2003-04 Mach 1 Registry Owners Club  

Best Mustang Parts

Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Power Adders

Power Adders Superchargers, Turbos, Nitrous, etc...

Reply
 
Thread Tools Display Modes
Old 03-12-2007, 07:03 PM   #26
lxh89
Registered User
 
lxh89's Avatar
 
Join Date: Jan 2003
Location: Houston, Tx
Posts: 1,530
Re: wiring diagram for nitrous setup

Quote:
Originally Posted by 04azuremach View Post
What did you hook the arming switch and window switch up to for the 12v source? I'm an electronics n00b.
Tapped into the accessory power lead. Don't need many amps to power the window switch or the low amp side of the relay. For the bottle heater relay, I tapped into the defroster power lead.

Tony
__________________
2015 Ruby Red Mustang GT Premium
Bone Stock

03 Oxford White Mach 1 - SOLD
1.72 60',10.932@131.60MPH, 3800# Raceweight
lxh89 is offline   Reply With Quote
Old 03-12-2007, 07:05 PM   #27
dantheratman
Registered User
 
dantheratman's Avatar
 
Join Date: Jan 2006
Location: here,here
Posts: 592
Re: MSD Digital Window Switch/Nitrous wiring setup

which msd switch are you guys using???... rpm converter required??
dantheratman is offline   Reply With Quote
Old 03-12-2007, 08:26 PM   #28
lxh89
Registered User
 
lxh89's Avatar
 
Join Date: Jan 2003
Location: Houston, Tx
Posts: 1,530
Re: MSD Digital Window Switch/Nitrous wiring setup

Quote:
Originally Posted by dantheratman View Post
which msd switch are you guys using???... rpm converter required??
Using the MSD Digital and no converter is required.

Tony
__________________
2015 Ruby Red Mustang GT Premium
Bone Stock

03 Oxford White Mach 1 - SOLD
1.72 60',10.932@131.60MPH, 3800# Raceweight
lxh89 is offline   Reply With Quote
Old 03-12-2007, 09:53 PM   #29
grey03mach1
Speed Addict
 
grey03mach1's Avatar
 
Join Date: Jan 2005
Location: Jena,Louisiana
Posts: 1,393
Re: MSD Digital Window Switch/Nitrous wiring setup

I finally got it. The only problem I have now is that my bottle warmer is hooked up with the window switch and only comes on between 3000-6500 rpms. haha I bought another relay that I will use for the bottle warmer. I'll run it tomorrow. Thanks for the help fellas!
__________________
My 2003 DSG Mach 1Sold

2001 Formula
grey03mach1 is offline   Reply With Quote
Old 11-07-2007, 03:14 PM   #30
BT03mach-1
Registered User
 
BT03mach-1's Avatar
 
Join Date: Dec 2003
Location: Friendswood, tx
Posts: 531
Re: MSD Digital Window Switch/Nitrous wiring setup

What is nmu? Nitrous Management unit for zex?
__________________
old 2003 Black Mach-1
Best 12.460 @ 110.15 60' 1.782

new 03 Black Mach-1
BT03mach-1 is offline   Reply With Quote
Old 11-07-2007, 03:29 PM   #31
machgsxr
Registered User
 
machgsxr's Avatar
 
Join Date: Feb 2005
Location: San Antonio
Posts: 6,414
Re: MSD Digital Window Switch/Nitrous wiring setup

Quote:
Originally Posted by BT03mach-1 View Post
What is nmu? Nitrous Management unit for zex?
yup.
machgsxr is offline   Reply With Quote
Old 11-12-2007, 10:27 AM   #32
BT03mach-1
Registered User
 
BT03mach-1's Avatar
 
Join Date: Dec 2003
Location: Friendswood, tx
Posts: 531
Re: wiring diagram for nitrous setup

Quote:
Originally Posted by SheaSanford View Post
Here's a jpg of the wiring diagram i plan to use for my nx efi nitrous system install. If anybody sees anything that seems wrong please let me know. I plan on beginning install tomorrow and will post some pics tomorrow.
Ok i ran everything just like this drawing except i put the wot switch in line with the window switch like the other drawing in this thread (the dry kit) what i don't understand is how if the fuel, window switch and the wot switch are not happy what is going to stop the the noids from not working? it seems like they would still come on.
__________________
old 2003 Black Mach-1
Best 12.460 @ 110.15 60' 1.782

new 03 Black Mach-1
BT03mach-1 is offline   Reply With Quote
Old 11-12-2007, 11:20 AM   #33
BT03mach-1
Registered User
 
BT03mach-1's Avatar
 
Join Date: Dec 2003
Location: Friendswood, tx
Posts: 531
Re: wiring diagram for nitrous setup

Quote:
Originally Posted by Mach1Marauder View Post
If you wired them in series, it takes all of them to activate the 'noids.
so the wire from the relay that goes to the window switch, the fuel pressure switch and wot switch have to be on for the wire from the relay that goes the noids to come on? did that make sense?
__________________
old 2003 Black Mach-1
Best 12.460 @ 110.15 60' 1.782

new 03 Black Mach-1
BT03mach-1 is offline   Reply With Quote
Old 03-26-2008, 08:50 PM   #34
Marlboro_Man
024VGT
 
Marlboro_Man's Avatar
 
Join Date: Feb 2008
Location: League City, Texas
Posts: 68
Re: Installing MSD Digital Window Switch

Quote:
Originally Posted by lxh89 View Post
All of the coil wires lead directly to the ECU. I did this and appears he did too, but we tapped one of these wires on the negative side then configured the Window switch for 1 cylinder mode.

Tony
If I hook the white wire to one of the coil packs, Do I use the common "red" wire , or do I use the other wire which is a differant color for each coil pack?

And

After hooking up the white wire to the coil pack, Do I set up the MSD WS for 1 or 8 cyl mode?

Thanks
__________________
02 GT with 32 valves

http://i31.tinypic.com/14uw2e9.jpg
Marlboro_Man is offline   Reply With Quote
Old 03-27-2008, 11:09 PM   #35
Marlboro_Man
024VGT
 
Marlboro_Man's Avatar
 
Join Date: Feb 2008
Location: League City, Texas
Posts: 68
Re: Installing MSD Digital Window Switch

Quote:
Originally Posted by Marlboro_Man View Post
If I hook the white wire to one of the coil packs, Do I use the common "red" wire , or do I use the other wire which is a differant color for each coil pack?

And

After hooking up the white wire to the coil pack, Do I set up the MSD WS for 1 or 8 cyl mode?

Thanks
I figured it out, You hook the white wire to one of the smaller "colored" wires going to a coil pack.

The red wire that runs to each coil pack is the 12v+ wire. So that would be a nono for the MSD WS.

Also I then set it up for 1 cylender mode.
__________________
02 GT with 32 valves

http://i31.tinypic.com/14uw2e9.jpg
Marlboro_Man is offline   Reply With Quote
Old 06-02-2008, 11:54 PM   #36
Dikki18
Registered User
 
Dikki18's Avatar
 
Join Date: Dec 2007
Location: Tucson, AZ
Posts: 79
Re: MSD Digital Window Switch/Nitrous wiring setup

If anyone is still looking at this? If I'm running one relay for the NMU and MSD Window switch, the yellow wire off the MSD, I can run that to the ground side of the relay? I think that is right, anyone want to correct me or verify? Thanks!
Dikki18 is offline   Reply With Quote
Old 03-03-2009, 08:13 AM   #37
MachSoldier
Registered User
 
MachSoldier's Avatar
 
Join Date: Jan 2008
Location: Fort Bragg, NC
Posts: 170
Re: MSD Digital Window Switch/Nitrous wiring setup

Thank god for this sticky. I just got done wiring up my kit and this was a huge help with all of the diagrams and everything. The only thing I did different is that I used an MSD GMR pickup for the tac signal instead of dealing with pin 12 or whatever it was. No splicing required just hook it up to one of the wires on the coil and you are done. I recommend it. It works great.
__________________
03 DSG Mach 5 spd

Mods: SLP LM1 Catback, Pypes OR X-pipe, K&N drop in, NX 125 Shot, SCT flip chip w/ Custom tune from Competition Auto, M/T ET Streets 275/35/17, H&R SS springs, FRPP Cobra Diff, 31 Spline Moser Axles, 4.10 Gears

Best ET: 11.9 @ 116
MachSoldier is offline   Reply With Quote
Old 07-11-2011, 01:24 AM   #38
bigjohnsonDOHC
Registered User
 
bigjohnsonDOHC's Avatar
 
Join Date: Apr 2008
Location: Auburn, MA
Posts: 315
Re: MSD Digital Window Switch/Nitrous wiring setup

Im assuming the coil wire you guys are splicing into is for the rpm wire right? Anyone happen to have a picture of what wire was spliced into? This is the last thing needed for my install.
__________________
2003 Black Mach 1
-SLP LM1, KN intake, subframe connectors, UPR x-pipe w/ high flow cats
bigjohnsonDOHC is offline   Reply With Quote
Old 07-12-2011, 12:32 AM   #39
01snake
Registered User
 
Join Date: Jul 2008
Location: macomb, MI
Posts: 238
Re: MSD Digital Window Switch/Nitrous wiring setup

Quote:
Originally Posted by MachSoldier View Post
Thank god for this sticky. I just got done wiring up my kit and this was a huge help with all of the diagrams and everything. The only thing I did different is that I used an MSD GMR pickup for the tac signal instead of dealing with pin 12 or whatever it was. No splicing required just hook it up to one of the wires on the coil and you are done. I recommend it. It works great.

do you have the msd digital window switch?

so you just used that MSD GMR and didnt need a tach adapter?

i am having a problem with mine it reads fine up to 4k rpms and then goes to 0. i think i may need a tach adpater or this?
__________________
2001 cobra

full bolt on's, nx wet kit.......you get the point
01snake is offline   Reply With Quote
Old 07-31-2013, 02:21 PM   #40
Explosive
Registered User
 
Explosive's Avatar
 
Join Date: Jul 2010
Location: Michigan
Posts: 876
Re: MSD Digital Window Switch/Nitrous wiring setup

So what's the deal? Nx tells me with their window switch I need a tach adapter. Do you not need one with the msd switch? I'm having second thoughts on the nx switch the msd ones looks a bit nicer
Explosive is offline   Reply With Quote
Old 08-28-2013, 06:20 PM   #41
mach18604
Registered User
 
mach18604's Avatar
 
Join Date: Nov 2005
Location: Lyndhurst, Ohio
Posts: 2,287
Re: MSD Digital Window Switch/Nitrous wiring setup

Lots of wiring !

Im looking to get a kit... just reading up on all this stuff!
__________________
Collecting for an Eaton Swap down the road..
mach18604 is offline   Reply With Quote
Old 09-03-2013, 03:04 AM   #42
two-gun
Registered User
 
Join Date: Aug 2011
Location: Hayward,Ca
Posts: 134
Re: MSD Digital Window Switch/Nitrous wiring setup

Anyone here use a WOT Box ?
two-gun is offline   Reply With Quote
Old 08-02-2015, 06:30 PM   #43
03mach1ne
Registered User
 
Join Date: Jun 2014
Location: birmingham, alabama
Posts: 11
Re: MSD Digital Window Switch/Nitrous wiring setup

i know this is a really old post but it says the white wire goes to ecu pin #26. Where exactly can i find this edu pin #26
03mach1ne is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:47 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<