WTB Shaker spacer/riser and procharger plastic shaker diverter thingy - 2003-04 Mach 1 Registry Owners Club

FenixFallen · 05-21-2019, 08:55 PM

Hello, I'm looking for a shaker spacer/riser, not to be confused with the intake plenum spacer (already have that). Not sure if anyone still makes them anymore.

I am also looking for the plastic piece that comes with the procharger kit for the Mach 1 that attaches to the shaker and diverts the air over near the filter. Here is a picture of the piece I'm talking about installed:

Any help would be appreciated in locating these pieces, thanks!

Mach1azure · 05-23-2019, 04:48 PM

Quote:

Originally Posted by FenixFallen

Hello, I'm looking for a shaker spacer/riser, not to be confused with the intake plenum spacer (already have that). Not sure if anyone still makes them anymore.

I am also looking for the plastic piece that comes with the procharger kit for the Mach 1 that attaches to the shaker and diverts the air over near the filter. Here is a picture of the piece I'm talking about installed:

Any help would be appreciated in locating these pieces, thanks!

Funny, I posted the same thing on the Facebook page. No one makes them. You would have to have one custom made

FenixFallen · 05-23-2019, 07:54 PM

It looks like CDC makes a 3/8" riser, which is a little shorter than I was hoping for but it might do the job.

My crazy plan involves cutting/drilling slots or holes in the back of the spacer, and drilling holes in the lower shaker piece to turn the shaker into a heat exchanger. I have the shaker air diverter, which basically made the back half of the shaker useless, and once I installed the procharger the front half of the shaker lost most of its functionality as well, outside of just pulling cooler air into the engine bay. so I figure with a spacer I wouldn't have to destroy my shaker for an experiment. with the lower shaker if it doesn't work out I can always plug the holes.

Mattstang04 · 05-23-2019, 10:47 PM

PM sent.

Mattstang04 · 05-24-2019, 11:58 AM

3/4"

blieknight · 06-24-2019, 02:57 AM

Quote:

Originally Posted by Mattstang04

3/4"

Where can I get one of those.

05-21-2019, 08:55 PM	#1
FenixFallen Newb Join Date: Nov 2011 Location: Barre, Vermont Posts: 206	WTB Shaker spacer/riser and procharger plastic shaker diverter thingy Hello, I'm looking for a shaker spacer/riser, not to be confused with the intake plenum spacer (already have that). Not sure if anyone still makes them anymore. I am also looking for the plastic piece that comes with the procharger kit for the Mach 1 that attaches to the shaker and diverts the air over near the filter. Here is a picture of the piece I'm talking about installed: Any help would be appreciated in locating these pieces, thanks! __________________ Black 2003 Mach 1, 483hp/451tq @6100 8.9psi -Stock longblock, stock transmission, Procharger D1SC 4.15" pulley, Accufab 60mm TB, P/P intake manifold, full MAC exhaust, return style fuel system, Maximum Motorsports/Steeda suspension, Torsen T2R 31 spline diff Red 2007 Focus ST, daily driver, 236hp/234tq @10psi -FSWerks gt2871r kit, Cosworth intake manifold, FSWerks Stealth exhaust, FRPP lowering springs

05-23-2019, 07:54 PM	#3
FenixFallen Newb Join Date: Nov 2011 Location: Barre, Vermont Posts: 206	Re: WTB Shaker spacer/riser and procharger plastic shaker diverter thingy It looks like CDC makes a 3/8" riser, which is a little shorter than I was hoping for but it might do the job. My crazy plan involves cutting/drilling slots or holes in the back of the spacer, and drilling holes in the lower shaker piece to turn the shaker into a heat exchanger. I have the shaker air diverter, which basically made the back half of the shaker useless, and once I installed the procharger the front half of the shaker lost most of its functionality as well, outside of just pulling cooler air into the engine bay. so I figure with a spacer I wouldn't have to destroy my shaker for an experiment. with the lower shaker if it doesn't work out I can always plug the holes. __________________ Black 2003 Mach 1, 483hp/451tq @6100 8.9psi -Stock longblock, stock transmission, Procharger D1SC 4.15" pulley, Accufab 60mm TB, P/P intake manifold, full MAC exhaust, return style fuel system, Maximum Motorsports/Steeda suspension, Torsen T2R 31 spline diff Red 2007 Focus ST, daily driver, 236hp/234tq @10psi -FSWerks gt2871r kit, Cosworth intake manifold, FSWerks Stealth exhaust, FRPP lowering springs

05-23-2019, 10:47 PM	#4
Mattstang04 Registered User Join Date: May 2017 Location: St. Louis, MO Posts: 28	Re: WTB Shaker spacer/riser and procharger plastic shaker diverter thingy PM sent.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)