2003-04 Mach 1 Registry Owners Club  

Best Mustang Parts

Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Power Adders

Power Adders Superchargers, Turbos, Nitrous, etc...

Reply
 
Thread Tools Display Modes
Old 03-15-2015, 03:13 PM   #326
blk 04 mach 1
Registered User
 
blk 04 mach 1's Avatar
 
Join Date: Dec 2008
Location: Hallsville Texas
Posts: 953
Re: Official Procharger HP/TQ/mods thread:

any updates to the D1 Procharger setups? looking to get in to a D! pro charger. not sure of the finish yet polished or just satin. what about the upgraded bearings is it worth it? are they quieter? Thanks!
blk 04 mach 1 is offline   Reply With Quote
Old 05-26-2015, 04:29 PM   #327
Nekasrof
Hillclimb Extraodinaire
 
Nekasrof's Avatar
 
Join Date: Aug 2004
Location: Perkiomenville, PA
Posts: 2,590
Re: Official Procharger HP/TQ/mods thread:

FINALLY have real numbers. Done on a MustangDyno at factory settings.

HP: 541.6 @ 6236rpm w/correction factor: 536.8
TQ: 486.2 @ 4763rpm w/correction factor: 481.9
You can calculate those numbers for DynoJet comparison.
AFR: 11.8
Timing: 19deg(tune setting is 18 but +1 for low temps)
Boost lvl: 14lbs
IAT: 80deg

D1SC w/4" pulley and intercooled
IW 15% OD
80lb FRPP injectors
Twin Walbro 400lph
4.10 gears
50/50 fuel mixture of Sunoco 93/VP MS109
60lbs fuel pressure at idle w/vaccum disconnected
Coolant temp 170+
Oil temp 170
Pump voltage 13.6+/-

I'm waiting for the data log to be emailed. Don't like the format on the print out.

When I got the car dyno'd last year, the tuner broke and no data log/dyno sheet was given. We tuned off my wideband and it looked pretty good.
Over the weekend, at Summit Point, on one of the straights, I thought I saw 12.2 on the wideband. I was panicked. So I went back to trailer and added some more race fuel to be safe as I knew I was going to dyno the car today. Sure enough, my wideband read correctly. We added 3lbs of fuel and BINGO, 11.8 on the last couple of pulls. I'm ready for the rest of the season now!!!!!

When I get the data log, I'll try to put it up here.
__________________
Motor + Procharger + driver = Baddest hillclimbing Mach 1 in the country
Mustang dyno: 538hp/481tq @ 14lbs/19deg timing
DynoJet comparison: 600hp/539tq

Looking for more hillclimbers!
Nekasrof is offline   Reply With Quote
Old 05-26-2015, 09:16 PM   #328
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,808
Re: Official Procharger HP/TQ/mods thread:

Awesome numbers ^^^^
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 09-09-2015, 11:43 PM   #329
blk 04 mach 1
Registered User
 
blk 04 mach 1's Avatar
 
Join Date: Dec 2008
Location: Hallsville Texas
Posts: 953
Re: Official Procharger HP/TQ/mods thread:

very good numbers.... Thinking about a F1A portrayer now.... thoughts?
blk 04 mach 1 is offline   Reply With Quote
Old 09-10-2015, 01:30 AM   #330
01yellerCobra
Registered User
 
Join Date: Jan 2013
Location: San Diego, CA
Posts: 1,106
An F1A is loud. No way around it. If you pair it with an open BOV they will hear you coming for miles. That being said I loved my F1A. I had it pullied to max out around 65k rpm which showed 19psi on the boost gauge. I miss it sometimes.
__________________
New Ride:
2004 Mystichrome Cobra-Accufab SBTB and plenum, Steeda 2.8" upper, Bassani X, Borla Stingers, Mcleod RXT, MGW shifter, Level 5 halfshafts, chrome FR500's, Stiffler's FIT system and DS safety loop, GT pumps, BA3000, tuned by owner
01yellerCobra is offline   Reply With Quote
Old 09-13-2015, 04:21 PM   #331
monsterbrad
Registered User
 
Join Date: Jun 2015
Location: erie Pa
Posts: 110
Re: Official Procharger HP/TQ/mods thread:

ok after reading the entire thread again
Anybody go to the roots blower after these
Is it worth it on the Mach ??
This blower system keeps the shacker in place with no mods and can be removed for a resale easier if needed.
Let me know guys
thanks
monsterbrad is offline   Reply With Quote
Old 09-14-2015, 11:10 AM   #332
Procharged2k3
Registered User
 
Procharged2k3's Avatar
 
Join Date: Jun 2015
Location: St. Louis, MO
Posts: 277
Re: Official Procharger HP/TQ/mods thread:

Head unit: P1SC w/ intercooler

Boost pressure: 6 PSI

Other mods:
-KB Boost-A-Pump on stock pump
-60 lb injectors
-UPR catted X-pipe
-Flowmasters

Wheel HP: 448 @ 6210 RPM (on a 94 degree day)
Wheel torque: 418 @ 4890 RPM

My tuner said he could probably get another 30 HP out of it by playing with the timing some more, but I like some margin for error.
Procharged2k3 is offline   Reply With Quote
Old 09-14-2015, 07:46 PM   #333
311-420
#6956
 
311-420's Avatar
 
Join Date: Sep 2007
Location: +Ä◊♤$
Posts: 6,743
Re: Official Procharger HP/TQ/mods thread:

Quote:
Originally Posted by Procharged2k3 View Post
Head unit: P1SC w/ intercooler

Boost pressure: 6 PSI

Other mods:
-KB Boost-A-Pump on stock pump
-60 lb injectors
-UPR catted X-pipe
-Flowmasters

Wheel HP: 448 @ 6210 RPM (on a 94 degree day)
Wheel torque: 418 @ 4890 RPM

My tuner said he could probably get another 30 HP out of it by playing with the timing some more, but I like some margin for error.
Real stout for 6psi! Dayum.
__________________
04 Oxford White
5spd IUP
Eaton 452/409
311-420 is offline   Reply With Quote
Old 09-15-2015, 11:30 AM   #334
Procharged2k3
Registered User
 
Procharged2k3's Avatar
 
Join Date: Jun 2015
Location: St. Louis, MO
Posts: 277
Re: Official Procharger HP/TQ/mods thread:

Yeah I couldn't believe it. My secret weapon is the best Ford tuner in the midwest, Bob Monks @ STL Mustangs! Although it might be more like 7 PSI now, since we removed the intake tube and put mesh screen directly on the blower. No pulley change though. I'll watch my boost gauge next time I get on it.

Went to a car meet on Sunday, got into a run with a 2006 Gallardo Spyder (NOT on public roads!!) and he just couldn't seem to pull away from me so I'm happy! Can't feel good to have a $200k car and not be able to outrun a 12 year old Mustang.

Later I found out they're just 500 HP or so at the crank, but I still get to say I hung with a Lambo!

EDIT: Tested it tonight, boost never goes past 6 PSI.

Last edited by Procharged2k3; 09-16-2015 at 12:30 AM.
Procharged2k3 is offline   Reply With Quote
Old 10-13-2015, 02:23 PM   #335
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,808
Re: Official Procharger HP/TQ/mods thread:

Retune.. 454/416 @7.90 psi pull to 6250 due to the fact I now have 141,000 miles on stock motor!!

__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq

Last edited by not a gt; 10-13-2015 at 09:44 PM.
not a gt is offline   Reply With Quote
Old 10-13-2015, 05:48 PM   #336
311-420
#6956
 
311-420's Avatar
 
Join Date: Sep 2007
Location: +Ä◊♤$
Posts: 6,743
Re: Official Procharger HP/TQ/mods thread:

Good numbers Larry Any idea on why it wasn't trapping well?
__________________
04 Oxford White
5spd IUP
Eaton 452/409
311-420 is offline   Reply With Quote
Old 10-13-2015, 09:43 PM   #337
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,808
Re: Official Procharger HP/TQ/mods thread:

Quote:
Originally Posted by 311-420 View Post
Good numbers Larry Any idea on why it wasn't trapping well?
We are thinking it was the rev limiter being at 6000, the 3.73 email tune definitely did not like going thru cyberspace
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 05-04-2016, 09:16 AM   #338
slojunk91
Registered User
 
slojunk91's Avatar
 
Join Date: Feb 2013
Location: NEW YORK HIGHEST TAXES IN AMERICA
Posts: 603
Re: Official Procharger HP/TQ/mods thread:

Stock Bottom End: Yes

Head Unit: P1SC

Pulley Size & Boost Level: 3.80 & 9 lbs @ 6200 rpm

Fuel System: 42 lbs, 290 lph, & HPX slot MAF

Tuner: SCT X3, Pro Edge Dyno Tuning

Other Notables: ARH 1 3/4 LT, Off Road X, 3/8" Intake Spacer, Accufab TB, Innovators West Stock dia. Dampner, MSD coils, NGK TR6

RWHP/RWTQ: 460 rwhp, 408 rwtq
slojunk91 is offline   Reply With Quote
Old 09-12-2016, 09:28 PM   #339
gonemad
Registered User
 
gonemad's Avatar
 
Join Date: Oct 2010
Location: thompson oh
Posts: 332
Re: Official Procharger HP/TQ/mods thread:

Stock Bottom End: Yes

Head Unit: P1SC

Pulley Size & Boost Level: 3.7 & 8.5 lbs @ 6200 rpm

Fuel System: 60 lbs, 340lph, & SCT BA5000 slot MAF

Tuner : SCT XCAL 3

Other Notables: See sig

RWHP/RWTQ: 485 rwhp, 440tq

Ran out of fuel at 6200, going back for a re-tune with fuel pump wire upgrade. HP was still climbing VERY hard when pull was cut. I think I'm gonna chance the bottom end and see what it does around 6800. 520 should be easy. And yes it's a mustang dyno and a pretty stingy one.
__________________
2004 comp orange, cobra cams, kooks LTs, cobra diff, 31 spline moser, 4.30s, TKO500 promotion clutch/fly, FMS driveshaft, JLT CAI, na svt ported intake, UPR adj rear Team Z front, full 3" magnaflow X and catback. 11.97@115 n/a 10.89@125 on 150 shot.
89 coupe stock bottom end on3 70mm. 10.02@134
gonemad is offline   Reply With Quote
Old 09-16-2016, 09:47 PM   #340
USMC1142
Registered User
 
USMC1142's Avatar
 
Join Date: Jul 2012
Location: Vancouver, WA
Posts: 8
Re: Official Procharger HP/TQ/mods thread:

Update

Bottom end: dss 5.0 stroker kit 9.0-1

Head unit: d1sc

Pulley: 15% OD crank 3.8 in supercharger pulley 11-12 psi

Fuel system: lethal performance budget return, twin aero motive 340lph, 60lb injectors. 05+ slot maf

Tuned by fast specialties in Vancouver, WA

Cam spec by NAsvt, mac long tube, catted x pipe, Borla cat back

540 rwhp 495 rwtq

Going to finish converting to an 8 rib than get it re tuned with a 3.55 in pulley in a few months
__________________
Built 9.5-1 motor with d1 pro charger
540 hp 495tq
11.02 @129

Last edited by USMC1142; 08-03-2017 at 03:34 PM.
USMC1142 is offline   Reply With Quote
Old 09-21-2016, 02:11 PM   #341
BONESTOCK
Registered User
 
Join Date: Jul 2004
Location: MA
Posts: 1,951
Re: Official Procharger HP/TQ/mods thread:

Quote:
Originally Posted by USMC1142 View Post
Update

Bottom end: dss 5.0 stroker kit 9.0-1

Head unit: d1sc

Pulley: 15% OD crank 3.8 in supercharger pulley

Fuel system: lethal performance budget return, twin aero motive 340lph, 60lb injectors. 05+ slot maf

Tuned by fast specialties in Vancouver, WA

Cam spec by NAsvt, mac long tube, catted x pipe, Borla cat back

540 rwhp 495 rwtq

Going to finish converting to an 8 rib than get it re tuned with a 3.55 in pulley in a few months
What, exactly, did you get from DSS? I sent them an email. Waiting to hear back. I'm looking to turn my Procharger up as well but need the forged bits inside the engine first.
__________________
2004 Torch Red Procharged Mach 1
2003 Torch Red Mach 1
BONESTOCK is offline   Reply With Quote
Old 09-21-2016, 05:11 PM   #342
USMC1142
Registered User
 
USMC1142's Avatar
 
Join Date: Jul 2012
Location: Vancouver, WA
Posts: 8
Re: Official Procharger HP/TQ/mods thread:

Quote:
Originally Posted by BONESTOCK View Post
What, exactly, did you get from DSS? I sent them an email. Waiting to hear back. I'm looking to turn my Procharger up as well but need the forged bits inside the engine first.
http://shop.dssracing.com/5_0_Modula..._p/ra5.0x5.htm

Went with -15cc pistons which they said should put me at 9.3-1 engine builder said it was 9-1 though. Also used gapless rings
__________________
Built 9.5-1 motor with d1 pro charger
540 hp 495tq
11.02 @129
USMC1142 is offline   Reply With Quote
Old 10-24-2016, 04:29 PM   #343
BONESTOCK
Registered User
 
Join Date: Jul 2004
Location: MA
Posts: 1,951
Re: Official Procharger HP/TQ/mods thread:

Quote:
Originally Posted by USMC1142 View Post
http://shop.dssracing.com/5_0_Modula..._p/ra5.0x5.htm

Went with -15cc pistons which they said should put me at 9.3-1 engine builder said it was 9-1 though. Also used gapless rings
Thank you thank you!
__________________
2004 Torch Red Procharged Mach 1
2003 Torch Red Mach 1
BONESTOCK is offline   Reply With Quote
Old 09-24-2017, 01:09 PM   #344
FenixFallen
Newb
 
FenixFallen's Avatar
 
Join Date: Nov 2011
Location: Barre, Vermont
Posts: 203
Re: Official Procharger HP/TQ/mods thread:

Just got my setup tuned last week. Tuner had to back off the timing quite a bit he said to keep the numbers safer. I've got a forged internal stroker waiting to go in but I need different cams (it has turbo cams currently) and a built transmission before I tackle the engine swap.


Stock bottom end: YES

Head unit: D1SC

Pulley size and boost level: 4.15 pulley, 8.9psi @6100rpm

Fuel system: 39lb injectors, VMP5000 slot style MAF, Lethal Performance budget return style fuel system, dual Walbro 255lph pumps

Tuner: Xcal3 tuned by Performance Dyno in Loudon, NH

Other notable mods: Accufab 60mm TB, ported intake, 3/8 intake spacer, MAC long tubes, offroad midpipe,

RWHP/RWTQ: 483 rwhp @6100 451 rwtq @4900

__________________
Black 2003 Mach 1, 483hp/451tq @6100 8.9psi
-Stock longblock, stock transmission, Procharger D1SC 4.15" pulley, Accufab 60mm TB, P/P intake manifold, full MAC exhaust, return style fuel system, Maximum Motorsports/Steeda suspension, Torsen T2R 31 spline diff, Mickey Thompson SC-5 18" with Nittos.

Red 2007 Focus ST, daily driver, 236hp/234tq @10psi
-FSWerks turbo, Cosworth intake manifold, FSWerks Stealth exhaust, FRPP lowering springs
FenixFallen is offline   Reply With Quote
Old 10-16-2018, 10:27 PM   #345
bristol16
Registered User
 
Join Date: May 2018
Location: NH
Posts: 2
Re: Official Procharger HP/TQ/mods thread:

Stock bottom end: YES

Head unit: D1SC

Pulley size and boost level: Not sure on pulley size, requested ~8psi when I ordered it to keep it under 500rwhp

Fuel system: Deatschwerks 340lph pump, 47lb Ford Performance injectors

Tuner: Custom dyno tuned...flashed to the car using an SCT Tuner

Other notable mods: BBK long tubes, BBK catted H-pipe, SLP LM2 cat back

RWHP: Asked the tuner to keep it below 500rwhp...car dyno'd 460rwhp

Last edited by bristol16; 10-21-2018 at 07:15 PM. Reason: typo
bristol16 is offline   Reply With Quote
Old 10-17-2018, 11:50 AM   #346
311-420
#6956
 
311-420's Avatar
 
Join Date: Sep 2007
Location: +Ä◊♤$
Posts: 6,743
Re: Official Procharger HP/TQ/mods thread:

Quote:
Originally Posted by FenixFallen View Post
Just got my setup tuned last week. Tuner had to back off the timing quite a bit he said to keep the numbers safer. I've got a forged internal stroker waiting to go in but I need different cams (it has turbo cams currently) and a built transmission before I tackle the engine swap.


Stock bottom end: YES

Head unit: D1SC

Pulley size and boost level: 4.15 pulley, 8.9psi @6100rpm

Fuel system: 39lb injectors, VMP5000 slot style MAF, Lethal Performance budget return style fuel system, dual Walbro 255lph pumps

Tuner: Xcal3 tuned by Performance Dyno in Loudon, NH

Other notable mods: Accufab 60mm TB, ported intake, 3/8 intake spacer, MAC long tubes, offroad midpipe,

RWHP/RWTQ: 483 rwhp @6100 451 rwtq @4900

Nice. How has it performed for you? Are you having to shift at 6k? I bet that takes some restraint.
__________________
04 Oxford White
5spd IUP
Eaton 452/409
311-420 is offline   Reply With Quote
Old 10-17-2018, 11:53 AM   #347
311-420
#6956
 
311-420's Avatar
 
Join Date: Sep 2007
Location: +Ä◊♤$
Posts: 6,743
Re: Official Procharger HP/TQ/mods thread:

Quote:
Originally Posted by bristol16 View Post
Stock bottom end: YES

Head unit: D1SC

Pulley size and boost level: Not sure on pulley size, requested ~8psi when I ordered it to keep it under 500rwhp

Fuel system: Deatshwerks 340lph pump, 47lb Ford Performance injectors

Tuner: Custom dyno tuned...flashed to the car using an SCT Tuner

Other notable mods: BBK long tubes, BBK catted H-pipe, SLP LM2 cat back

RWHP: Asked the tuner to keep it below 500rwhp...car dyno'd 460rwhp
Solid. What are your impressions?
__________________
04 Oxford White
5spd IUP
Eaton 452/409
311-420 is offline   Reply With Quote
Old 10-17-2018, 10:43 PM   #348
not a gt
Registered User
 
not a gt's Avatar
 
Join Date: Mar 2007
Location: Waaayy out in the country,leave your GPS at home!
Posts: 4,808
Re: Official Procharger HP/TQ/mods thread:

Quote:
Originally Posted by bristol16 View Post
Stock bottom end: YES

Head unit: D1SC

Pulley size and boost level: Not sure on pulley size, requested ~8psi when I ordered it to keep it under 500rwhp

Fuel system: Deatshwerks 340lph pump, 47lb Ford Performance injectors

Tuner: Custom dyno tuned...flashed to the car using an SCT Tuner

Other notable mods: BBK long tubes, BBK catted H-pipe, SLP LM2 cat back

RWHP: Asked the tuner to keep it below 500rwhp...car dyno'd 460rwhp
HELL YEA..GREAT NUMBERS..CONGRATS !!! Lol, funny asked tuner to RESTRICT HP, doesn't everyone want that problem lol !!!!
__________________
2003 DSG Mach 1-03 Cobra Term/T56 swap:
2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear
Tuned by B.Kurgan
601Hp/558/Tq
not a gt is offline   Reply With Quote
Old 10-18-2018, 10:39 AM   #349
bristol16
Registered User
 
Join Date: May 2018
Location: NH
Posts: 2
Re: Official Procharger HP/TQ/mods thread:

Quote:
Originally Posted by 311-420 View Post
Solid. What are your impressions?
Iíve been happy with it. Iíve owned a few turbo cars and some other toys but this is the first car Iíve had that is supercharged. The D1SC is quieter than I expected, even with the louder ďstock cutĒ gears in it. Power delivery is definitely smoother than the turbo cars Iíve driven and it pulls really really hard up top...never drops off at all. Tuner said he felt like it may be staring to break up just before redline so I am going to replace the plugs and go one step colder to help out the motor. With the exhaust mods Iím not sneaking around anywhere but the car does scoot right along.

Quote:
Originally Posted by not a gt View Post
HELL YEA..GREAT NUMBERS..CONGRATS !!! Lol, funny asked tuner to RESTRICT HP, doesn't everyone want that problem lol !!!!
Yeah no kidding! I have no doubt that a D1SC is capable of more, but most everything I read said results may vary over 500 so I wanted to keep it down until I build the motor, if I ever do. I never asked him how much higher he thought it would go, be interesting to know what the limit is. These DOHC engines also rev decently higher than my LS1 did, kinda weird waiting so long to shift.
bristol16 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:58 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<