Eaton Swap.....

[SHAKN' 04]

Originally Posted by WNTAMACH1

Ya Ya, Build the engine and throw a 3.4 Whipple on top

nah, eaton will do just fine. cammed/eaton swap ftw

[machgsxr]

Originally Posted by machgsxr

ATTT: DANIEL


2r3z6312baa - Crank pulley /Harmonic Balancer
f1az6378a - washer for balancer - $3.68
f5rz6a340b - bolt for balancer - $6.04
2r3z10153ca - Bracket that replaces stk. alt. on 99-01 Cobra’s and 03/04 Mach 1’s (Comes w/ pulley below if bought used) - $58.86
yw7z8678aa - pulley for above bracket
2r3z6b209bc - Pulley bridge assembly for S.C. (If bought new it comes with the bridge, 2 idlers and tensioner) - $285.80
(8678B) Idler pulley,timing cover pass. side
yw7z8678aa - pulley on drivers side of timing cover
(6D080) Timing cover (if bought new, it comes w/ pulley on drivers side and tensioner)
s5az6700a - timing cover seal
(10A313) Upper alternator bracket
(10153) Lower alternator bracket
(10346) Alternator
1U2Z-14S411-TA Electrical connector (alt. to harmness )
(6B209A) Tensioner on timing cover
2r3z8260ab - Radiator hose - $18.98
2r3z8a593ab - Radiator hose - $24.10
2r3z8k576aa - Radiator hose - $15.18
2r3z8548aa - Water cross over pipe - $75.72
(6881) Cobra oil cooler adapter
(6A642) Cobra Oil cooler
2r3z9002aa - Cobra fuel tank (optional)
2r3z9h307ab - Cobra fuel pump (optional)
2r3z9424bb - Lower intake
(6K775) Garrett factory intercooler
3U2Z-14S411-SSA IAT2 sensor connector
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c) - $92.62 says it is discontinued might call and verify or see if they changed part #'s.
3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res. - $19.62
2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block - $10.88
2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new) - $11.89
2r3z9l443da - Intercooler line that goes from hard line to hard line - $16.84
f8yz8501aa - Ford / Bosche water pump for intercooler - $175.99
2r3z8n500ac - Intercooler pump bracket - $59.76
2r3z8a193aa - Heat exchanger mounting bracket - $204.75
2r3z8c386aa - 2each bracket clamps for h/e - $20.91
(9N491B) Lower manifold to intercooler water adapter
(9B659) Intake tube from maf to t/b.
(9F715) IAC valve
2r3z9a825aa - Cruise control cable - $20.71
2r3z9a758aa - Throttle cable - $31.98
(6C324) PCV tubing
(9F479) Sensor on the back of the S/C
2r3z6020aa - Timing cover gasket LH side - $8.37
2r3z6020ba -Timing cover gasket middle - $10.99
2r3z6020ca - Timing cover gasket RH side - $8.10
2r3z9h486aa - Lower intake to S.C. gasket - $14.29
2r3z9l437bb - Plenum to S/C gasket - $9.72
2r3z3490aa - Power steering resevoir bracket. - $196.86
i/c pigtail
Inner acc 6 rib belt
n80478s309 - (4) coolant crossover and pulley bridge can be picked up at local auto parts store in help section.
n805164437 - (1) Bolt for pulley cage to timing cover. - $3.85
n808102s437 - bolt that is used on the idlers and pulleys. Only need if you buy parts seperately. You will need a total of at least 6 of these. - $3.30
n808920s437 - Pulley bridge bolts - $2.20
n606677-s36 (4) Bolts to bolt the bracket clamps to the h/e bracket - $0.55
N605909s437 - (4) bolts for the upper alt. bracket - $1.10
n807274s437 (1) lower alt. bracket to alt bolt- $0.55

Got as much pricing as I could. Ill text you tomorrow.

[ASMACH]

Anyone running 4.10's with a built motor and a 2.76 pulley? Im wondering if ill just be spinning all day on the street.

[SHAKN' 04]

Originally Posted by machgsxr

Got as much pricing as I could. Ill text you tomorrow.

thank you sir!

[machgsxr]

Originally Posted by ASMACH

Anyone running 4.10's with a built motor and a 2.76 pulley? Im wondering if ill just be spinning all day on the street.

With street tires yes. With drag radials a little. You will need to learn how to drive so you don't spin.

[SHAKN' 04]

Archie, gonna update this thing in the morning! should be a few more purchases left to complete this kit!!

[SHAKN' 04]

---------Updated-------- Archie: im sure there are going to be more parts coming off this list in the next week when i finish swapping parts with the turbo cobra guy. I might have even missed a few parts, just need to lay it all out again next week and go thru this again.

2r3z10153ca - Bracket that replaces stk. alt. on 99-01 Cobra’s and 03/04 Mach 1’s (Comes w/ pulley below if bought used) - $58.86
yw7z8678aa - pulley for above bracket
(8678B) Idler pulley,timing cover pass. side
yw7z8678aa - pulley on drivers side of timing cover
s5az6700a - timing cover seal
(10A313) Upper alternator bracket ----traded
(10153) Lower alternator bracket ----traded
(10346) Alternator----traded
1U2Z-14S411-TA Electrical connector (alt. to harmness )
2r3z8260ab - Radiator hose - $18.98
2r3z8a593ab - Radiator hose - $24.10
2r3z8k576aa - Radiator hose - $15.18
(6881) Cobra oil cooler adapter
(6A642) Cobra Oil cooler
U2Z-14S411-SSA IAT2 sensor connector
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c) - $92.62 says it is discontinued might call and verify or see if they changed part #'s.
3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res. - $19.62
2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block - $10.88
2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new) - $11.89
2r3z9l443da - Intercooler line that goes from hard line to hard line - $16.84
f8yz8501aa - Ford / Bosche water pump for intercooler - $175.99
2r3z8n500ac - Intercooler pump bracket - $59.76
2r3z8a193aa - Heat exchanger mounting bracket - $204.75
2r3z8c386aa - 2each bracket clamps for h/e - $20.91
(9N491B) Lower manifold to intercooler water adapter
(9F715) IAC valve
2r3z9a825aa - Cruise control cable - $20.71 ---traded
2r3z9a758aa - Throttle cable - $31.98 ---traded
(6C324) PCV tubing
(9F479) Sensor on the back of the S/C
2r3z6020aa - Timing cover gasket LH side - $8.37
2r3z6020ba -Timing cover gasket middle - $10.99
2r3z6020ca - Timing cover gasket RH side - $8.10
2r3z9h486aa - Lower intake to S.C. gasket - $14.29
2r3z9l437bb - Plenum to S/C gasket - $9.72
2r3z3490aa - Power steering resevoir bracket. - $196.86
i/c pigtail
Inner acc 6 rib belt
n80478s309 - (4) coolant crossover and pulley bridge can be picked up at local auto parts store in help section.
n805164437 - (1) Bolt for pulley cage to timing cover. - $3.85
n808102s437 - bolt that is used on the idlers and pulleys. Only need if you buy parts seperately. You will need a total of at least 6 of these. - $3.30
n808920s437 - Pulley bridge bolts - $2.20
n606677-s36 (4) Bolts to bolt the bracket clamps to the h/e bracket - $0.55
N605909s437 - (4) bolts for the upper alt. bracket - $1.10
n807274s437 (1) lower alt. bracket to alt bolt- $0.55

[machgsxr]

Originally Posted by machgsxr

ATTT: DANIEL

f1az6378a - washer for balancer
f5rz6a340b - bolt for balancer
2r3z10153ca - Bracket that replaces stk. alt. on 99-01 Cobra’s and 03/04 Mach 1’s (Comes w/ pulley below if bought used)
yw7z8678aa - pulley for above bracket
2r3z8260ab - Radiator hose
2r3z8a593ab - Radiator hose
2r3z8k576aa - Radiator hose
2r3z8548aa - Water cross over pipe
(6881) Cobra oil cooler adapter
(6A642) Cobra Oil cooler
2r3z9002aa - Cobra fuel tank (optional)
2r3z9h307ab - Cobra fuel pump (optional)
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c)
3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res.
2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block
2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new)
2r3z9l443da - Intercooler line that goes from hard line to hard line
f8yz8501aa - Ford / Bosche water pump for intercooler
2r3z8n500ac - Intercooler pump
2r3z8a193aa - Heat exchanger mounting bracket
2r3z8c386aa - 2each bracket clamps for h/e
(9B659) Intake tube from maf to t/b
2r3z6020aa - Timing cover gasket LH side
2r3z6020ba -Timing cover gasket middle
2r3z6020ca - Timing cover gasket RH side
2r3z9h486aa - Lower intake to S.C. gasket
2r3z9l437bb - Plenum to S/C gasket
i/c pigtail
Inner acc 6 rib belt
n80478s309 - (4) coolant crossover and pulley bridge can be picked up at local auto parts store in help section.
n805164437 - (1) Bolt for pulley cage to timing cover.
n808102s437 - bolt that is used on the idlers and pulleys. Only need if you buy parts seperately. You will need a total of at least 6 of these.
n808920s437 - Pulley bridge bolts
n606677-s36 (4) Bolts to bolt the bracket clamps to the h/e bracket
N605909s437 - (4) bolts for the upper alt. bracket
n807274s437 (1) lower alt. bracket to alt bolt

Your updated list from parts that I know you have purchased. I think it's pretty accurate. I would really have to see all the parts after you get them in to check off anything else that they might have sent with them.

[SHAKN' 04]

kool archie thanks, ill be getting more parts next week, once they get here, ill lay them out and send u pics

[mustangfrank]

http://www.americanmuscle.com/frpp-a...ory-drive.html

Is that all the piece you need for an eaton swap? injector and supercharger are missing.

[SHAKN' 04]

Originally Posted by mustangfrank

http://www.americanmuscle.com/frpp-a...ory-drive.html

Is that all the piece you need for an eaton swap? injector and supercharger are missing.

not even close, there's way more parts you'll need.

[mustangfrank]

okay

[SHAKN' 04]

Atten Archie: i took off a few parts that came in the other day, looks like theres just odds and ends stuff to get. If you have any info on whats left, txt me so i can post a final list on what i need. thanks man

2r3z10153ca - Bracket that replaces stk. alt. on 99-01 Cobra’s and 03/04 Mach 1’s (Comes w/ pulley below if bought used)
yw7z8678aa - pulley for above bracket
2r3z8260ab - Radiator hose
2r3z8a593ab - Radiator hose
2r3z8k576aa - Radiator hose
(6881) Cobra oil cooler adapter
(6A642) Cobra Oil cooler
2r3z9h307ab - Cobra fuel pump (optional)---(gettin from tomas)
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c)
3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res.
2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block
2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new)
2r3z9l443da - Intercooler line that goes from hard line to hard line
2r3z8a193aa - Heat exchanger mounting bracket
2r3z8c386aa - 2each bracket clamps for h/e
(9B659) Intake tube from maf to t/b
2r3z6020aa - Timing cover gasket LH side
2r3z6020ba -Timing cover gasket middle
2r3z6020ca - Timing cover gasket RH side
2r3z9h486aa - Lower intake to S.C. gasket
2r3z9l437bb - Plenum to S/C gasket
i/c pigtail
Inner acc 6 rib belt
n80478s309 - (4) coolant crossover and pulley bridge can be picked up at local auto parts store in help section.
n805164437 - (1) Bolt for pulley cage to timing cover.
n808102s437 - bolt that is used on the idlers and pulleys. Only need if you buy parts seperately. You will need a total of at least 6 of these.
n808920s437 - Pulley bridge bolts
n606677-s36 (4) Bolts to bolt the bracket clamps to the h/e bracket
N605909s437 - (4) bolts for the upper alt. bracket
n807274s437 (1) lower alt. bracket to alt bolt

[machgsxr]

These are the parts you need to finish it up. Like i told you, we could try and make those hard lines out of just heater hose if you want to. Save you some money.


gasket for i/c adapter to lower intake - One I sent a picture of.

f5rz6a340b - bolt for balancer - $6.04

2r3z8260ab - Radiator hose - $18.98

2r3z8a593ab - Radiator hose - $24.10

2r3z8k576aa - Radiator hose - $15.18

2r3z6020aa - Timing cover gasket LH side - $8.37

2r3z6020ba -Timing cover gasket middle - $10.99

2r3z6020ca - Timing cover gasket RH side - $8.10

2r3z9h486aa - Lower intake to S.C. gasket - $14.29

i/c pigtail

Inner acc 6 rib belt

I would just get all the parts above new from Ford unless they have them cheaper at the local parts store.
------------------------------------
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c) - $92.62 says it is discontinued might call and verify or see if they changed part #'s.

2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block - $10.88

2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new) - $11.89

s5az6700a - timing cover seal

(10A313) Upper alternator bracket
------------------------------------
Parts below are what you need to drop off next time you swing by.

EGR Delete kit
h/e, mounting brackets and clamps
p/s resevoir bracket
oil cooler and adapter setup
bracket and idler

[SHAKN' 04]

Originally Posted by machgsxr

These are the parts you need to finish it up. Like i told you, we could try and make those hard lines out of just heater hose if you want to. Save you some money.


gasket for i/c adapter to lower intake - One I sent a picture of.

f5rz6a340b - bolt for balancer - $6.04

2r3z8260ab - Radiator hose - $18.98

2r3z8a593ab - Radiator hose - $24.10

2r3z8k576aa - Radiator hose - $15.18

2r3z6020aa - Timing cover gasket LH side - $8.37

2r3z6020ba -Timing cover gasket middle - $10.99

2r3z6020ca - Timing cover gasket RH side - $8.10

2r3z9h486aa - Lower intake to S.C. gasket - $14.29

i/c pigtail

Inner acc 6 rib belt

I would just get all the parts above new from Ford unless they have them cheaper at the local parts store.
------------------------------------
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c) - $92.62 says it is discontinued might call and verify or see if they changed part #'s.

2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block - $10.88

2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new) - $11.89

s5az6700a - timing cover seal

(10A313) Upper alternator bracket
------------------------------------
Parts below are what you need to drop off next time you swing by.

EGR Delete kit
h/e, mounting brackets and clamps
p/s resevoir bracket
oil cooler and adapter setup
bracket and idler

will do!! Archie ur the man! still want to hire me?? haha

[SHAKN' 04]

[QUOTE=machgsxr;1456500]


-2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c) - $92.62 says it is discontinued might call and verify or see if they changed part #'s.

-2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block - $10.88

-(10A313) Upper alternator bracket
------------------------------------

This is whats left to get for my swap!

[machgsxr]

[QUOTE=SHAKN' 04;1456822]

Originally Posted by machgsxr

-gasket for i/c adapter to lower intake - One I sent a picture of.

-2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c) - $92.62 says it is discontinued might call and verify or see if they changed part #'s.

-2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block - $10.88

-(10A313) Upper alternator bracket
------------------------------------

This is whats left to get for my swap!

Like I said to you in that text, I can make those lines out of just heater hose. Be allot cheaper. What about that guy you swapped some parts with. Check with him to see if he has them. He does not need them at all.

[SHAKN' 04]

[QUOTE=machgsxr;1456830]

Originally Posted by SHAKN' 04

Like I said to you in that text, I can make those lines out of just heater hose. Be allot cheaper. What about that guy you swapped some parts with. Check with him to see if he has them. He does not need them at all.

ok, if we have to make them, we will. ill txt him right now. also got the gasket for i/c adapter to lower intake.

[Cobra Drifter]

Where did you guys get the pricing for the parts from? Sorry I couldnt read all 23 pages lol.

I just ordered two of the intercooler hoese and one was right on but the other you have is like 1/2 of what I paid

3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res. - $19.62
2r3z9l443ba - $10 but mine was $21 (trying to see if they will cut me more of a discount)

Sup Archie, know you from SVTP and bought parts from you over there. My swap in almost done. Next week I should have all my missing hoses and vaccuum caps so it will be ready to start up for the first time in 13 months

[SHAKN' 04]

Originally Posted by Cobra Drifter

Where did you guys get the pricing for the parts from? Sorry I couldnt read all 23 pages lol.

I just ordered two of the intercooler hoese and one was right on but the other you have is like 1/2 of what I paid

3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res. - $19.62
2r3z9l443ba - $10 but mine was $21 (trying to see if they will cut me more of a discount)

Sup Archie, know you from SVTP and bought parts from you over there. My swap in almost done. Next week I should have all my missing hoses and vaccuum caps so it will be ready to start up for the first time in 13 months

Tousley from SVTP, i delt with Scott i believe.

[SergeantZ]

So if one were to use this bracket (http://www.svtperformance.com/forums...-brackets.html), what all would that replace as far as parts and swap steps? Anyone else use one of these?

[agentorangeCH]

Hi Guys

I have a 2001 Cobra and want to do also an eaton swap. I've almost everything that I need, also parts that acutally arent needed after I read this thread here, like the complete ecu with harness...

The biggest part which is still dont have, is the fuel tank with pumps. But I will buy one from ebay, I think. There some other parts like new gaskets, which I have to buy. I bought a set for about 3.6k but with a Stiegemeier Stage 4 ported eaton, metco lower pulley kit and LFP Heat exchanger.

But I have some questions. The 01 Cobra has the same IAC like the Mach1? So I have to buy a new one? What about the IAT2 Baro sensor? Do I have to change that one too? Something that is also not clear for me, is thing about the knock sensor. Has the 01 Cobra also this knock sensor? Didnt found something in the I-Net.

Would be thankful for some help.

[Kove]

Originally Posted by agentorangeCH

Hi Guys

I have a 2001 Cobra and want to do also an eaton swap. I've almost everything that I need, also parts that acutally arent needed after I read this thread here, like the complete ecu with harness...

The biggest part which is still dont have, is the fuel tank with pumps. But I will buy one from ebay, I think. There some other parts like new gaskets, which I have to buy. I bought a set for about 3.6k but with a Stiegemeier Stage 4 ported eaton, metco lower pulley kit and LFP Heat exchanger.

But I have some questions. The 01 Cobra has the same IAC like the Mach1? So I have to buy a new one? What about the IAT2 Baro sensor? Do I have to change that one too? Something that is also not clear for me, is thing about the knock sensor. Has the 01 Cobra also this knock sensor? Didnt found something in the I-Net.

Would be thankful for some help.

You don't have to get the Cobra IAC but it is recommended because of the way our stock ones wiring harness points to the hood instead of to the side. For the IAT2, you can use either the IAT sensor in the intake or the IAT2 at the back of the blower. Our wiring harness doesn't have the provisions for both.


Sent from my iPhone using Tapatalk

[machgsxr]

Originally Posted by Kove

You don't have to get the Cobra IAC but it is recommended because of the way our stock ones wiring harness points to the hood instead of to the side. For the IAT2, you can use either the IAT sensor in the intake or the IAT2 at the back of the blower. Our wiring harness doesn't have the provisions for both.


Sent from my iPhone using Tapatalk

Since you have an 01, I think they have a separate iat sensor already. You can use that one or just extend the wires to the iat2, which would be preferred for most. If you use the stock one you will still need the iat2 sensor to plug the hole in the blower.

For iac you can user the stock one, but you will have to put it in a vice and turn it 90 degrees so that it points to the side.

Yes, the 01s still have the knock sensors in the valley.

[agentorangeCH]

Thank you for the answers.


That would be my next question, if I can turn the IAC sensor to the side. But thats some more, that I dont have to buy.

That means I can use the IAT at the intake tube or extend the wires to the IAT2 behind the blower? So I actually dont need the IAT at the intake?

About the knock sensors, so I have to grind them or?

I'm not sure, if I should do the swap by myself or bring it to the car shop. They want about 2500Euro incl. DynoTune. How complicated is to do the swap? I'm not a mechanic, but its not so that I'm a complete noob. I replaced many things by myself like the complate intake manifold, radiator, CAI. But a eaton swap I a level higher I think.

thanks for your help