2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Power Adders

Power Adders Superchargers, Turbos, Nitrous, etc...

Reply
 
Thread Tools Display Modes
Old 01-25-2013, 11:07 PM   #201
nightsun
Registered User
 
nightsun's Avatar
 
Join Date: Aug 2009
Location: San Antonio, TX
Posts: 191
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

stock bottom end: no forged teksid 9.2 Comp

PD unit: Whipple 3.4

Pulley size and boost level: 18psi

Fuel system: tripple 340's, full return, 80lb,

Tuner: SCT Tuner Eric Brooks

Other notable mods: LT's, 4.10's, ported heads, comp cams

RWHP/RWTQ: 731/615
nightsun is offline   Reply With Quote
Old 01-25-2013, 11:13 PM   #202
SHAKN' 04
Registered User
 
SHAKN' 04's Avatar
 
Join Date: Jan 2008
Location: Kyle, Texas
Posts: 2,285
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Quote:
Originally Posted by nightsun View Post
stock bottom end: no forged teksid 9.2 Comp

PD unit: Whipple 3.4

Pulley size and boost level: 18psi

Fuel system: tripple 340's, full return, 80lb,

Tuner: SCT Tuner Eric Brooks

Other notable mods: LT's, 4.10's, ported heads, comp cams

RWHP/RWTQ: 731/615

Sweet!!
__________________
**SOLD**04' Mach 1
-Comp Cams 106100's (deg 106/110)
-Eatonswap with 3.4 Pulley
-Full Exhaust (mac lts & xpipe, sss terminator c/b)
-Built Rear w/ 3.55 gears

[B]-Tuned by Lethal Performance of San Antonio
-510hp/478tq
SHAKN' 04 is offline   Reply With Quote
Old 01-30-2013, 08:43 PM   #203
fastlane
Registered User
 
Join Date: Mar 2011
Location: Fort Worth, TX
Posts: 209
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Updated Numbers:

Stock Bottom End: yes

PD unit: Slightly ported Eaton

Pulley size and boost level: 3.1 upper stock lower 10psi

Fuel system: Cobra dual pump hat with stock pumps, Cobra tank, BAP, 39lb injectors

Tuner: SCT Tuner - Manny @ HPP

Other notable mods: LT's, 3.73's, 96 Cobra intake cams, JLT Gen II Big Air CAI, Dragon single blade TB and elbow - conservative tune(13 degrees timing)

RWHP/RWTQ: 495/450

Last edited by fastlane; 04-15-2014 at 02:52 PM. Reason: updated with new numbers
fastlane is offline   Reply With Quote
Old 02-12-2013, 09:39 PM   #204
JaybTorchedMach
Registered User
 
JaybTorchedMach's Avatar
 
Join Date: Mar 2010
Location: Albuquerque, NM
Posts: 1,746
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Quote:
Originally Posted by SHAKN' 04 View Post
At least yours aren't as bad as mine lol mine ar at 106/110. Still make darn good power though
Hey Shakn' 04, I'm considering cams while I have everything apart for the swap. Would you say the 106100's are still a good cam if you were to do it again? Obviously you would get them degreed for boost, but would you go with a completely different setup if you didn't already have these?
JaybTorchedMach is offline   Reply With Quote
Old 04-29-2013, 01:33 PM   #205
Speedtospare
Registered User
 
Join Date: Sep 2010
Location: Newcastle, Ontario, Canada
Posts: 15
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

stock bottom end: yes

PD unit: Stock Eaton

Pulley size and boost level: 3.4 upper stock lower 9 psi

Fuel system: Aeromotive 340 and 39lb injectors return style

Tuner: Diaego from DCT

Other notable mods: All in a 93 coupe. Car meets emissions anywhere. Full closed system with cats. Twin 60 mm TB, stock manifolds, BBK x-pipe, flowmaster.

RWHP/RWTQ: 459.47 WHP and 429.97 TQ

Last edited by Speedtospare; 05-11-2013 at 02:46 PM.
Speedtospare is offline   Reply With Quote
Old 06-15-2013, 08:47 AM   #206
JaybTorchedMach
Registered User
 
JaybTorchedMach's Avatar
 
Join Date: Mar 2010
Location: Albuquerque, NM
Posts: 1,746
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

I just realized I can finally contribute to the thread!

Stock Bottom End: Yes (for now)

PD Unit: Unported Eaton

Pulley Size and Boost Level: Billetflow at 10psi

Fuel system: E85, Twin Focus Pumps, PPRV Delete, Glenn Tank, Kenne Bell BAP, 55lb Injectors

Tuner: SCT X3 Tuned by Chris @ Dynoedge

Other Notable Mods: Kook's, Magnaflow, JLT, Accufab, 4.10's, T56

RWHP/RWTQ: 501/457
JaybTorchedMach is offline   Reply With Quote
Old 08-16-2013, 08:38 AM   #207
GhostRiderblk
Mammoth mach
 
GhostRiderblk's Avatar
 
Join Date: Aug 2009
Location: Florida
Posts: 715
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Stock bottom end: NO

PD unit: 2.8LC KB MAMMOTH

Pulley size and boost level: 3.5 Pulley with 8lb lower 29-30psi to busy holding on to look

Fuel system: dual 340lph stryker pumps, custom hat, return style, 8an feed,stock line return, stock fuel rails, aeromotive regulator

Tuner: 22* timing, sniper tuning, c16

Other notable mods: ported heads, ported lower intake, headers

RWHP/RWTQ: 830RWHP/773RWTQ / mustang dyno
__________________
2.8 Kb Mammoth LC
Manley pistons teflon coated
Manley Rods
Arp hw
nx N20 kit
GhostRiderblk is offline   Reply With Quote
Old 08-22-2014, 09:24 AM   #208
mstangtony
Registered User
 
mstangtony's Avatar
 
Join Date: Apr 2014
Location: Virginia Beach, VA
Posts: 49
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Im loving the Numbers on some of these, but Im looking to install a KB on stock motor. Ideas and cost? anyone? im looking at 450/400 just a rough gustimate on power. not trying to blow my motor up, and i will build in the future.
__________________
[FONT="Comic Sans MS"]2002 STEEDA Mustang - RIP
2004 Competition Orange MACH1 - Purchased 4-24-14 - Arrival (5-2-14)
mstangtony is offline   Reply With Quote
Old 08-22-2014, 09:36 AM   #209
vertigyn
Azure Blue Mach
 
Join Date: Apr 2007
Location: St. Petersburg, FL
Posts: 1,464
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Quote:
Originally Posted by mstangtony View Post
Im loving the Numbers on some of these, but Im looking to install a KB on stock motor. Ideas and cost? anyone? im looking at 450/400 just a rough gustimate on power. not trying to blow my motor up, and i will build in the future.
Depends where you can find a kit. Since the 03/04 Cobra intercooler isn't made anymore by Ford, KB stopped selling the kit. They will sell you all the pieces but you will have to source your own intercooler.

Back when I got mine new, the total cost was about 7,000 (kit, install, custom tune). That was at 15,000 miles on a the factory motor and now I'm at 45,000. The car is a toy and is driven HARD most of the time (autoX and spirited driving). It made 475/440 or so - my post is in this thread somewhere...

The motor is fine - but it did break the transmission, rear end, and axle.
__________________
'03 Azure Blue Mach 1 Built on 4/14/03 S&R Performance
vertigyn is offline   Reply With Quote
Old 10-29-2015, 11:53 AM   #210
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,005
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

After 8 years, I can now contribute to this one.


Stock bottom end: Yes

PD unit: Stock Eaton

Pulley sizes and Boost: Stock pulleys ~7psi

Fuel system: Aeromotive 340lph stryker pump, pprv delete, 39lb. injectors, Cobra 90mm maf

Tuner: Dyno tuned at TrueStreet Motorsports

Other notables: Longtubes/no cats x pipe, magnaflow cb, aluminum driveshaft, built/3.73 rear, Reische 170°

RWHP/RWTQ: 452/409 STD DYNOJET
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁

Last edited by 311-420; 10-29-2015 at 12:35 PM.
311-420 is offline   Reply With Quote
Old 02-03-2016, 07:55 AM   #211
jchambers
All around good guy
 
jchambers's Avatar
 
Join Date: Feb 2005
Location: Milan, OH
Posts: 170
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

KB swapped 2004 Mach 1 on corn at a little less than 14 psi. 617RWHP & 500RWTQ on my Mustang Dyne 1150SE.
Attached Images
File Type: jpg image1.JPG (132.0 KB, 21 views)
__________________
[SIGPIC][/SIGPIC]
Jeff Chambers
FFW S/W #3
10.031@137.5
1990 Mustang GT (race car)
2001 Mustang GT (street car)
CRT Performance, LLC
jchambers is offline   Reply With Quote
Old 02-03-2016, 09:53 AM   #212
xXAzureMach1Xx
04 Mach 1
 
xXAzureMach1Xx's Avatar
 
Join Date: Mar 2008
Location: Pensacola FL
Posts: 272
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Stock bottom end: Yes

PD unit: Single Turbo

Boost level: 5-6 psi

Fuel system: Stock 03 Cobra Tank/Pumps and 40 BAP

Tuner: SCT

Stock long block, T56 on a 28'' M/T

RWHP/RWTQ: 473RWHP/512RWTQ
__________________
04 Mach 1 / Single Turbo/ T56/ Built 8.8/ Full Team Z Suspension / 17/15 Weld RTS
xXAzureMach1Xx is offline   Reply With Quote
Old 02-03-2016, 01:30 PM   #213
Cooldbz12
Registered User
 
Cooldbz12's Avatar
 
Join Date: May 2007
Location: FS, TX
Posts: 796
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Stock bottom end: Yes

PD unit: Eaton 3.65" pulley

Boost level: 6.5psi

Fuel system: Stock Tank, Cobra Pumps, 39lb injectors, VMP 40amp BAP

Tuner: SCT Xcal2, VMP Tuning, Remote Tuned

Other Mods: Alum driveshaft, 4.10s, K&N Cold Air, Electric waterpump.

RWHP/RWTQ: Unknown ( street tuned )
__________________
2003 Mustang Mach 1
(Bought 11/16/2005)
Eaton Swapped @7psi
(On 10/24/15)
13.2@107 (Bone Stock Run)

2000 3.8 Mustang
Sold But Will Never Be Forgotten
Cooldbz12 is offline   Reply With Quote
Old 02-04-2016, 02:02 AM   #214
ASH302
Soldier for Christ
 
ASH302's Avatar
 
Join Date: May 2009
Location: Willis, TX at The Daddy ASh Ranch
Posts: 30,596
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

I be curious to what your HP/TQ numbers are, would drive me crazy not knowing

ASh
__________________
2001 lazer red v6 Mustang coupe sold in Aug 2006
2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012
2013 grey 6 speed coupe GT Mustang Sold in Feb 2014
2013 RED Dodge Charger R/T Sold Nov 2014
2002 custom Blue 02 Auto Trans AM Sold June 2015
1998 Cobra Black Sold summer 2016

Current
2009 Ford F350 FX4 March 2017 (work truck)
2003 OW 5.0 Mach 1 Aug 2020

ASh
ASH302 is offline   Reply With Quote
Old 02-10-2016, 09:06 PM   #215
32VALVR
Registered Mach Abuser
 
32VALVR's Avatar
 
Join Date: Apr 2006
Location: SoCal
Posts: 1,695
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Anyone having trouble with this years winter gas? Any Kenne Bellers running 9lbs on 91 getting tip in or overdrive ping? That is those running stock compression.
Thanks
__________________
04 O/W 5sp with Kenne Bell 2.1 intercooled kit@ 10lbs.
32VALVR is offline   Reply With Quote
Old 02-11-2016, 09:41 AM   #216
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,005
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Quote:
Originally Posted by 32VALVR View Post
Anyone having trouble with this years winter gas? Any Kenne Bellers running 9lbs on 91 getting tip in or overdrive ping? That is those running stock compression.
Thanks
I got bad gas twice at the end of summer in 2014. I remember it happened first in September. First time at an exon and then at a shel. Would ping like crazy but only at WOT. Thankfully I was still n/a at the time. It's why I always turn the music way down before a pull now.
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁
311-420 is offline   Reply With Quote
Old 02-16-2016, 09:44 AM   #217
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Stock bottom end: Yes, 2003 Cobra motor

PD unit: Ported Eaton

Pulley size and boost level: 2.93 upper, 4# lower..15 PSI

Fuel system: 60lb injectors, 90 MM MAF with MAFia, twin improved GT pumps with PPRV delete, KB BAP with wire upgrade

Tuner: Bob Kurgan using SCT X3

Other notable mods: Stage 4 Port, longtubes, O/R X pipe with Magna packs, T56 with 26 spline shaft

RWHP/RWTQ: 524rwhp / 535rwtq

__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 09-21-2016, 10:47 AM   #218
fastlane
Registered User
 
Join Date: Mar 2011
Location: Fort Worth, TX
Posts: 209
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

New number from my recent build:

Stock bottom end: No, forged Mach1 10:1 compression

PD unit: Whipple 3.4 with Crusher inlet

Pulley size and boost level: 3.25" - 25psi

Fuel system: Dual Walbro 455s, full return, ID1000s, Fore Triple hat

Tuner: SCT Tuner Manny Alvarez@HPP Motorsports

Other notable mods: LT's, 4.10's, 96 Cobra intake cams, built 4r75W, e85

RWHP/RWTQ: 730/630

The fuel pumps couldn't keep up so I am installing a 3rd 455 pump and going back to finish the tune. Max timing was 15 degrees and temperature was 100+ with 30% humidity. Updated numbers will be posted soon.
Attached Thumbnails
20160920_153728[1].jpg  
fastlane is offline   Reply With Quote
Old 11-01-2017, 02:56 PM   #219
hendrixinthe70s
the red project
 
hendrixinthe70s's Avatar
 
Join Date: Jan 2008
Location: riverside california
Posts: 136
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

So i just did an eaton sway, Looking at adding a full throttle body, jlt CAI and im wondering if i should use long tube headers or shortys? Pros vs cons to each? any suggestions?
__________________
PROJECT MUSCLE

03 mach1
full bassani exauhst
jlt rai
sportline lowering kit
hendrixinthe70s is offline   Reply With Quote
Old 07-02-2018, 07:17 AM   #220
MachRyan
Registered User
 
Join Date: Nov 2017
Location: IL
Posts: 21
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Eaton swap is done. I can finally add to this thread...


Stock bottom end: Yes

PD unit: Ported Eaton M112

Pulley size and boost level: stock - 7psi

Fuel system: stock + BAP

Tuner: STL Mustangs

Other notable mods: Bassani X-pipe, Borla Exhaust, JLT RAI, 4.10's

RWHP/RWTQ: 411/377

Overall opinion: numbers are disappointing to me - no question. Especially when I compare them to what most others with a very similar setup have achieved. That being said, the car is a blast to drive and because of my low mileage and wanting to keep my car reliable for the long term I'm content...........for now.
MachRyan is offline   Reply With Quote
Old 07-13-2018, 10:46 PM   #221
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Update on mine, 2.3L Whipple, 3.37 upper, 4#lower, ID1000 injectors, 19 psi boost...601rwhp/558 rwTq on Kurgan dyno.
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 07-28-2018, 09:25 AM   #222
fastlane
Registered User
 
Join Date: Mar 2011
Location: Fort Worth, TX
Posts: 209
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Went back to the dyno yesterday to dial in the tune a bit more...

Stock bottom end: No, forged Mach1 10:1 compression

PD unit: Whipple 3.4 with Crusher inlet

Pulley size and boost level: 2.75" - 29psi

Fuel system: Triple Walbro 455s, full return, ID1000s, Fore Triple hat

Tuner: SCT Tuner Manny Alvarez@HPP Motorsports

Other notable mods: LT's, 3.27's, 96 Cobra intake cams, built 4r75W, e85

RWHP/RWTQ: 742/774

Other notable was the blower belt was slipping badly above 6000 rpm. Need a better belt and a little more tension. That should put it over 800 easily.
fastlane is offline   Reply With Quote
Old 07-31-2018, 12:22 PM   #223
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,825
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Quote:
Originally Posted by fastlane View Post
Went back to the dyno yesterday to dial in the tune a bit more...

Stock bottom end: No, forged Mach1 10:1 compression

PD unit: Whipple 3.4 with Crusher inlet

Pulley size and boost level: 2.75" - 29psi

Fuel system: Triple Walbro 455s, full return, ID1000s, Fore Triple hat

Tuner: SCT Tuner Manny Alvarez@HPP Motorsports

Other notable mods: LT's, 3.27's, 96 Cobra intake cams, built 4r75W, e85

RWHP/RWTQ: 742/774

Other notable was the blower belt was slipping badly above 6000 rpm. Need a better belt and a little more tension. That should put it over 800 easily.
You using the green belt? Also I have the plate that goes over the tensioner, would that help ??
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 07-31-2018, 05:52 PM   #224
fastlane
Registered User
 
Join Date: Mar 2011
Location: Fort Worth, TX
Posts: 209
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

No, I was using a standard Gates 8 rib belt that I was able to source quickly. I am going to the Gates RPM belt and a bigger idler to get a little more wrap on the supercharger pulley. Hopefully that fixes the slipping issue. I had the upper pulley carbonited but that didn't help as much as I hoped it would.
fastlane is offline   Reply With Quote
Old 08-20-2018, 10:41 PM   #225
hotford
Registered User
 
hotford's Avatar
 
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:

Quote:
Originally Posted by fastlane View Post
No, I was using a standard Gates 8 rib belt that I was able to source quickly. I am going to the Gates RPM belt and a bigger idler to get a little more wrap on the supercharger pulley. Hopefully that fixes the slipping issue. I had the upper pulley carbonited but that didn't help as much as I hoped it would.
maybe go to a 6 lb lower with a larger blower pulley to help that belt from slipping, heck any belt you use making 29 psi is gonna have a hard time holding it with a 2.75, bigger pulley on the blower would help.
BTW whats your IAT at with that base compression and that boost level.
__________________
1982 GT
2003 Mach 1
2003 Marauder
2011 Shelby GT 500
hotford is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:40 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<