exedy Stage 2 clutch
-Exedy flywheel
Machwon Jerry is offline   Reply With Quote
Old 10-29-2017, 04:32 PM   #2
Machwon Jerry
Registered User
 
Machwon Jerry's Avatar
 
Join Date: Oct 2017
Location: Jacksonville, Florida
Posts: 25
Re: Intake Spacer Dyno Results

I forgot to mention this testing was done with a 3/8" spacer.
__________________
-Eagle 301 stroker kit
-Pocket ported heads
-Comp Cams 106100s
-Roy's 3/8" Intake Spacer
-K&N CAI
-Full MAC exhaust
-Steeda UDPs
-Steeda Tri-ax shifter
-Exedy Stage 2 clutch
-Exedy flywheel
Machwon Jerry is offline   Reply With Quote
Old 10-30-2017, 09:16 PM   #3
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,005
Re: Intake Spacer Dyno Results

Seems worthwhile to me!

Care to be more specific about your setup?
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁
311-420 is offline   Reply With Quote
Old 11-01-2017, 01:37 PM   #4
sutyak
it's soo-tack
 
sutyak's Avatar
 
Join Date: Nov 2002
Location: Fairmont, WV
Posts: 2,082
Re: Intake Spacer Dyno Results

Were runs 3,4,5,6 done in order? If so, I see no appreciable gain.
__________________
mark
2004 DSG Mach 1. Built motor. Turbo. 667whp
2006 Sonic Blue Focus. Built motor. Turbo. 12.4 @ 115mph (sold)
2003 DSG Mach 1. 12.65 @ 106 (sold)
sutyak is offline   Reply With Quote
Old 11-01-2017, 03:19 PM   #5
DSG2003Mach1
700 HP Mach
 
DSG2003Mach1's Avatar
 
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
Re: Intake Spacer Dyno Results

ya a little explanation on the numbers would be nice. Theres one pull thats ~10hp/tq lower than all the rest. The others are within about 1%, Id have to imagine thats in the window of margin for error on a dyno
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc...

'12 F150 FX2 Supercrew with Ecoboost daily beater
DSG2003Mach1 is offline   Reply With Quote
Old 11-01-2017, 05:13 PM   #6
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,005
Re: Intake Spacer Dyno Results

Going from the first run (which I'm assuming is without the spacer) to the last run (with the spacer), it looks like +8hp and +8tq unless my eyes are playing tricks on me..
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁
311-420 is offline   Reply With Quote
Old 01-29-2018, 09:59 PM   #7
ab_mach1
Lorraine's driver
 
ab_mach1's Avatar
 
Join Date: Apr 2012
Location: Indianapolis, IN
Posts: 2,442
Didn’t he make 1/2” spacers too? Did it fair better or worse?


IG: @ab_mach1
__________________
  • Instagram: @azurblumach1
  • SCT X3 with LaSota Racing tune
  • Borla Stingers w/JBA off road H pipe
  • MGW short shifter w/comfort handle
  • Eibach Sportlines w/Koni STR.T's and Maximum Motorsports CC plates
ab_mach1 is offline   Reply With Quote
Old 01-30-2018, 10:02 AM   #8
Machwon Jerry
Registered User
 
Machwon Jerry's Avatar
 
Join Date: Oct 2017
Location: Jacksonville, Florida
Posts: 25
Re: Intake Spacer Dyno Results

So I did this test to just see what the results of just bolting on a spacer. would be That's why i did 2 pulls before, then put the spacer on and did 2 more. I am sure it would pick up something if it got a re-tune but the test was just to see if you could just bolt it on and pick something up.
__________________
-Eagle 301 stroker kit
-Pocket ported heads
-Comp Cams 106100s
-Roy's 3/8" Intake Spacer
-K&N CAI
-Full MAC exhaust
-Steeda UDPs
-Steeda Tri-ax shifter
-Exedy Stage 2 clutch
-Exedy flywheel
Machwon Jerry is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 05:19 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<