2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Power Adders

Power Adders Superchargers, Turbos, Nitrous, etc...

Reply
 
Thread Tools Display Modes
Old 02-04-2013, 10:16 AM   #676
fastlane
Registered User
 
Join Date: Mar 2011
Location: Fort Worth, TX
Posts: 209
Re: Eaton Swap.....

Quote:
Originally Posted by watman02 View Post
^ I was going to get a stryker pump and will be running a Lmaf as well. what size injectors are you running??? i have some seimens 60# and some #39 as well. what is your duty cycle on your injectors as well as size. what fuel pressure are you running?? I was thinking about using a billiet flow pulley set up and running the stock and 3.4 and 3.1 pulleys on my ported blower. I see you are only at 14* timing why did you stop there and not take it to 15 or 16? just a question were you starting to loose fuel pressure???
sorry about all the questions
I am running 39# injectors and I am getting close to maxxing them out, ~90% duty cycle. The fuel pump duty cycle is skewed because of how I had it plumbed. I have fixed that issue so I need to get a retune to straighten it all out. The other limiting factor I am running into is the LMAF is close to maxxing out.

The tuner kept the timing at 14* to keep the tune safe. The car was pushing 475hp and I didn't want to go over that point. There is a bit more to be had but I would like for the stock short block to stay together for a while longer.
fastlane is offline   Reply With Quote
Old 02-04-2013, 12:39 PM   #677
watman02
Registered User
 
watman02's Avatar
 
Join Date: Aug 2009
Location: Denver, Ia
Posts: 443
Re: Eaton Swap.....

Quote:
Originally Posted by fastlane View Post
I am running 39# injectors and I am getting close to maxxing them out, ~90% duty cycle. The fuel pump duty cycle is skewed because of how I had it plumbed. I have fixed that issue so I need to get a retune to straighten it all out. The other limiting factor I am running into is the LMAF is close to maxxing out.

The tuner kept the timing at 14* to keep the tune safe. The car was pushing 475hp and I didn't want to go over that point. There is a bit more to be had but I would like for the stock short block to stay together for a while longer.

do you wave any pictures if what u did to the sender to eliminate the fuel issue?
__________________
mods:cai, flowmaster 40's, o/r x tune
best et: 13.17@107mph & 8.56@84.5 1/8
new mods: spacer, 98 cobra cams 4.10's
new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76
New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets
TUNED by ME!....with SCT proracer softwear!!
482hp / 481tq
new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4

00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune
times: 1.8 60' 12.8 @111
watman02 is offline   Reply With Quote
Old 02-05-2013, 07:38 AM   #678
fastlane
Registered User
 
Join Date: Mar 2011
Location: Fort Worth, TX
Posts: 209
Re: Eaton Swap.....

Quote:
Originally Posted by watman02 View Post
do you wave any pictures if what u did to the sender to eliminate the fuel issue?
No pics but all I did was remove the plastic cap that went over the fuel pump nipple and ran a hose from there directly to the fuel hat itself. I drilled a few 5/16" holes into the bottom of the basket as well.
fastlane is offline   Reply With Quote
Old 02-07-2013, 06:24 PM   #679
bleedingfordblu
Registered User
 
bleedingfordblu's Avatar
 
Join Date: May 2007
Location: Leesburg, VA
Posts: 1,985
Re: Eaton Swap.....

so when does the oil filter housing/oil cooler go on? and how?
__________________
2003 Azure Blue Mach 1

Stock bottom end/compression
Eaton M112
Stock upper
Stock lower
K&N intake
Built T56
Bassani mid length headers
Bassani catted x pipe
Bassani slash cut tip catback
Stock 03 Cobra IRS
18x9/10 Forgestar F14
Tuned by Chris Macduff at IMA motorsports
429hp 407 tq @ 7.5 lbs of boost
bleedingfordblu is offline   Reply With Quote
Old 02-07-2013, 06:48 PM   #680
bleedingfordblu
Registered User
 
bleedingfordblu's Avatar
 
Join Date: May 2007
Location: Leesburg, VA
Posts: 1,985
Re: Eaton Swap.....

ok who else got rid of the nipple thing under the lower intake manifold? mines being a pain in the a$$ and wont let the manifold sit flush. what do i need to delete all that?
__________________
2003 Azure Blue Mach 1

Stock bottom end/compression
Eaton M112
Stock upper
Stock lower
K&N intake
Built T56
Bassani mid length headers
Bassani catted x pipe
Bassani slash cut tip catback
Stock 03 Cobra IRS
18x9/10 Forgestar F14
Tuned by Chris Macduff at IMA motorsports
429hp 407 tq @ 7.5 lbs of boost
bleedingfordblu is offline   Reply With Quote
Old 02-08-2013, 10:25 AM   #681
fastlane
Registered User
 
Join Date: Mar 2011
Location: Fort Worth, TX
Posts: 209
Re: Eaton Swap.....

I kept the nipple under the lower intake, I just made sure it was screwed in very snuggly.

The oil cooler goes on eaiser if you raise the driver's side of the engine a little and before you install the alternator.
fastlane is offline   Reply With Quote
Old 02-08-2013, 05:49 PM   #682
watman02
Registered User
 
watman02's Avatar
 
Join Date: Aug 2009
Location: Denver, Ia
Posts: 443
Re: Eaton Swap.....

Quote:
Originally Posted by bleedingfordblu View Post
ok who else got rid of the nipple thing under the lower intake manifold? mines being a pain in the a$$ and wont let the manifold sit flush. what do i need to delete all that?
What is this nipple for?
__________________
mods:cai, flowmaster 40's, o/r x tune
best et: 13.17@107mph & 8.56@84.5 1/8
new mods: spacer, 98 cobra cams 4.10's
new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76
New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets
TUNED by ME!....with SCT proracer softwear!!
482hp / 481tq
new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4

00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune
times: 1.8 60' 12.8 @111
watman02 is offline   Reply With Quote
Old 02-08-2013, 06:41 PM   #683
machgsxr
Registered User
 
machgsxr's Avatar
 
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
Re: Eaton Swap.....

Screw down that nipple like an extra three threads. It will get really tight.

Its for the pcv system.

I put the upper alternator bracket on, then the oil cooler and then the alternator then the lower bracket. Never had to lift the motor to get the cooler on, unless maybe you have a mm k member at which point i highly suggest an oil filter relocation kit.
machgsxr is offline   Reply With Quote
Old 02-08-2013, 07:17 PM   #684
JaybTorchedMach
Registered User
 
JaybTorchedMach's Avatar
 
Join Date: Mar 2010
Location: Albuquerque, NM
Posts: 1,746
Re: Eaton Swap.....

I can't wait to start my swap

Great info in here!
JaybTorchedMach is offline   Reply With Quote
Old 02-09-2013, 03:44 PM   #685
bleedingfordblu
Registered User
 
bleedingfordblu's Avatar
 
Join Date: May 2007
Location: Leesburg, VA
Posts: 1,985
Re: Eaton Swap.....

Can anyone post up a pic of the oil cooler?
__________________
2003 Azure Blue Mach 1

Stock bottom end/compression
Eaton M112
Stock upper
Stock lower
K&N intake
Built T56
Bassani mid length headers
Bassani catted x pipe
Bassani slash cut tip catback
Stock 03 Cobra IRS
18x9/10 Forgestar F14
Tuned by Chris Macduff at IMA motorsports
429hp 407 tq @ 7.5 lbs of boost
bleedingfordblu is offline   Reply With Quote
Old 02-09-2013, 05:56 PM   #686
watman02
Registered User
 
watman02's Avatar
 
Join Date: Aug 2009
Location: Denver, Ia
Posts: 443
Re: Eaton Swap.....

Quote:
Originally Posted by bleedingfordblu View Post
Can anyone post up a pic of the oil cooler?
Installed?? or just a on the banch pic?
__________________
mods:cai, flowmaster 40's, o/r x tune
best et: 13.17@107mph & 8.56@84.5 1/8
new mods: spacer, 98 cobra cams 4.10's
new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76
New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets
TUNED by ME!....with SCT proracer softwear!!
482hp / 481tq
new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4

00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune
times: 1.8 60' 12.8 @111
watman02 is offline   Reply With Quote
Old 02-09-2013, 06:03 PM   #687
machgsxr
Registered User
 
machgsxr's Avatar
 
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
Re: Eaton Swap.....

Quote:
Originally Posted by bleedingfordblu View Post
Can anyone post up a pic of the oil cooler?
01 cobra cooler on the left and the 03 on the right. Can you tell the difference?
Attached Thumbnails
01oilcooler.jpg   03oilcooler.jpg  
machgsxr is offline   Reply With Quote
Old 02-10-2013, 08:58 AM   #688
bleedingfordblu
Registered User
 
bleedingfordblu's Avatar
 
Join Date: May 2007
Location: Leesburg, VA
Posts: 1,985
Re: Eaton Swap.....

Yeah i think i got it thanks!
__________________
2003 Azure Blue Mach 1

Stock bottom end/compression
Eaton M112
Stock upper
Stock lower
K&N intake
Built T56
Bassani mid length headers
Bassani catted x pipe
Bassani slash cut tip catback
Stock 03 Cobra IRS
18x9/10 Forgestar F14
Tuned by Chris Macduff at IMA motorsports
429hp 407 tq @ 7.5 lbs of boost
bleedingfordblu is offline   Reply With Quote
Old 02-11-2013, 02:28 PM   #689
watman02
Registered User
 
watman02's Avatar
 
Join Date: Aug 2009
Location: Denver, Ia
Posts: 443
Re: Eaton Swap.....

What do you guys do about cooling? I see over on svtp some guys swear by the 170 t-stat? those of you who have done the swap. have you done anything too your cooling system? adjust the fan temps? anything?
__________________
mods:cai, flowmaster 40's, o/r x tune
best et: 13.17@107mph & 8.56@84.5 1/8
new mods: spacer, 98 cobra cams 4.10's
new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76
New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets
TUNED by ME!....with SCT proracer softwear!!
482hp / 481tq
new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4

00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune
times: 1.8 60' 12.8 @111
watman02 is offline   Reply With Quote
Old 02-11-2013, 07:28 PM   #690
bleedingfordblu
Registered User
 
bleedingfordblu's Avatar
 
Join Date: May 2007
Location: Leesburg, VA
Posts: 1,985
Re: Eaton Swap.....

Quote:
Originally Posted by watman02 View Post
What do you guys do about cooling? I see over on svtp some guys swear by the 170 t-stat? those of you who have done the swap. have you done anything too your cooling system? adjust the fan temps? anything?
i got the 170 thermostat and plan on using some purple ice or something like that. but i havent had it running yet
__________________
2003 Azure Blue Mach 1

Stock bottom end/compression
Eaton M112
Stock upper
Stock lower
K&N intake
Built T56
Bassani mid length headers
Bassani catted x pipe
Bassani slash cut tip catback
Stock 03 Cobra IRS
18x9/10 Forgestar F14
Tuned by Chris Macduff at IMA motorsports
429hp 407 tq @ 7.5 lbs of boost
bleedingfordblu is offline   Reply With Quote
Old 02-23-2013, 09:10 PM   #691
bleedingfordblu
Registered User
 
bleedingfordblu's Avatar
 
Join Date: May 2007
Location: Leesburg, VA
Posts: 1,985
Re: Eaton Swap.....

Has anyone used a gt500 h/e bracket? I got one from the guy i got my kit from and he says its better because with the cobra one you have to cut the bumper and stuff. Should i just get a cobra bracket?
__________________
2003 Azure Blue Mach 1

Stock bottom end/compression
Eaton M112
Stock upper
Stock lower
K&N intake
Built T56
Bassani mid length headers
Bassani catted x pipe
Bassani slash cut tip catback
Stock 03 Cobra IRS
18x9/10 Forgestar F14
Tuned by Chris Macduff at IMA motorsports
429hp 407 tq @ 7.5 lbs of boost
bleedingfordblu is offline   Reply With Quote
Old 02-23-2013, 10:01 PM   #692
SHAKN' 04
Registered User
 
SHAKN' 04's Avatar
 
Join Date: Jan 2008
Location: Kyle, Texas
Posts: 2,285
Re: Eaton Swap.....

You won't have to trim much from the stock bumper. Using the stock cobra brackets
__________________
**SOLD**04' Mach 1
-Comp Cams 106100's (deg 106/110)
-Eatonswap with 3.4 Pulley
-Full Exhaust (mac lts & xpipe, sss terminator c/b)
-Built Rear w/ 3.55 gears

[B]-Tuned by Lethal Performance of San Antonio
-510hp/478tq
SHAKN' 04 is offline   Reply With Quote
Old 02-24-2013, 08:14 PM   #693
bleedingfordblu
Registered User
 
bleedingfordblu's Avatar
 
Join Date: May 2007
Location: Leesburg, VA
Posts: 1,985
Re: Eaton Swap.....

Ok. How does it mount up?
__________________
2003 Azure Blue Mach 1

Stock bottom end/compression
Eaton M112
Stock upper
Stock lower
K&N intake
Built T56
Bassani mid length headers
Bassani catted x pipe
Bassani slash cut tip catback
Stock 03 Cobra IRS
18x9/10 Forgestar F14
Tuned by Chris Macduff at IMA motorsports
429hp 407 tq @ 7.5 lbs of boost
bleedingfordblu is offline   Reply With Quote
Old 03-03-2013, 02:31 PM   #694
bleedingfordblu
Registered User
 
bleedingfordblu's Avatar
 
Join Date: May 2007
Location: Leesburg, VA
Posts: 1,985
Re: Eaton Swap.....

what did you guys do about the hard line that goes to the ac compressor from the ac condesor when installing the i/c line?
__________________
2003 Azure Blue Mach 1

Stock bottom end/compression
Eaton M112
Stock upper
Stock lower
K&N intake
Built T56
Bassani mid length headers
Bassani catted x pipe
Bassani slash cut tip catback
Stock 03 Cobra IRS
18x9/10 Forgestar F14
Tuned by Chris Macduff at IMA motorsports
429hp 407 tq @ 7.5 lbs of boost
bleedingfordblu is offline   Reply With Quote
Old 03-31-2013, 07:04 PM   #695
watman02
Registered User
 
watman02's Avatar
 
Join Date: Aug 2009
Location: Denver, Ia
Posts: 443
Re: Eaton Swap.....

anybody got pictures of there heat exchanger mounted to the car?
__________________
mods:cai, flowmaster 40's, o/r x tune
best et: 13.17@107mph & 8.56@84.5 1/8
new mods: spacer, 98 cobra cams 4.10's
new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76
New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets
TUNED by ME!....with SCT proracer softwear!!
482hp / 481tq
new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4

00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune
times: 1.8 60' 12.8 @111
watman02 is offline   Reply With Quote
Old 05-01-2013, 03:52 PM   #696
agentorangeCH
Registered User
 
Join Date: Jul 2012
Location: Sursee (CH)
Posts: 27
Re: Eaton Swap.....

Hi Guys


I have to change my inner belt, cause it's squeaking. But my problem is, that I dont know, which belt length I have to buy. I know that the original belt of the 03 Cobra is 96" long, but I have a meziere pump installed, so the belt should be a little shorter.

When I installed the eaton on my 01 cobra, I just reused the belt of the 01 cobra, but I think it's too short.

Anyone an idea?

thanks
agentorangeCH is offline   Reply With Quote
Old 05-02-2013, 05:13 AM   #697
machgsxr
Registered User
 
machgsxr's Avatar
 
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
Re: Eaton Swap.....

From what I remember, I used a stock belt from an 03 cobra on my swap with the ewp. Only issue I had was the water pump rubbing on my pulley bridge.
machgsxr is offline   Reply With Quote
Old 07-08-2013, 07:03 PM   #698
03Machra
Registered User
 
Join Date: Apr 2013
Location: Florida
Posts: 4
Re: Eaton Swap.....

I have a 03/04 Cobra Starter/alternator wiring harness, will using this work with the Mach 1 engine wiring harness? My plans were to use the cobra one so I didn't have to mess with extending the Mach 1s alternator wires.
03Machra is offline   Reply With Quote
Old 07-08-2013, 09:44 PM   #699
watman02
Registered User
 
watman02's Avatar
 
Join Date: Aug 2009
Location: Denver, Ia
Posts: 443
Re: Eaton Swap.....

extending the harness is easy i would recommend doing that. read the whole thread,i know its long but its worth it.
__________________
mods:cai, flowmaster 40's, o/r x tune
best et: 13.17@107mph & 8.56@84.5 1/8
new mods: spacer, 98 cobra cams 4.10's
new times: 2.12 60' 1/8-8.44@85.97 1/4-13.0@109.76
New mods:Ported eaton swap divisonX 340 pump, 3.4 pulley@ 9#, 60# dekas, Lmaf, egr delete, aem wideband, ET streets
TUNED by ME!....with SCT proracer softwear!!
482hp / 481tq
new times:1.7-60' 1/8-7.724 @92.4 and 11.8 @118 1/4

00 SS Camaro M6 with 8.8 rear 3.73 gear. bolt on's and tune
times: 1.8 60' 12.8 @111
watman02 is offline   Reply With Quote
Old 07-31-2013, 08:34 PM   #700
bleedingfordblu
Registered User
 
bleedingfordblu's Avatar
 
Join Date: May 2007
Location: Leesburg, VA
Posts: 1,985
Re: Eaton Swap.....

Well i noticed my cruise control doesnt work. The light on the dash doesnt come on when i turn it on and it doesnt hold speed. I didnt replace the cables when I did my swap. anyone else have this issue?
__________________
2003 Azure Blue Mach 1

Stock bottom end/compression
Eaton M112
Stock upper
Stock lower
K&N intake
Built T56
Bassani mid length headers
Bassani catted x pipe
Bassani slash cut tip catback
Stock 03 Cobra IRS
18x9/10 Forgestar F14
Tuned by Chris Macduff at IMA motorsports
429hp 407 tq @ 7.5 lbs of boost
bleedingfordblu is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 3 (0 members and 3 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:09 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<