Nitrous recommendations ? - 2003-04 Mach 1 Registry Owners Club

5.0 drag racer · 03-30-2009, 10:30 AM

Ok all, i have gone the route of all the normal bolt ons and 4.30 rear end gears etc. I have always been a nitrous junkie with my former 11 sec bottle fed 88 Gt. now i want to spray my mach 1.

what are your recommendations for a kit and is it possible for a dry kit ? or only a wet kit becuase of the fuel system configuration. I will buy a window switch as well as i had one in the gt and was a must have as well as a bottle heater.

Any input is appreciated with yoru results and long term opionions from experience.

looking for only a 100 to 150 shot no more at this time. will start small with 100 first.

thanks all in advance.

any pix would be great too.

cheers

2k4mach · 03-30-2009, 10:38 AM

nx stage 1 efi wet kit
gen x2 accessory kit.
MSD digital window switch.

MachSoldier · 03-30-2009, 12:21 PM

did just what you are talking about with my mach. ran it yesterday and got a 12.2. I am not the best of drivers so I am sure that it will run 11's but I cant launch it to save my life.

Anyways just like 2k4Mach said. Thats what I have and it runs pretty **** good.

3150Mach1 · 03-30-2009, 03:36 PM

Quote:

Originally Posted by 2k4mach

nx stage 1 efi wet kit
gen x2 accessory kit.
MSD digital window switch.

Thats what you need.

11.78 on a BX 100 wet shot in my slowmatic mach.

I also suggest a wideband a/f guage and a hand held tuner that will let you change fuel and timing settings for the spray.

5.0 drag racer · 03-31-2009, 10:07 AM

Quote:

Originally Posted by 03Mach150BP

Thats what you need.

11.78 on a BX 100 wet shot in my slowmatic mach.

I also suggest a wideband a/f guage and a hand held tuner that will let you change fuel and timing settings for the spray.

Thanks, i will more than likely do the wideband, i currently have a SCT2 tuner so good to go there.

5.0 drag racer · 03-31-2009, 10:08 AM

thanks to all that have posted so far.

FourValveGT · 03-31-2009, 06:31 PM

The wilson kit is a great deal for the shot, but if you want to go big in the end TNT is the only way to go, best solenoids and nozzle I have seen.

FourValveGT · 03-31-2009, 08:33 PM

Quote:

Originally Posted by Mach1Marauder

He ain't going big.

Thats why i said Wilson in there old man. I also said in the end if he wants to go big THEN go TNT. I hope you got to read through that whole thing you narcoleptic mach 1 wanna be driving old man. Low balling zzzzzzzzzzzzzzz.......

Phil · 03-31-2009, 08:45 PM

Don't do it!!!

FourValveGT · 03-31-2009, 08:56 PM

Quote:

Originally Posted by Mach1Marauder

You're getting THUMPED!.

............not a "love tap" like I gave Clint Friday. I only knocked him back 3ft.

Dont make me take you down AGAIN

JMachOne · 03-31-2009, 09:12 PM

Installing Zex Wet Kit on my Mach 1 right now.

Starting with 125 shot on stock internals

Finishing the install this weekend and dropping it off for a tune this week.

Can't wait to see what it has

FourValveGT · 03-31-2009, 09:17 PM

Quote:

Originally Posted by Mach1Marauder

Next time I'll just snap your neck.

Anyone ever tell you your the same in person as on the forums. All talk
Coulda Shoulda Woulda dont count

JMachOne · 03-31-2009, 09:22 PM

Quote:

Originally Posted by Mach1Marauder

baby shot

On stock internals

I am going for a 150 shot on the track for laughs

2k4mach · 03-31-2009, 09:45 PM

Quote:

Originally Posted by Mach1Marauder

**** dude! You like to dig your grave deep, huh?

I KEEEEEEL YOU

FourValveGT · 03-31-2009, 09:47 PM

Quote:

Originally Posted by 2k4mach

I KEEEEEEL YOU

Looks like I got Mark on my side.

Old Man

2k4mach · 03-31-2009, 10:03 PM

Quote:

Originally Posted by FourValveGT

Looks like I got Mark on my side.

Old Man

he tryed telling me he whipped out his "buffalo skinner" when Dan made him drop a load in his depends the other night.

i can just father time pinching a loaf then 10 minutes later getting teh "buffalo skinner" out saying "I KEEEEEEEEEL YOU"

MACHDADDY1 · 04-04-2009, 09:30 AM

Quote:

Originally Posted by Mach1Marauder

Yes.......on stock internals.
Zex rates their shot at the crank................not to the wheels. A 125 Zex shot IS a baby shot.

I ran a 10.87 @ 127mph on that zex baby shot.............so if these guys would pay more attention to the rest of the car they wouldnt need a even a zex 150 shot to get it done.

03-30-2009, 10:30 AM	#1
5.0 drag racer Registered User Join Date: Apr 2008 Location: Littleton, Ma Posts: 141	Nitrous recommendations ? Ok all, i have gone the route of all the normal bolt ons and 4.30 rear end gears etc. I have always been a nitrous junkie with my former 11 sec bottle fed 88 Gt. now i want to spray my mach 1. what are your recommendations for a kit and is it possible for a dry kit ? or only a wet kit becuase of the fuel system configuration. I will buy a window switch as well as i had one in the gt and was a must have as well as a bottle heater. Any input is appreciated with yoru results and long term opionions from experience. looking for only a 100 to 150 shot no more at this time. will start small with 100 first. thanks all in advance. any pix would be great too. cheers

03-30-2009, 10:38 AM	#2
2k4mach LuLz Join Date: Dec 2003 Location: Cedar Park, TX Posts: 19,294	Re: Nitrous recommendations ? nx stage 1 efi wet kit gen x2 accessory kit. MSD digital window switch. __________________ 11 Sterling gray GT500 coupe 08 Silver Z06 1058rwhp/1073rwt @ 15psi 14 Silver Q50S Vortech blown 04 DSG Mach 1 (stolen) 03 OW Mach 1 (sitting in a field rotting away)

03-30-2009, 12:21 PM	#3
MachSoldier Registered User Join Date: Jan 2008 Location: Fort Bragg, NC Posts: 170	Re: Nitrous recommendations ? did just what you are talking about with my mach. ran it yesterday and got a 12.2. I am not the best of drivers so I am sure that it will run 11's but I cant launch it to save my life. Anyways just like 2k4Mach said. Thats what I have and it runs pretty **** good. __________________ 03 DSG Mach 5 spd Mods: SLP LM1 Catback, Pypes OR X-pipe, K&N drop in, NX 125 Shot, SCT flip chip w/ Custom tune from Competition Auto, M/T ET Streets 275/35/17, H&R SS springs, FRPP Cobra Diff, 31 Spline Moser Axles, 4.10 Gears Best ET: 11.9 @ 116

03-31-2009, 10:08 AM	#6
5.0 drag racer Registered User Join Date: Apr 2008 Location: Littleton, Ma Posts: 141	Re: Nitrous recommendations ? thanks to all that have posted so far.

03-31-2009, 06:31 PM	#7
FourValveGT In the garage Join Date: Nov 2007 Location: Phoenix, AZ Posts: 116	Re: Nitrous recommendations ? The wilson kit is a great deal for the shot, but if you want to go big in the end TNT is the only way to go, best solenoids and nozzle I have seen.

03-31-2009, 08:45 PM	#9
Phil Nitrous Junkie Join Date: Jul 2003 Location: Ohio Posts: 7,299	Re: Nitrous recommendations ? Don't do it!!! __________________ Phil PRB Machining, LLC http://www.prbmachining-absdeleteman...com/index.html Performance mods by Jeff Chambers, the owner/tuner of CRT Performance in Norwalk, Ohio http://www.crt-performance.com/

03-31-2009, 09:12 PM	#11
JMachOne Registered User Join Date: Sep 2007 Location: Manchester, MO Posts: 52	Re: Nitrous recommendations ? Installing Zex Wet Kit on my Mach 1 right now. Starting with 125 shot on stock internals Finishing the install this weekend and dropping it off for a tune this week. Can't wait to see what it has __________________ 03 Black Mach 1 1 of 1,611 Mods: Zex Wet Kit, JLT RAI, Magnaflow Magnapacks, BBK LT, BBK O/R H, Fidanaza Alum. Flywheel, H&R Super Sports, Steeda C/C Plates

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)