2003-04 Mach 1 Registry Owners Club  

Best Mustang Parts

Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Tuning & Dyno Testing/Results

Tuning & Dyno Testing/Results Questions, experiences & results for electronic tuning and dyno tests

Reply
 
Thread Tools Display Modes
Old 10-29-2017, 05:31 PM   #1
Machwon Jerry
Registered User
 
Machwon Jerry's Avatar
 
Join Date: Oct 2017
Location: Jacksonville, Florida
Posts: 14
Intake Spacer Dyno Results

Okay everyone I did a little science experiment to see how intake spacers performed on Mach 1s. I took my Mach 1 to the dyno ran 2 baseline runs then put the spacer on and ran 2 more runs without any tuning to see what the results would be. I was a little surprised at the results. I've attached a a couple of pics of the dyno charts. What do you guys think?
Attached Thumbnails
All runs.jpg   Best runs.jpg   Air fuel mix.jpg  
__________________
Eagle 301 stroker kit
Pocket ported heads
Comp Cams 106100s
Roy's 3/8" Intake Spacer
K&N CAI
MAC LTs & O/R Prochamber
Steeda UDPs
Steeda Tri-ax shifter
Exedy Stage 2 clutch
Exedy flywheel
Machwon Jerry is offline   Reply With Quote
Old 10-29-2017, 05:32 PM   #2
Machwon Jerry
Registered User
 
Machwon Jerry's Avatar
 
Join Date: Oct 2017
Location: Jacksonville, Florida
Posts: 14
Re: Intake Spacer Dyno Results

I forgot to mention this testing was done with a 3/8" spacer.
__________________
Eagle 301 stroker kit
Pocket ported heads
Comp Cams 106100s
Roy's 3/8" Intake Spacer
K&N CAI
MAC LTs & O/R Prochamber
Steeda UDPs
Steeda Tri-ax shifter
Exedy Stage 2 clutch
Exedy flywheel
Machwon Jerry is offline   Reply With Quote
Old 10-30-2017, 10:16 PM   #3
311-420
M-112 Mach 1
 
311-420's Avatar
 
Join Date: Sep 2007
Location: DFW, TX
Posts: 6,515
Re: Intake Spacer Dyno Results

Seems worthwhile to me!

Care to be more specific about your setup?
__________________
04 Oxford White // 5spd, IUP
Eaton @ 6psi, Longtubes
Built/3.73 rear, TSM tune
452/409
311-420 is offline   Reply With Quote
Old 11-01-2017, 02:37 PM   #4
sutyak
it's soo-tack
 
sutyak's Avatar
 
Join Date: Nov 2002
Location: Fairmont, WV
Posts: 2,022
Re: Intake Spacer Dyno Results

Were runs 3,4,5,6 done in order? If so, I see no appreciable gain.
__________________
mark
2004 DSG Mach 1. Built motor. Turbo. 667whp
2006 Sonic Blue Focus. Built motor. Turbo. 12.4 @ 115mph (sold)
2003 DSG Mach 1. 12.65 @ 106 (sold)
sutyak is offline   Reply With Quote
Old 11-01-2017, 04:19 PM   #5
DSG2003Mach1
700 HP Mach
 
DSG2003Mach1's Avatar
 
Join Date: Nov 2003
Location: Orlando, FL
Posts: 7,992
Re: Intake Spacer Dyno Results

ya a little explanation on the numbers would be nice. Theres one pull thats ~10hp/tq lower than all the rest. The others are within about 1%, Id have to imagine thats in the window of margin for error on a dyno
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc...

'12 F150 FX2 Supercrew with Ecoboost daily beater
DSG2003Mach1 is offline   Reply With Quote
Old 11-01-2017, 06:13 PM   #6
311-420
M-112 Mach 1
 
311-420's Avatar
 
Join Date: Sep 2007
Location: DFW, TX
Posts: 6,515
Re: Intake Spacer Dyno Results

Going from the first run (which I'm assuming is without the spacer) to the last run (with the spacer), it looks like +8hp and +8tq unless my eyes are playing tricks on me..
__________________
04 Oxford White // 5spd, IUP
Eaton @ 6psi, Longtubes
Built/3.73 rear, TSM tune
452/409
311-420 is offline   Reply With Quote
Old 11-02-2017, 08:47 AM   #7
sutyak
it's soo-tack
 
sutyak's Avatar
 
Join Date: Nov 2002
Location: Fairmont, WV
Posts: 2,022
Re: Intake Spacer Dyno Results

Quote:
Originally Posted by 311-420 View Post
Going from the first run (which I'm assuming is without the spacer) to the last run (with the spacer), it looks like +8hp and +8tq unless my eyes are playing tricks on me..
Except run #2 was the highest, which would be run 2 of no spacer.
__________________
mark
2004 DSG Mach 1. Built motor. Turbo. 667whp
2006 Sonic Blue Focus. Built motor. Turbo. 12.4 @ 115mph (sold)
2003 DSG Mach 1. 12.65 @ 106 (sold)
sutyak is offline   Reply With Quote
Old 11-02-2017, 10:33 AM   #8
311-420
M-112 Mach 1
 
311-420's Avatar
 
Join Date: Sep 2007
Location: DFW, TX
Posts: 6,515
Re: Intake Spacer Dyno Results

Quote:
Originally Posted by sutyak View Post
Except run #2 was the highest, which would be run 2 of no spacer.
In that case, a spacer is worth nothing, atleast not on this particular car for whatever reason, and the power/tq fluctuations were due entirely to coolant, oil and atmospheric changes.

However, I think OP may be mistaken either about how many pulls of each were made or how many of each pull was actually recorded on that sheet. It makes better sense to me that only the first pull on that sheet was a baseline and the others were with the spacer installed. The numbers got slightly higher, as would be expected, and were all on top of one another showing a consistent change.

This thread really seems more like an exercise in speculation unless OP can clear some things up.
__________________
04 Oxford White // 5spd, IUP
Eaton @ 6psi, Longtubes
Built/3.73 rear, TSM tune
452/409
311-420 is offline   Reply With Quote
Old 11-03-2017, 08:35 PM   #9
rich1
AUTOMACHTIC
 
rich1's Avatar
 
Join Date: Oct 2007
Location: RTP/ N.C.
Posts: 4,784
Re: Intake Spacer Dyno Results

Quote:
Originally Posted by 311-420 View Post
Going from the first run (which I'm assuming is without the spacer) to the last run (with the spacer), it looks like +8hp and +8tq unless my eyes are playing tricks on me..
I got 9hp and 9 tq results at Pro-Dyno when I installed my Roys 3/8 spacer Dan was surprised that the spacer worked too .
__________________
UPGRADES... Borla SS Catback , Steeda Underdrives , Steeda Strut Brace , HPM Lower K Brace , L /C Arms , U /C Arms , HPM PanHard Bar, K&N FRPK 2, GOODYEAR GT1 , MRT- H-Pipe , JLT VaporTraps , SLP-12'" Tips! , FRPP Shorty 1 5/8 Headers , Brembo D/S & PBR D/S Rotors ,FRPP Alum.DS ,Roys 3/8 Spacer , SVT Focus 255 pump SCTsw Chip PRO-DYNOjet NA 300.01hp /315tq (Auto) ,Innovate W/B ,Compucar Wet Kit (90jet) + Heater and E Gauge * 360 hp/385tq 12.5 -1/4 @112
rich1 is offline   Reply With Quote
Old 11-04-2017, 01:19 PM   #10
Machwon Jerry
Registered User
 
Machwon Jerry's Avatar
 
Join Date: Oct 2017
Location: Jacksonville, Florida
Posts: 14
Re: Intake Spacer Dyno Results

Okay guys sorry i haven't responded sooner runs were done in order 3,4,5, and 6 so there was no real power gain. I think run 3 was just garbage and my tuner didn't pull hard or something. Runs 3 and 4 were done with 301 Eagle stroker kit 9.1:1 compression, pocket port on the heads, comp cams 106100s w/ beehive springs and Comp cam gears, MAC LTs and O/R Prochamber w/ stock catback and a K&N CAI. Runs 5 and 6 were w/ same mods except i put the spacer on while the car was cooling down. All runs were same day. My A/F did go from about 12.5-12.8 all the way up to over 14. I think as far as Hp goes its not worth it, but it does make the shaker look better. I also put 2 nuts under the front part of the shaker bracket to level it out after. I am wondering what would happen if we change the tune up a little and give it some more fuel.
__________________
Eagle 301 stroker kit
Pocket ported heads
Comp Cams 106100s
Roy's 3/8" Intake Spacer
K&N CAI
MAC LTs & O/R Prochamber
Steeda UDPs
Steeda Tri-ax shifter
Exedy Stage 2 clutch
Exedy flywheel
Machwon Jerry is offline   Reply With Quote
Old 11-04-2017, 01:22 PM   #11
Machwon Jerry
Registered User
 
Machwon Jerry's Avatar
 
Join Date: Oct 2017
Location: Jacksonville, Florida
Posts: 14
Re: Intake Spacer Dyno Results

I forgot all runs had Steeda UDPs as well. Other mods are Mishimoto radiator, Edelbrock water pump, Reishe Performance thermostat, SVT Focus fuel pump, Exedy lighweight flywheel and stage 2 clutch, Steeda Tri-ax shifter. I may have forgot some more, but thats what i can remember off the top of my head.
__________________
Eagle 301 stroker kit
Pocket ported heads
Comp Cams 106100s
Roy's 3/8" Intake Spacer
K&N CAI
MAC LTs & O/R Prochamber
Steeda UDPs
Steeda Tri-ax shifter
Exedy Stage 2 clutch
Exedy flywheel
Machwon Jerry is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 07:31 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<