2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Brakes & Suspension

Reply
 
Thread Tools Display Modes
Old 11-18-2007, 03:48 PM   #1
006
Slow :(
 
006's Avatar
 
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
Front Brakes How to:


Front COBRA, BULLITT, MACH1 brakes


This is a very simple less than one hour job for everything.

Pads:

I recommend the motorcraft ones. They are anywhere from $95-$105 at most Auto supply stores or performance shops. Motorcraft Part # is BR12B or Ford's part # is 2U2Z-2V001-PA




Jack the car up. Place a Jack stand at an appropriate place just incase the jack decides to go on vacation while you’re underneath the car at some point.

These are self explanatory:




Some of the tools needed to do the job...specially if you'll be replacing the rotors. The two 15mm bolts will require a breaker bar, a regular socket wrench and some lock-tite (thread locker) for when you're bolting things up.

__________________
Mods
*BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq
*MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes*

Last edited by 006; 10-28-2009 at 07:14 PM.
006 is offline   Reply With Quote
Old 11-18-2007, 03:49 PM   #2
006
Slow :(
 
006's Avatar
 
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
Re: Front Brakes How to:



1. Take the wheel off…and turn the wheels so that the rear part of the rotor is exposed.


2. Take the C clip (some people call it an E clip) and washer off as shown:


3. Slide the retainer pin off as shown:


4. Slides right off:


5: Raise the caliper from the bracket as shown from the rear:

__________________
Mods
*BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq
*MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes*

Last edited by 006; 10-28-2009 at 07:16 PM.
006 is offline   Reply With Quote
Old 11-18-2007, 03:50 PM   #3
006
Slow :(
 
006's Avatar
 
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
Re: Front Brakes How to:


6: Slides right off:


7: The bracket is exposed. If you’re going to be replacing the rotors, all you have to do is take the two 15mm bolts out. (In this pic, I am using a cheapo old bent torque wrench that I now use as a breaker-bar/leverage wrench because of how long and strong it is.). When the 2 bolts are out. The bracket slides off and you can remove the rotor and replace it with a new one, OR you can have the old one resurfaced with a lathe. Also known as "turning" the rotors. Most auto parts stores charge a simple $6-10 bucks to resurface each rotor. There is a minimum thickness required for each rotor, thus if your rotor is too thin to remove the thin layer, they will not do it. Most rotors can only be resurfaced with a lathe just once in the life of the rotor.


8: When you have the rotors out and replaced, you need to use some thread locker on those two 15mm bolts. Apply as shown:


9: Back to the pads job…Slide the old brake pads off


10: Rotate the old pads, and Flip them upside down so that the flat surface rests against the pistons and the "raised" part of the pad is on the bottom as shown. Helps the tool catch on it to help push the pistons back..

__________________
Mods
*BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq
*MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes*

Last edited by 006; 10-28-2009 at 07:17 PM.
006 is offline   Reply With Quote
Old 11-18-2007, 03:51 PM   #4
006
Slow :(
 
006's Avatar
 
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
Re: Front Brakes How to:



11: Place the caliper push in tool as shown and screw on the tool to push the pistons back in. Some people can sometimes use their palms to push the pistons back in. This tool is available at most Auto parts stores for cheap. Anywhere from $5-10 bucks There are various different ones that are much more efficient and might cost a little more. (NOTE: Front calipers are PUSH IN only!! Rear Calipers are SCREW IN only, thus there are different tools for the F and R).



12: This just shows what I use to hang my calipers. Old Clothes hangar bent to do the job. Cheap and efficient.



13: Assemble the anti-rattle clips on the new pads just as they were on the old ones. I normally transfer the little rubber absorbers from the old pads onto the new clips as well. Every effort to avoid the micro vibration caused by the pads vibrating in their “slot” is best. You know that trailer truck noise that you hear from some car’s brakes sometimes? Those are caused by this micro-vibration.




14: Place the new pads onto the caliper.

__________________
Mods
*BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq
*MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes*

Last edited by 006; 10-28-2009 at 08:03 PM.
006 is offline   Reply With Quote
Old 11-18-2007, 03:52 PM   #5
006
Slow :(
 
006's Avatar
 
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
Re: Front Brakes How to:


Then Slide the caliper onto the rotor front in forward first as shown. The pad’s front protrusion part slips into the bracket’s U shaped groove at the front and stays locked in.


15: Push down on the rear part of the caliper, then slide the pin as shown. You can “tap” it gently until it’s all the way in.


16: Next slide the washer into the end of the pin, and lock the C clip into place. You might have to “tap” on it as well to make it lock into the groove on the pin.


17: Screw the cap back onto the brake fluid reservoir. (Oh yeah, and if your engine is this dUrty, clean the **** thing..next mod)


18: Put the wheel back on, tighten your lugs, take the jack-stand and jack out and go for a spin.

(VERY IMPORTANT NOTE: Bedding your pads is very necessary as well as seasoning your new rotors. Do not heat up your pads too soon or unnecessarily or you will GLAZE them. You can also WARP your new rotors if you heat them up too quickly and their metallic composition does not get to set itself. BE gentle for the first few times you drive your car. You can research this for how it’s done with a simple Google search)
__________________
Mods
*BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq
*MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes*

Last edited by 006; 10-28-2009 at 08:03 PM.
006 is offline   Reply With Quote
Old 11-18-2007, 04:00 PM   #6
006
Slow :(
 
006's Avatar
 
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
Re: Front Brakes How to:

The ones that come stock are the ones you see that I took off. They have a slightly higher metallic content in them than the Motorcraft ones. The higher metallic content means that the metal contained in the pad composition is higher which results in a noisy "squeal" when coming to a stop. This is normally due to the metal particles in the pad being of a thicker grade and are sometimes resistant to wearing away as they should. This means that it takes weeks to grind/wear down and causes grooves in your rotor and that dreadful noise at the same time.

My GF absolutely HATED that noise on her Terminator. She was used to the quietness from her X5 that she sometimes drives and she nagged me to get that done..which as you can see from the pics, I took care of yesterday. The best replacement pad are the motorcraft which have a slight less metallic composition and is easier on the rotors as well...BUT also offers the exact same stoppage that the stock PBR (australian made) ones that came with the car. Ford charges $207.15 for those retail. (discounted is normally about $150-160). The motorcraft are $95-105 on average.
__________________
Mods
*BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq
*MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes*

Last edited by 006; 10-28-2009 at 08:02 PM.
006 is offline   Reply With Quote
Old 11-18-2007, 05:18 PM   #7
Olivas
Registered User
 
Olivas's Avatar
 
Join Date: Sep 2005
Location: Phoenix, AZ
Posts: 698
Re: Front Brakes How to:

Very nice write up. :ORANGE: :ORANGE:
__________________
2015 CO GT w/ pp
Olivas is offline   Reply With Quote
Old 11-18-2007, 07:11 PM   #8
hawk
Braderunna
 
hawk's Avatar
 
Join Date: May 2004
Location: hampton, va
Posts: 4,949
Re: Front Brakes How to:

Quote:
Originally Posted by Olivas View Post
Very nice write up. :ORANGE: :ORANGE:
I agree. Another Sticky for 006...
__________________
"Sparky"- 2003 Azure Blue w/MT and IUP

Visit my garage on mach1mustang.org for details.
hawk is offline   Reply With Quote
Old 11-25-2007, 09:49 PM   #9
rich1
AUTOMACHTIC
 
rich1's Avatar
 
Join Date: Oct 2007
Location: RTP/ N.C.
Posts: 4,813
Re: Front Brakes How to:

Good write up.I would add that any time the pads are replaced the rotors should be sanded or turned.l
rich1 is offline   Reply With Quote
Old 11-25-2007, 10:44 PM   #10
03blachmach
Guest
 
Join Date: Sep 2007
Location: Savannah, GA
Posts: 59
Re: Front Brakes How to:

i know this is probably a stupid question but i noticed where you said screw the cap back on the brake fluid res. when finished, are you sposed to take the cap off before you start;for air bubbles or something?
03blachmach is offline   Reply With Quote
Old 11-26-2007, 01:59 AM   #11
sbrooks
Registered User
 
sbrooks's Avatar
 
Join Date: Dec 2005
Location: El Paso, TX
Posts: 314
Re: Front Brakes How to:

excellent write up
__________________
2004 Black Mach 1 IUP ,Build Date 21 April 04,, 5 Speed, MGW Shifter, SCT XCAL Tune ,Flowmasters, Mac catted H-Pipe, 4:10 Gears

98 Black Cobra, Build# 3154/5174, Flowmasters, MGW shifter, JLT RAI

[SIGPIC][/SIGPIC]



http://sbrooks.gotstang.com

http://www.svtregistry.com/cobra/199...154/index.html
sbrooks is offline   Reply With Quote
Old 02-21-2008, 06:10 PM   #12
SFMach1
Socom Shooter
 
SFMach1's Avatar
 
Join Date: May 2004
Location: CA
Posts: 418
Re: Front Brakes How to:

Good "how-to" did you bleed the brake fluid by yourself? what did you use?
__________________
'04 DSG Mach 1, 5-speed
my mach 1 web page
SFMach1 is offline   Reply With Quote
Old 03-06-2008, 10:50 AM   #13
006
Slow :(
 
006's Avatar
 
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
Re: Front Brakes How to:

Quote:
Originally Posted by SFMach1 View Post
Good "how-to" did you bleed the brake fluid by yourself? what did you use?
If just doing a simple brake job such as this one, no need to change the brake fluid.

However, I do recommend changing/flushing it once every 2 years if you can. (I do not have a write up for it right now, perhaps when I do my flush in a few weeks I'll make some instructions as well)

Quote:
Originally Posted by 03blachmach
i know this is probably a stupid question but i noticed where you said screw the cap back on the brake fluid res. when finished, are you sposed to take the cap off before you start;for air bubbles or something?
Yes indeed, when starting the job, unscrew the reservoir cap and lay it on the side..make sure no dust/debris falls inside. Reason for this is when you push the pistons on the calipers back in, there can be resistance by the brake fluid inside the lines if you do not open up a vacuum on the other end...and it's a good idea to open up the reservoir in order not to damage any caliper rubber seals. (if you have a straw and cap off one end with your hand, you cannot get your coke out the other side without taking your finger off the other end of the straw)

Cheers!
__________________
Mods
*BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq
*MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes*
006 is offline   Reply With Quote
Old 06-15-2009, 10:12 PM   #14
FEARED
USN
 
FEARED's Avatar
 
Join Date: Aug 2006
Location: NAS Lemoore, CA
Posts: 666
Re: Front Brakes How to:

Thank you for the write up, about to do front brakes!
__________________
2003 Mach 1, Torch Red, 5 Speed, IUP
K&N Intake, MM CC Plates, Lowering Springs, MAC o/r H pipe, SLP Loudmouth Cat Back, Hurst Shifter, Nitrous, Roush LCA, Cobra R Style 17x10.5, SCT Tuner, MT DRs, MM Front Coil Overs, Alum DS ...
Mine Since April 06'
#8616
FEARED is offline   Reply With Quote
Old 08-26-2009, 11:39 PM   #15
mellamoray
Registered User
 
mellamoray's Avatar
 
Join Date: Apr 2007
Location: West New York, NJ
Posts: 238
Re: Front Brakes How to:

I wish I saw this write up before I attempted to do my brakes in the freezing cold last winter. GREAT WRITE UP! time to hook up my printer to my computer and print this out!
__________________
2003 Zinc Yellow-Magnaflow catted x-pipe, Magnaflow "magnapack" catback, Eibach Springs, 18" chrome saleen "S" style rims, cross drilled/slotted rotors, SS brake lines, Vortech Supercharger, 470 HP
2010 Ford Escape V6 XLT 4WD
mellamoray is offline   Reply With Quote
Old 09-27-2009, 01:53 PM   #16
blk 04 mach 1
Registered User
 
blk 04 mach 1's Avatar
 
Join Date: Dec 2008
Location: Hallsville Texas
Posts: 953
Re: Front Brakes How to:

This is a great and helpful post. I am glad I am doing my research before I get into doing this job.
blk 04 mach 1 is offline   Reply With Quote
Old 10-17-2009, 02:11 PM   #17
gamatt
Mustang Fanatic
 
Join Date: Jun 2009
Location: Dacula, GA
Posts: 963
Re: Front Brakes How to:

Is it just me or are the pics not working?
gamatt is offline   Reply With Quote
Old 10-17-2009, 06:44 PM   #18
SGSCOMPS
Registered User
 
SGSCOMPS's Avatar
 
Join Date: Jul 2004
Location: Cincinnati, Ohio
Posts: 106
Re: Front Brakes How to:

Very nice write up, but the pictures are not working for me either
__________________
2004 Mach 1 Torch Red
5 Speed, IUP
Mods:
Roy's 3/8" Aluminum Intake Spacer
K&N Gen II Cold Air Intake
MGW "Orange" Shifter
Flowmaster 40 Series
Previous Mustangs:
1983 GT Bright Red
1969 Mach 1 Candyapple Red
SGSCOMPS is offline   Reply With Quote
Old 10-21-2009, 10:30 PM   #19
006
Slow :(
 
006's Avatar
 
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
Re: Front Brakes How to:

**** mustangmods.com, the owner fugged up the hosting site and now no one can view the write ups I've made on messageboards all over the place.

I'll rehost the pics on a different site.
__________________
Mods
*BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq
*MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes*
006 is offline   Reply With Quote
Old 10-22-2009, 10:50 PM   #20
mach1metalhead
Registered User
 
Join Date: Oct 2007
Location: Orlando, FL
Posts: 1,065
Re: Front Brakes How to:

speaking of the "trailer truck" noise, if some jackass at A DEALERSHIP left out the anti-rattle clips, is there a way to get new ones? i've been driving with that **** sound and i'm about ready to kill someone...
__________________
03 Mach (Auto)
JLT RAI - 1/2" Intake Spacer - Mac longtubes - Mac Prochamber - Borla cat-back - PA Racing k-member - Energy Suspension motor mounts - Eibach Sportline springs - Eibach anti-roll kit - SPC caster/camber kit - Steeda X2 ball-joints - Steeda strut tower bar - Eibach 1" wheel spacers (rear only)
mach1metalhead is offline   Reply With Quote
Old 10-23-2009, 01:51 AM   #21
006
Slow :(
 
006's Avatar
 
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
Re: Front Brakes How to:

Quote:
Originally Posted by mach1metalhead View Post
speaking of the "trailer truck" noise, if some jackass at A DEALERSHIP left out the anti-rattle clips, is there a way to get new ones? i've been driving with that **** sound and i'm about ready to kill someone...
Yeah, $5.99 at Autozone:

http://www.autozone.com/autozone/cat...&parentId=44-0

__________________
Mods
*BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq
*MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes*
006 is offline   Reply With Quote
Old 07-02-2010, 07:51 PM   #22
Cooldbz12
Registered User
 
Cooldbz12's Avatar
 
Join Date: May 2007
Location: FS, TX
Posts: 796
Re: Front Brakes How to:

Very nice wright up! i looked at this and decided to do my brakes myself, got them done under 30 min!.
__________________
2003 Mustang Mach 1
(Bought 11/16/2005)
Eaton Swapped @7psi
(On 10/24/15)
13.2@107 (Bone Stock Run)

2000 3.8 Mustang
Sold But Will Never Be Forgotten
Cooldbz12 is offline   Reply With Quote
Old 10-19-2010, 10:07 PM   #23
lifeofaknight
Registered User
 
lifeofaknight's Avatar
 
Join Date: Sep 2010
Location: Lancaster SC
Posts: 6
Question Re: Front Brakes How to:

I replaced the front brakes on my 04 Mach 1 and they still squeak. I have only had the car for a couple months. Is there any tricks to it? Help needed, they are driving me crazy.
lifeofaknight is offline   Reply With Quote
Old 10-20-2010, 02:49 AM   #24
BluBlurr32V
Bro's B4 Ho's
 
BluBlurr32V's Avatar
 
Join Date: Jul 2007
Location: sunny,ca
Posts: 615
Re: Front Brakes How to:

Yo Ken,

How can I tell if the pads are seperated by inboard/outboard or left/right??

I get a slight chatter only when I go in reverse and step on the brakes. No problems going straight. I was told that I might have the pads on backwards, but by looking at the pads they dont have any mark saying anyting besides the lining #.

I got Stop-tech pads and Powerslots in the front.
__________________
2003 Mach 1 IUP
Azure Blue
DOB: 7/28/03

Magnapack Cat-back, Bassani Catted X-pipe, C&L intake, MGW shifter, MM FLSC, MM Alum steering rack bushings, MM S/S brake lines, MM C/C plates, MM Panhard Bar, H&R Race springs, Blistein HD's, Steeda 2pt STB, Moser 31-spline axles, and S197 posi
BluBlurr32V is offline   Reply With Quote
Old 10-24-2010, 08:32 PM   #25
006
Slow :(
 
006's Avatar
 
Join Date: Nov 2006
Location: Los Angeles
Posts: 252
Re: Front Brakes How to:

Quote:
Originally Posted by BluBlurr32V View Post
Yo Ken,

How can I tell if the pads are seperated by inboard/outboard or left/right??

I get a slight chatter only when I go in reverse and step on the brakes. No problems going straight. I was told that I might have the pads on backwards, but by looking at the pads they dont have any mark saying anyting besides the lining #.

I got Stop-tech pads and Powerslots in the front.
I recommend it this way

O/I [motor] I/O

The pads with a low pad sensor/scrape clip riveted into the pad goes on I
The pads without it, go O

This way, if the inside pad wears out prematurely or is slightly lower than the outside pad, then you will be able to tell when you hear the sensor/scrape clip scraping the rotor. This is an indication that the pads need to be replaced.

Note: The outside pad can be visually inspected to see how low it is. The hidden pad on the inside cannot, this is why it's better to place the pad with the scrape clip on the inside.

*(you can have the rotors resurfaced at the same time as well if they have enough left).

The pads cannot be backwards, they only fit one way.

The noise you mention sounds like you might be missing the anti-rattle clip/s or they have shifted out of their spot.
(See the $5.99 solution from Autozone that I posted earlier)


Visuals:

See the 2nd pad from the top, that is the scrape clip that is riveted on the left.



See these two pads? They will go on the inside. The top one will to to the right (passenger) side of the car on the inside.
The lower one will go to the driver's side on the inside.



This new pad in the foreground will go on the outside. See, no scrape clip.
__________________
Mods
*BRAND NEW 2000 4.6L DOHC COBRA MOTOR w/ T45* 294.18 rwhp and 295.96 rwtq
*MAC catback*H&R Springs*Front Bilsteins, w/ Tokico rear illuminas*8.8 w/ 3.55's*MM CC plates*Subframes*Cobra F&R Brakes*

Last edited by 006; 10-24-2010 at 09:02 PM.
006 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:29 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<