|
03-06-2011, 10:40 AM | #176 |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: 4.30's or 4.10
Although I was very tempted to switch to 4.30s when I re-did my rear end, this thread made it pretty clear that the best advantage for 4.10s or 4.30s would be for a track or at low speeds. It was a little more important to me to have a car that was "faster" (top end) not "quicker" (bottom end). I justify horsepower for passing trucks on the freeway, and the unlikely but possible need to outrun someone chasing you, so that's why I prefer 3.55s.
When people ask which gear is "faster" (4.30s or 3.55s), I have a hard time because it really depends on what standard you judge it by- 1/8 mile, 1/4 mile, 75mph+... each set up has pros and cons or there would only be one option. MY personal preference (though I will make it VERY clear I do NOT promote street racing) is to see what a car does all out- not 0-60, 1/8, 1/4, but 0-130 or a mile. If not, you end up with cars like the new skyline GT-R or Subarus, where the technicians gave it gearing and AWD to satisfy the 0-60 & 1/4 mile times (the only thing people read about) but the car gets passed by it's competitors if they race a full mile. http://www.youtube.com/watch?v=OZlGMX8G3B4 Is one car truely faster than another if the other car is coming up fast on you, but you reach the 1/4 mile 1st? A race is a race, so yes, but at the same time no. FOR ME, I would rather have the car do best in the long run. That's why I kept 3.55s. Don't get upset or confused- those other gears work miracles for our cars, it just depends on what you are looking for.
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg Last edited by XSELLR8; 03-07-2011 at 05:00 PM. |
03-06-2011, 07:05 PM | #177 |
Registered User
Join Date: May 2010
Location: Ohio
Posts: 378
|
Re: 4.30's or 4.10
XSELLR8
Ok, I hear you and feel pretty much the same way, heres my real question (ON A CLOSED COURSE) Do you say top end like top of 4th, or top like riding out 5th? With the 3.55 gear, your 4th already goes over 140, and with the 4.10s I know its less. If you had 4.10 or 4.30s, couldnt you use that to your advantage and countinue in 5th?
__________________
Ben - 04 Mach 1 -Mac LT, LP o/r x, Mangaflow cb, K&N CAI, MMR 1/2" spacer, Custom cams, degreed ftw 356/339 12.04 @ 113.9 -Is it bench racing if the car hasnt ran in a year? |
03-06-2011, 07:21 PM | #178 |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: 4.30's or 4.10
What I meant by that was that I would not like to pay the price of running out of gear with 4.30s once 4th ended at 120. As mentioned earlier in this thread, 5th is not just another gear. Once you hit it you don't accelerate the same. I had a great time on the Las Vegas freeway a week ago, 3rd being perfect at freeway speeds - it seemed right on my power band. Maybe 4.30s would still be better, but I've heard you run out and need to be in 4rth by that speed and that's right where the advantage switches to 3.55s
Yeah. I am just going off of what I have read here, so I probably still have a lot to learn If 5th was a different ratio, it might be a different story.
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg Last edited by XSELLR8; 03-07-2011 at 04:56 PM. |
03-06-2011, 07:26 PM | #179 |
Registered User
Join Date: May 2010
Location: Ohio
Posts: 378
|
Re: 4.30's or 4.10
ok, ic. Ive never tried to run the car hard in 5th, but I guess it must be pretty useless.
__________________
Ben - 04 Mach 1 -Mac LT, LP o/r x, Mangaflow cb, K&N CAI, MMR 1/2" spacer, Custom cams, degreed ftw 356/339 12.04 @ 113.9 -Is it bench racing if the car hasnt ran in a year? |
03-06-2011, 07:42 PM | #180 |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: 4.30's or 4.10
So does anyone know if the 5th gear ratio listed here is really hard to push, and that's why 5th kills the car? I figure it's like a bike sprocket, the smaller it is, the harder to push. I need interpretation.
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg |
03-17-2011, 08:28 PM | #181 | ||
Registered User
Join Date: Apr 2010
Location: Winston-Salem, NC
Posts: 494
|
Re: 4.30's or 4.10
Quote:
Quote:
I mean if you're running out of gear at the track that's understandable, but you're talking about running 120 plus which is completely overkill if you're just trying to have a little fun. I have way more fun with my 4.30s on the highway at 70mph, at a stop, on turns, at cruising speeds (40-55mph), and just any type of situation you can imagine. My car pulls way harder even in the higher speeds (70+) than my 3.55s ever did. Oh, and my 5th with 4.30s is like my 4th was with 3.55s.
__________________
2004 DSG Mach 1 MGW STS, JLT RAI, PHP 3/8" Intake spacer, Bassani catted x-pipe, Magnaflow Magnapacks, FRPP (Motive) 4.30s, 31 Spline Cobra Differential, 31 Spline Moser Axles, GMS Girdle, H&R Super Sports, Koni Yellow Adjustable shocks/struts, MM caster/camber plates
|
||
03-17-2011, 08:33 PM | #182 |
Registered User
Join Date: Apr 2010
Location: Winston-Salem, NC
Posts: 494
|
Re: 4.30's or 4.10
I'd just have to see that to believe it. For sure to 120 the 4.30s would be quicker, and even going to 130 from 120-130 in fifth I can't see the 3.55s being able to catch the 4.30 geared car.
__________________
2004 DSG Mach 1 MGW STS, JLT RAI, PHP 3/8" Intake spacer, Bassani catted x-pipe, Magnaflow Magnapacks, FRPP (Motive) 4.30s, 31 Spline Cobra Differential, 31 Spline Moser Axles, GMS Girdle, H&R Super Sports, Koni Yellow Adjustable shocks/struts, MM caster/camber plates
|
03-18-2011, 04:27 PM | #183 |
Registered User
Join Date: Feb 2004
Location: Arlington Heights, IL
Posts: 641
|
Re: 4.30's or 4.10
4.30 + big tire
I'll be putting a 4.56 in my Eaton swapped Mach with a big tire this year and go shooting for low 11's
__________________
Azure 2003 Mach 1 - 5spd First Eaton swap - 446 rwhp |
03-19-2011, 05:42 PM | #184 |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: 4.30's or 4.10
Well 04dsgmach1, let me clear some things up here before you get too upset. 1st off, i dont frequent 120 mph. I understand the risks and am not interested in the consequences. Yes, I said I like having a better top end. As you may recall, I like 3.55s for the way 3rd gear is at freeway speeds. The main point I want to make about "running out if gear" is that (according to others) with 4.30s you have to be in 4th at 75 which puts you at a disadvantage from a 3.55 car in 3rd. That is what I meant as far as running out of gear- 3rd gear.
I didn't like the idea of the car running out of breath during 3rd gear (even though you claim it doesn't). I didn't mean to make it seem like I am always doing 120+, just wanted to say I prefer a better top end, mainly for freeway use. Understand that there is a lot of personal preference involved with gear set ups.- I decided 3.55s were better for me for freeway use- don't go around accusing me of always doing 120+ just because I said that. Just because I buy z rated tires because I like the IDEA of a tire that won't blow out at 120 doesn't mean I am always doing 120. Should I accuse you of always street racing because you have a V8 and like 4.30s? See my point? I see your point that there isn't much of a need for 3.55s because you're never up around 120 anyway- you just need to not jump to your first conclusion of MY reasons for having 3.55s. I like lower freeway rpms mainly for less wear and tear on the engine, accessories, drive train, and a few Better mpgs. Try to understand where people may be coming from.
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg |
03-20-2011, 05:31 PM | #185 | |
Registered User
Join Date: Apr 2010
Location: Winston-Salem, NC
Posts: 494
|
Re: 4.30's or 4.10
Quote:
My fourth at 75 still pulls stronger than my 3rd did at 75 with 3.55s. Just letting you know, the reasoning before that you gave didn't really make much sense, unless you did take it up past 120 often, otherwise I can't see why you wouldn't have chosen 4.30s or 4.10s considering your preferences. Just because I'm in 4th at 75 doesn't put me at a disadvantage to your third.
__________________
2004 DSG Mach 1 MGW STS, JLT RAI, PHP 3/8" Intake spacer, Bassani catted x-pipe, Magnaflow Magnapacks, FRPP (Motive) 4.30s, 31 Spline Cobra Differential, 31 Spline Moser Axles, GMS Girdle, H&R Super Sports, Koni Yellow Adjustable shocks/struts, MM caster/camber plates
|
|
03-20-2011, 05:44 PM | #186 |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: 4.30's or 4.10
So you're saying it's EASIER to push a 4th gear ratio of 1.0:1 than a 3rd gear ratio of 1.32:1 ??? Other people have already said thats not true. That's why some people have gone back to 3.55s. I think it's pretty clear the car won't pull the same - and dont even think about 5th when you're at .62:1 (even though you never go that fast anyway, but soneone else might on the autobahn or a track) Those final drive ratios may change with 4.30s, but what you need to understand is the fact that 4th and 5th are harder to push than 3rd due to their respective ratios.
You do understand that a better low end sacrifices your top end...don't you? Doesn't sound like you have read all 8 pages of this thread...or payed much attention to others who disagree with what you're saying. One last thing. Have you replaced your 150 mph gauges with V6 120 mph gauges, thrown out your z rated tires, and put on your 115 mph governor yet? If not, why do you have 4.30s ? Ok, just joking around with you now, not trying to start a fight
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg Last edited by XSELLR8; 03-20-2011 at 06:44 PM. |
03-20-2011, 09:19 PM | #187 | |
Registered User
Join Date: Jun 2009
Location: Toronto, Ontario
Posts: 232
|
Re: 4.30's or 4.10
Quote:
Ok im just going to state that i havent read the whole theard....but just one question/comment. Wont the actual top speed of a 4.30 gear car be higher than a 3.55. I know i cant push fifth at all with the 3.55 |
|
03-20-2011, 10:36 PM | #188 | |
Registered User
Join Date: Apr 2010
Location: Winston-Salem, NC
Posts: 494
|
Re: 4.30's or 4.10
Quote:
**** I really need to see what RPMs I'm at at 70-75 I can't remember but I'm pretty sure I'm still able to hit third. I believe I'm a bit over 5k at 70mph in third or maybe I just pulled those numbers out of my ***. Either way, I know what the car felt like very well before I put 4.30s in. I wasn't trying to come off douchey, but your first reasoning for staying with 3.55s didn't even make sense. Now wanting less RPMs on the highway for less wear and tear and stuff is completely understandable.
__________________
2004 DSG Mach 1 MGW STS, JLT RAI, PHP 3/8" Intake spacer, Bassani catted x-pipe, Magnaflow Magnapacks, FRPP (Motive) 4.30s, 31 Spline Cobra Differential, 31 Spline Moser Axles, GMS Girdle, H&R Super Sports, Koni Yellow Adjustable shocks/struts, MM caster/camber plates
|
|
03-20-2011, 11:28 PM | #189 | |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: 4.30's or 4.10
Quote:
On page 1 of this thread its shows 3.55s top out at 236 mph (5th gear) and 4.30s at 194 mph 5th gear. Both are insane numbers we'll never see. The video below is a 3.55 car. Pay attention to how 4th pulls. By the way, this is NOT me in the video. http://m.youtube.com/index?desktop_u...&v=nkcnrDyk1dI
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg Last edited by XSELLR8; 03-21-2011 at 12:12 AM. |
|
03-20-2011, 11:38 PM | #190 | |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: 4.30's or 4.10
Quote:
Good to see that I made a friend today
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg |
|
06-01-2011, 09:44 PM | #191 |
Registered User
Join Date: May 2010
Location: Long Island, NY
Posts: 553
|
Re: 4.30's or 4.10
my 4 banger camry was at 3k at 80... my DD bmw 330 is at 3k when cruising at 80... my mach with 4.10's is about 2600-2700 i believe when doing 80... so im not sure why so many get worried about revving to high in 5th I mentioned to someone the other day that my mach had 4.10's (they were asking about it) and they were stunned... its like the word 4.10's (430 456) has a bad reputation sometimes.... cruising is a marginal difference... its really irrelevant actually.... where the difference in rpm changes dramatically is when the mach is way up in rpm band.... theres spots where the rpm's could be 1000 higher with 4.10's vs 3.55s... but for some reason ( i myself included years ago with my 2k gt) the main concern is cruising on the highway ha
BTW.... just read a few of the posts above.. some interesting info and a good debate...and the more i look at it XSELLR8 has a good point... if this is the case are 4.10 only really beneficially from the dig? seems like from this info 3.55's actually will beat out 4.10's when roll racing.. is this the case? just curious
__________________
04' TR w/ IUP-Vortech V2 3.48" pulley-aftercooler-Anderson PP-90mm MAF-SVT pump-42lb frpp injectors-frpp 4.10-SOS Pillar-FR Fuel,boost/vac gauges-Raptor shift light-aluminum DS-Steeda tri ax-MM ccplates-MM coilovers-Bilstein hd-MM full length subframes-Borla stinger catback-17x10.5 bullitts-Nitto 555r-04 Cobra mirrors/side skirts-CDC decklid panel-Steeda battery box-billet fuel door-sequential tails-Mach 1 sills-billet antenna-MGW Mach 1 plate covers-MGW brake handle-455 rwhp 389 tq Last edited by Rumplemenz; 06-01-2011 at 10:10 PM. |
06-01-2011, 10:52 PM | #192 |
Registered User
Join Date: Jun 2009
Location: Toronto, Ontario
Posts: 232
|
Re: 4.30's or 4.10
I just had 4.30's put in last week and when im accelerating it just feels much quicker.....even 2-4 pulls onto the highway up to about 80.
|
06-03-2011, 12:25 AM | #193 |
Registered User
Join Date: Feb 2008
Location: Sacramento, Ca
Posts: 1,044
|
Re: 4.30's or 4.10
i will have some vids soon... i have 430s going back to 373s.. and back to back runs with my friends..keep you guys posted
check this out guys (ralph green) http://www.mach1registry.org/forums/...eal+ford+gears
__________________
2003 Mach 1 5spd Black with IUP Engine Mods: cone filter, Crower stage 2 cams, Hooker long tubes, SLP Powerflo exhaust Rear end: Cobra diff, moser axles, 3.73 gears, Ford Racing aluminum driveshaft Suspension: Eibach Pro kit with poly isolators And some other small things... 348.6/331.6 sae Last edited by Mach916; 06-03-2011 at 06:51 AM. |
06-09-2011, 12:34 AM | #194 |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: 4.30's or 4.10
I was enjoying the Mach 1 with some friends the other day, and I just dont understand how anyone can hook 4.30s with street tires! I had a hard enough time hooking up with brand new tires. I would also like to run a 4.30 car from a dig, then 60ish to see the differences. By the way Rumplemenez, thanks for being open minded. Its good to discuss both sides of the spectrum and understand I'm not trying to downtalk other gear sets. IMO, the cars are the same HP, it just depends on where you want to end up at what part of the track.
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg |
06-09-2011, 12:51 AM | #195 | |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: 4.30's or 4.10
Quote:
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg |
|
06-13-2011, 11:03 PM | #196 |
Parking Lot Racer
Join Date: May 2008
Location: Cherry Hill, NJ
Posts: 790
|
Re: 4.30's or 4.10
How is traction with boltons and street tires with either 4.10s or 4.30s? Any traction in 1st?
__________________
2004 Mach 1 Maximum Motorsports Equipped |
06-14-2011, 02:33 AM | #197 |
Registered User
Join Date: Feb 2008
Location: Sacramento, Ca
Posts: 1,044
|
Re: 4.30's or 4.10
traction with 430s on street tires...
__________________
2003 Mach 1 5spd Black with IUP Engine Mods: cone filter, Crower stage 2 cams, Hooker long tubes, SLP Powerflo exhaust Rear end: Cobra diff, moser axles, 3.73 gears, Ford Racing aluminum driveshaft Suspension: Eibach Pro kit with poly isolators And some other small things... 348.6/331.6 sae |
07-02-2011, 04:48 AM | #198 |
Registered User
Join Date: Feb 2008
Location: Sacramento, Ca
Posts: 1,044
|
Re: 4.30's or 4.10
all the info you need guys..... http://www.svtperformance.com/forums...l#post10833273
__________________
2003 Mach 1 5spd Black with IUP Engine Mods: cone filter, Crower stage 2 cams, Hooker long tubes, SLP Powerflo exhaust Rear end: Cobra diff, moser axles, 3.73 gears, Ford Racing aluminum driveshaft Suspension: Eibach Pro kit with poly isolators And some other small things... 348.6/331.6 sae |
07-10-2011, 11:01 AM | #199 |
Registered User
Join Date: Jul 2011
Location: River ridge, la
Posts: 9
|
Re: 4.30's or 4.10
Try americanmuscle.com. usually have good prices and free shipping.
|
07-10-2011, 12:22 PM | #200 |
Make My Day... N/A
Join Date: May 2010
Location: Summerside, PE
Posts: 376
|
Re: 4.30's or 4.10
Quoting myself and the difference a year makes. I spun a bearing with my stock engine and s/c setup and swapped in a 03 Aviator engine Mods below) and the 4:10's aren't cutting it anymore. I am looking forward to getting the 4:56's put in.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|