|
|
Photo Gallery | $ Donations $ | Register | FAQ | Social Groups | Calendar | Search | Today's Posts | Mark Forums Read |
General Registry Discussion Topics of Interest (Mach 1 Related or otherwise) for discussions that don't fit other forums. |
|
Thread Tools | Display Modes |
09-04-2019, 04:15 PM | #26 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
Ok
More progress, so you can see that the relay's are different from Cobra to Mach, from the original connector I removed the pins out of the factory two plug and lucky me I had other harness that would match up to the cobra relay harness, pins for the fan plugged in factory like. The fan power wires are the same colour code, now for the circ pump, it has 4 wires, white from the power distribution via the sliver connector, I drilled and added the wire to the other side of the terminal block and routed though the loom to the relay which power supply, Orange with yellow tracer is power to the circ pump, red is 12 volt ignition power which I tapped into the 12 V that supplies the maf, white with red tracer is suppose to go to the PCM pin 83 as the cobra computer monitors it, by way of grounding it no need to hook up as the mach would know as its not programmed for it. I just wired it into the harness on a ground circuit and when ignition is turn on the pump will run, gonna make a toggle switch so when at the track I can jump it in the pits. The IAT is also not used in the Maf location so I used the Cobra Map/IAT2 sensor located in the manifold and made up my own wiring harness using ford connectors and even used the exact colour codes grey/ red and grey wiring, many may ask why, well when adding in a PD blower timing is controlled by IAT and if it see the incoming air which is a lot cooler it can add to much, this way it only see it after the cooler in the manifold which is the one you want. here is it all cleaned up.
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 Last edited by hotford; 09-12-2019 at 12:12 AM. |
09-09-2019, 12:43 AM | #27 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
well little further along...got the inlet all mounted and even relocated the maf in the fender area, coolant tank on.
Only thing I don't like is the IAC hose, gonna try and make that look neater and have it go around the other way and under the TB.. also gonna hook up the stock reservoir bottle for the inner cooler temporarily, car has to go to the Body shop for the front and rear bumpers to be painted, also needs alignment,once that's done I can put it up on the hoist and run the coolant hoses under the car to the rear PNR tank in the trunk. with all the wiring in play I started to mount the panels back on, this is far as I got, family function stopped any further assembly...lol
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 |
09-09-2019, 11:00 AM | #28 |
Can't be bridled
Join Date: Sep 2007
Location: Texas
Posts: 7,006
|
Re: Mach ! Resurrection
Bang-up job. That blower is massive and looks awesome under there.
__________________
2004 Mach 1 #6956 5spd w/IUP Eaton swap, longtubes, built 3.73 SRA 452hp/409tq dynojet🏁 |
09-09-2019, 03:52 PM | #29 | |
Lorraine's driver
Join Date: Apr 2012
Location: Indianapolis, IN
Posts: 2,442
|
Quote:
IKR?! The intake piping looks like 6” DIA. I’m sure it’s not, but it all looks huge in there lol. Sent from my iPhone using Tapatalk Pro
__________________
|
|
09-09-2019, 04:20 PM | #30 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Mach ! Resurrection
that looks awesome!
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
09-12-2019, 01:01 AM | #31 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
Its alive...…
Had to get a start up base file from my buddy Lidio and upload it into the X cal 3 with the Pats turned off for now as I only received one key for the car, plus the PCM isn't the original as I switch the car to Auto, I will get another key and program them to the car later with the IDS. Started up first crank....Who Hoo... ran pretty good for a start up file, this will get me going for now...next steps.. attach the front clip and get it to the alignment shop and then to the body shop for the bumpers to be painted. I tried to upload the video but it wouldn't take......sorry guys one more issue to deal with, when I came into the garage the cluster had dash lines where the OD was and the ABS and Service engine light was on...Hmm after a little investigating found the abs module was back feeding and causing the issue, has a spare ABS module and just quickly plugged her in and verify all was good, I will switch out the unit and bleed the brakes which should only take a couple of hours. I'll update with more pics from the alignment and body shop....
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 Last edited by hotford; 09-12-2019 at 01:45 AM. |
09-12-2019, 08:05 AM | #32 |
Registered User
Join Date: Jul 2004
Location: Raleigh , NC
Posts: 2,093
|
Re: Mach ! Resurrection
Awesome!!
__________________
2004 Torch Red Procharged Mach 1 |
09-12-2019, 09:26 AM | #33 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Mach ! Resurrection
One of the best feelings in the world is hitting the key on a new build and having it fire right up.
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
09-12-2019, 11:26 AM | #34 |
Registered User
Join Date: Jul 2004
Location: Raleigh , NC
Posts: 2,093
|
Re: Mach ! Resurrection
haha!! One of the best feelings after the nerve racking tension before the initial start up!
__________________
2004 Torch Red Procharged Mach 1 |
09-13-2019, 01:01 AM | #35 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
amend to that brother!!
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 |
09-30-2019, 02:11 AM | #36 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
Well little more progress... engine bay wiring and ABS module all done... both fenders are on.... went to adjust the hood striker to align... ran into a slight snag.. the shaker liner rests on the crusher inlet not allowing the hood to close all the way..... options are to remove and just mount the shaker to the underside of the hood as many have done..... Nah I like things the hard way.....lol gonna drop the K-member down as much as 1/2 inch if need be to clear and allow hood closure...also this will help with the shaker mounting too....
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 |
09-30-2019, 09:30 AM | #37 | |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Mach ! Resurrection
Quote:
Is it hard to get the elbow off the blower to get to the spark plugs?
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
|
10-01-2019, 01:30 AM | #38 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
Sewer pipe.....lol it's 5 inch inside diameter, nah it's pretty easy just loosen the hose to the pipe and slide it down and the plastic one to the TB comes off..really like 2 min and you can access the plugs with a extension and flex...looks harder than it is.
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 |
10-06-2019, 11:55 PM | #39 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
Well I installed the lights and slid in the bumper and attached loosely and didn't brother to attach the chip spoiler as the bumpers are coming off for paint anyways....looks so much better with the clip on...lol. ran into a snag...went to get gas and found I only had first gear.. came back with 3 codes...gear selector range out and speed sensor.... well fixed the gear selector one as I had a spare new one and adjusted it... but the speedo is inop...ran out of time to look at it as family life takes over.... should have time in the next couple days..... I will update with my findings and pics when at the Body shop...
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 |
10-07-2019, 01:02 PM | #40 |
Lorraine's driver
Join Date: Apr 2012
Location: Indianapolis, IN
Posts: 2,442
|
Re: Mach ! Resurrection
Looks good. Glad everything fit behind the bumper without modification. Really amazing what the chin spoiler does for the front end too. Hope your prob is just connections or something simple.
__________________
|
10-10-2019, 01:17 AM | #41 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
Well after several hours of diagnosis..... all the wring checks out, even ran a scanner on and determined the speed sensor is actually working but way off, in second gear at 4500 RPM the speedo reads maybe 15 MPH...this all lead back to the tune file.... SCT actually confirmed it...just waiting for a new start up file and go from there...
I think the wife is getting a little jealous and I'm spending more time in the garage....lol
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 |
10-10-2019, 08:40 AM | #42 | |
Heppasketties
Join Date: Aug 2003
Location: Mercer County, NJ
Posts: 4,760
|
Re: Mach ! Resurrection
Quote:
I started a Face Book group for friends and family for a car my sons & I were building for Drag Week this year. It was so the family could see what we were doing, also so we could look back and reference the posts to see our progress.
__________________
M1R Member #1829 2011 Shelby GT-500 Grabber Blue W/SVT Performance Package Born on Friday, 6-25-2010 Purchased 8-19-2010 2003 Zinc Yellow Auto I/UP (Build #8280 of 9652) Born on Thursday, 7/17/03 Purchased 8-18-2003 first owner Sold 8-19-2010 bought GT500 Purchased again 3-3-2017 fifth owner Purchased for my wife to drive (but she knows I love the car) |
|
10-12-2019, 02:02 PM | #43 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
New file up loaded and all is fixed test drove last night and it has all gears What we found was that Ford changed out the reluctor ring in 2004 up all 4r75w trans from 24 to 6 counts ... 2003 down has 24, drove real nice Pic are me leaving in the morning and in the body shop I’ll be there Tuesday to help remove items needing paint,I’ll make sure take lot of pics ... Thanks to who have posted your feed back is much appreciated
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 |
10-19-2019, 07:04 AM | #44 |
Love my Mach
Join Date: Apr 2005
Location: Charlottesville, VA
Posts: 13,678
|
Re: Mach ! Resurrection
Wow. I am saving my money to hopefully do the same exact build. Motor still blown on mine. ☹️
__________________
2003 slowmatic 11.105@117mph w/125 shot of Nitrous best to date Kooks LTsw/OR X, elect cutouts, JLT RAI w/C&L 85 MAH,1" Spacer,PP Lower intake,Accufab TB,160 T-stat,EF Cooling Mod,NX Kit,Mez Electric Water pump,SLP Linelock,FRPP 4.10s-Alum Dif Cover-Alum Driveshaft & SL, Steeda Bumpsteer,MM Alum rack bushings,Deep Alum Tranny pan,Predator,Steeda AUCAs,MM ALCAs, Dspecs,MM CC plates & FLSFCs,MRT Guage cluster,AEM WB,MRT hood struts,Seq TLs, carbon fiber hood/trunk/Cobra wing,220 amp alt |
10-23-2019, 03:23 AM | #45 |
Mach-T
Join Date: Jun 2004
Location: DFW
Posts: 2,865
|
Re: Mach ! Resurrection
Awesome Build!
__________________
Darrell Black '04 Mach 1 Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67 (100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88 New build - 750rwhp; not track tested (yet) Mods: Build Log Paint&Body Tuned by Manny @ HPP |
10-24-2019, 01:54 AM | #46 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
Well my dent doctor buddy Matt got 90 % of the dings out, man I can't say enough about this field of work these guys can do miracles!
toughest one was the one under the gas cap where the body panel meets the bumper cover, he did his best but because of the location, heck I can live with that, I Installed the Black Gas cap and must say I think it looks great! My OCD is driving me nuts so I'm usually at the B/shop every other day...so I had to wash her up and get most of the dust off...lol Here's some shots of the rear bumper in prep... The front clip we are going to align up first them remove the front bumper and R/front fender for paint. more pics when that happens...maybe Fri/ Sat.
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 |
10-24-2019, 02:04 AM | #47 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
Well had some time since the car's at the B/shop...so I took out my Shelby for a date night...…
thought I would share a pic..
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 |
10-24-2019, 01:19 PM | #48 | |
Lorraine's driver
Join Date: Apr 2012
Location: Indianapolis, IN
Posts: 2,442
|
Re: Mach ! Resurrection
Quote:
__________________
|
|
10-31-2019, 01:04 AM | #49 |
Registered User
Join Date: Jan 2005
Location: Durham/Canada
Posts: 236
|
Re: Mach ! Resurrection
Well some more progress...just real busy last bit finding it hard to get over to the B/shop, but the hood shocks are on...must say a lot nicer without that prop rod..lol
The Front fender has had the dent taken out and primed, still needs to be completely sanded but this is as far as I got yesterday, had plans to be there today...but **** happens, tomorrow if I get more time....front bumper should be prepped. more pics to follow...
__________________
1982 GT 2003 Mach 1 2003 Marauder 2011 Shelby GT 500 |
10-31-2019, 04:31 PM | #50 |
Registered User
Join Date: May 2018
Location: Cleveland, OH
Posts: 18
|
Re: Mach ! Resurrection
Love watching this come together for you! Looks fantastic!
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Display Modes | |
|
|