2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Power Adders

Power Adders Superchargers, Turbos, Nitrous, etc...

Reply
 
Thread Tools Display Modes
Old 10-13-2011, 02:59 AM   #1
ASH302
Soldier for Christ
 
ASH302's Avatar
 
Join Date: May 2009
Location: Willis, TX at The Daddy ASh Ranch
Posts: 30,596
Official Vortech HP/TQ/mods thread

i see we have a sticky for all other power adders and i know there are a few members that run Vortech on there Mach's. so i figure it be a good thing if they put there info down like in the other ones, to help guys at, i just copy and paste the format from the procharger thread, also please make this a sticky

Please use the following format.

Stock bottom end:

Head unit:

Pulley size and boost level:

Fuel system:

Tuner/Dyno shop info:

Other notable mods:

RWHP/RWTQ:

ASh
__________________
2001 lazer red v6 Mustang coupe sold in Aug 2006
2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012
2013 grey 6 speed coupe GT Mustang Sold in Feb 2014
2013 RED Dodge Charger R/T Sold Nov 2014
2002 custom Blue 02 Auto Trans AM Sold June 2015
1998 Cobra Black Sold summer 2016

Current
2009 Ford F350 FX4 March 2017 (work truck)
2003 OW 5.0 Mach 1 Aug 2020

ASh
ASH302 is offline   Reply With Quote
Old 10-15-2011, 12:39 PM   #2
Chances50
Registered User
 
Join Date: Jun 2008
Location: Haskell, Ok
Posts: 1,325
Re: Official Vortech HP/TQ/mods thread

Stock bottom end: no forged 10.2 compression

Head unit: V2 SC

Pulley size and boost level: 3.12 9psi

Fuel system: return style stealth 340 pumps and 80lb injectors

Tuner/Dyno shop info: Travis Franklin at Gearheads Performance

Other notable mods: Intercooler, power pipe, full exhaust

RWHP/RWTQ: 536rwhp 444rwtq on e85 23* timing, 8 psi 464rwhp 402rwtq on 91 12* timing

Last edited by Chances50; 09-21-2012 at 01:46 AM.
Chances50 is offline   Reply With Quote
Old 10-16-2011, 02:50 AM   #3
cruzmach1
cruzmach1
 
cruzmach1's Avatar
 
Join Date: Sep 2009
Location: Bronx NY
Posts: 801
Re: Official Vortech HP/TQ/mods thread

Stock bottom end: Yes

Head unit: V2 S-Trim

Pulley size and boost level: 3.48 with 10lbs of boost

Fuel system: 39lb Cobra injectors and Focus fuel pump w/Kenne Bell BAP (20amp)

Tuner/Dyno shop info: Mustang Magic

Other notable mods: Intercooler, PHP 3/8 Intake Spacer, Bassani Catted X-Pipe, Borla Stinger Cat Back.

RWHP/RWTQ: 455RWHP & 396RWTQ
__________________
2004 Mustang mach 1 (5-Speed)
Vortech V-2 with intercooler 455RWHP & 396RWTQ
Mustang Magic Tune
3/8 PHP Intake Spacer
Mac 5/8 Long Tube Headers
Mac Catted H-Pipe
Magnaflow Cat Back
Steeda Short throw shifter
cruzmach1 is offline   Reply With Quote
Old 10-17-2011, 04:09 AM   #4
hecdel40
Registered User
 
Join Date: May 2008
Location: Waveland MS
Posts: 326
Re: Official Vortech HP/TQ/mods thread

Bottom end: Build over at Modular Performance 9.5.1 compression.

Head Unit: V2 SQ-Trim with aftercooler.

Pulley size: 3.25

Fuel System: Return style system with two walbro 255 pumps and 80lb injectors

Tuner: Matt from MMP.

Other notable mods: 98 cobra intake cams and a few other things.

RWHP/RWTQ: The car made 551 rwhp and 512 rwtq at only 10 psi of boost and +10 on the timing at only 5900 RPMs.

Note: When I get back to the states in Feb going to put a T-Trim head unit and up the timing and see what happens.
hecdel40 is offline   Reply With Quote
Old 10-26-2011, 09:52 PM   #5
Rumplemenz
Registered User
 
Rumplemenz's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 553
Re: Official Vortech HP/TQ/mods thread

Stock bottom end: Yes

Head unit: V2 sq-trim with aftercooler

Pulley size and boost level: 3.48" 9.1 lbs

Fuel system: 255 svt focus pump, 42 lb frpp injectors

Tuner/Dyno shop info: Dan Carlson (owner) Realspeed Automotive, Bohemia, NY

Other notable mods: Anderson Powerpipe, 90mm maf, frpp 4.10's

RWHP/RWTQ: 455/389
Rumplemenz is offline   Reply With Quote
Old 01-30-2012, 04:31 PM   #6
GR8 WYT
Registered User
 
Join Date: Aug 2002
Location: Hughesville, Maryland
Posts: 594
Re: Official Vortech HP/TQ/mods thread

Stock bottom end: No, Aluminator NA short block 10.1 compression.

Head unit: V2 (Upgraded impellor to SI spec)

Pulley size and boost level: Stock, boost unknown (10-sih?)

Fuel system: Cobra tank and fuel pumps, BAP, 60lb injectors

Tuner/Dyno shop info: JPC Racing

Other notable mods: Intercooler, PHP 3/8 Intake Spacer, Bassani ceramic coated mid lenght headers, Bassani Catted X-Pipe, Dynomax cat back

RWHP/RWTQ: 514 RWHP 462 RWTQ
__________________
Aluminator NA bottom end, rebuilt stock heads, Vortech V2, 3.90 gear, 514 RWHP, 468 RWTQ. Motor and tune by JPC. (Millersville, MD)
GR8 WYT is offline   Reply With Quote
Old 01-30-2012, 05:33 PM   #7
rcodemach1
Registered User
 
rcodemach1's Avatar
 
Join Date: Jan 2004
Location: san diego, ca
Posts: 1,461
Re: Official Vortech HP/TQ/mods thread

Nice results for sure.

Is that the Vortech pulley that normally comes with the intercooled kit? I believe those are 3.48". That SI wheel seems to be a nice upgrade from an SC.

What all did the heads need? Any guide work or milling?

Lastly is that on stock cams and are the cams degreed or dot-to-dot?

Quote:
Originally Posted by GR8 WYT View Post
Stock bottom end: No, Aluminator NA short block 10.1 compression.

Head unit: V2 (Upgraded impellor to SI spec)

Pulley size and boost level: Stock, boost unknown (10-sih?)

Fuel system: Cobra tank and fuel pumps, BAP, 60lb injectors

Tuner/Dyno shop info: JPC Racing

Other notable mods: Intercooler, PHP 3/8 Intake Spacer, Bassani ceramic coated mid lenght headers, Bassani Catted X-Pipe, Dynomax cat back

RWHP/RWTQ: 514 RWHP 462 RWTQ
__________________

'03 Mach, Oxford White, 5-spd, Eaton
'03 Mach, Black, automatic (parting out)
'98 GT, 410w, C4, Vortech

rcodemach1 is offline   Reply With Quote
Old 02-06-2012, 04:34 PM   #8
GR8 WYT
Registered User
 
Join Date: Aug 2002
Location: Hughesville, Maryland
Posts: 594
Re: Official Vortech HP/TQ/mods thread

Is that the Vortech pulley that normally comes with the intercooled kit? (YES) I believe those are 3.48". That SI wheel seems to be a nice upgrade from an SC.

What all did the heads need? Any guide work or milling? (Complete rebuild...so they are cam ready when I'm ready)

Lastly is that on stock cams and are the cams degreed or dot-to-dot? (Stock...no idea on the other questions)
__________________
Aluminator NA bottom end, rebuilt stock heads, Vortech V2, 3.90 gear, 514 RWHP, 468 RWTQ. Motor and tune by JPC. (Millersville, MD)
GR8 WYT is offline   Reply With Quote
Old 02-06-2012, 04:50 PM   #9
rcodemach1
Registered User
 
rcodemach1's Avatar
 
Join Date: Jan 2004
Location: san diego, ca
Posts: 1,461
Re: Official Vortech HP/TQ/mods thread

Then those are impressive numbers for that pulley and overall combo.

__________________

'03 Mach, Oxford White, 5-spd, Eaton
'03 Mach, Black, automatic (parting out)
'98 GT, 410w, C4, Vortech

rcodemach1 is offline   Reply With Quote
Old 02-19-2012, 04:16 AM   #10
hecdel40
Registered User
 
Join Date: May 2008
Location: Waveland MS
Posts: 326
Re: Official Vortech HP/TQ/mods thread

Quote:
Originally Posted by rcodemach1 View Post
Then those are impressive numbers for that pulley and overall combo.

I think that sound about right with his combo.
hecdel40 is offline   Reply With Quote
Old 02-19-2012, 09:49 AM   #11
rcodemach1
Registered User
 
rcodemach1's Avatar
 
Join Date: Jan 2004
Location: san diego, ca
Posts: 1,461
Re: Official Vortech HP/TQ/mods thread

On an SC with a 3.6" pulley and headers, about 440-450 rwhp seems to be common.

With an S-trim and a 3.48", maybe 470 (My previous non-IC setup).

So 514 rwhp with stock cams and 3.48" pulley is really good.

The difference must be the SI upgrade. I think I want one.
__________________

'03 Mach, Oxford White, 5-spd, Eaton
'03 Mach, Black, automatic (parting out)
'98 GT, 410w, C4, Vortech

rcodemach1 is offline   Reply With Quote
Old 04-08-2012, 08:37 PM   #12
need it
Registered User
 
need it's Avatar
 
Join Date: Aug 2006
Location: longisland, n.y
Posts: 615
Re: Official Vortech HP/TQ/mods thread

vortech e -trim numbers in sig
__________________
2004 dsg mach1
vortech v2 e trim
paxton air to air intercooler
cobra mass air #39 injectors
cobra tank,gt pumps,vortech bov
373 gears
steeda tri-axe shifter
magnaflow catted x sss systems catback
brembo drilled and slotted rotors,hawk pads
eibach prokit, tokico shocks and struts
fr500 wheels 18x9 18x10.5
m&m full length subframe connectors
alluminum driveshaft
2003 cobra mirrors,and sideskirts
steeda front swaybar
2001 cobra front bumper
432 rwhp 385 rtq at 8 psi
need it is offline   Reply With Quote
Old 04-14-2012, 06:31 PM   #13
Chances50
Registered User
 
Join Date: Jun 2008
Location: Haskell, Ok
Posts: 1,325
Re: Official Vortech HP/TQ/mods thread

Quote:
Originally Posted by rcodemach1 View Post
On an SC with a 3.6" pulley and headers, about 440-450 rwhp seems to be common.

With an S-trim and a 3.48", maybe 470 (My previous non-IC setup).

So 514 rwhp with stock cams and 3.48" pulley is really good.

The difference must be the SI upgrade. I think I want one.
The SI upgrade is worth a few lbs over the s/sc with the same pulley.
__________________
03 OW 5 speed 84k miles very clean. For sale!
Chances50 is offline   Reply With Quote
Old 06-13-2012, 10:46 PM   #14
GR8 WYT
Registered User
 
Join Date: Aug 2002
Location: Hughesville, Maryland
Posts: 594
Re: Official Vortech HP/TQ/mods thread

Here's a list of the most recent mods to get the 514 RWHP. On top of this, I already had the Cobra tank, dual pumps, Boost a Pump. In retrospec...I should have sprung for a return style fuel setup. The Vortech upgrade plus keeping 10:1 compression with the NA shortblock helped.

ALUMINATOR 4.6L FORGED N/A Shortblock
Shipping and Handling
Rebuild cyl heads w/new vlaves and springs---est
60lb High Impedence Fuel Injectors (SET)
Oil Pump, High-Volume, Ford, 4.6L SOHC / DOHC
MODULAR OIL PAN GASKET
4.6/5.4 Oil Pan Powdercoated Black
4V OIL PUMP PICK UP TUBE
4.6L DOHC & SOHC, 5.4L SOHC : LEFT .040
4.6L DOHC & SOHC, 5.4L SOHC : RIGHT .040
99-up 4V only Even Flow GEN 2 Head Cooling Mod
MODULAR CYLINDER HEAD STUD KIT
MODULAR CAM BOLT
4V HEADER GASKET (03-04) P.S.
4V HEADER GASKETS (03-04) D.S. (2 NEEDED)
4V TIMING CHAIN GASKET
4V TIMING COVER GASKET (center)
4V TIMING COVER GASKET
MODULAR REAR MAIN SEAL
Mach1 Intake Gasket ( requires 2 )
4V VALVE COVER GASKET (99-up)
4V VALVE COVER GASKET (99-up)
4V including SHELBY CAM CHAIN TENSIONER
4V including SHELBY CAM CHAIN TENSIONER
2V/3V/4V TIMING CHAINS
MODULAR FRONT CRANK SEAL
Mach 1 Upper Intake Gasket ( requires 2 )
Mach 1 Throttle Body Gasket
MODULAR PILOT BEARING
4.6 // 4V: Valve Springs Set of 32****
Ford 4.6L 4V Steel Retainer for 26123***
SAE : 5w30 Oil
Modular Oil Filter
Antifreeze (GREEN)
Vortech rebuild---APPRX
96-04 MUSTANG MOTOR MOUNTS **
96-04 4.6 Starter Kit Ford
Oil seperators / filters tbd ????
Remove Engine Assembly and Disassemble. Reassemble New Engine and Install in Vehicle. Break Engine In and Road Test
Added Charge for Removal and Installation of an Engine w/ a Power Adder ( ie. Supercharger or Turbocharger )
CUSTOM DYNO TUNING
__________________
Aluminator NA bottom end, rebuilt stock heads, Vortech V2, 3.90 gear, 514 RWHP, 468 RWTQ. Motor and tune by JPC. (Millersville, MD)
GR8 WYT is offline   Reply With Quote
Old 08-05-2012, 03:24 AM   #15
JGGilly12
Registered User
 
Join Date: Jun 2005
Posts: 47
Re: Official Vortech HP/TQ/mods thread

Stock bottom end: No, Aluminum Block bored .010 over, Forged Stroker Steel Racing Crankshaft by Kellogg, MANLEY 4340 Forged H-beam Rods(shotpeened, magnafluxed and weight matched), MANLEY Forged Notched Pistons with tool steel Pins and teflon skirts 9.5:1 CR, Total Seal Rings, ARP everything, Clevite Performance bearings, Melling Racing Oil pump teflon coated, 15/16 oil pickup, Felpro gaskets, 1 piece rear main seal, 7qt Oil Pan, Windage Tray

Head unit: Vortech V-1 S-Trim

Pulley size and boost level: 2.8RR pulley, 12ish psi(if I was lucky, with major slippage) Gone through 3 belts in a year and a half. Probably alignment though too!

Fuel system: Cobra Tank, Dual Ford GT Supercar Pumps, Fore Precision Billet Fuel Hat, 60lb Injectors, Zone 5 FPDM..

Tuner/Dyno shop info: Greg at Racers Edge Tuning in Downey, CA http://racersedgetuning.net/

Other notable mods: Stage 2 Ported and Polished Heads, Stainless Valves, Paxton A/A Innercooler, Anderson Boost Pipe, Vortech Mini-Race BOV, PMS HPX Slot MAF, Custom PCV Delete with Catch Can and breather for both Valve Covers, TKO600 with cryo treated gears, MGW Shifter, McLeod Twin Disc with Billet Flywheel, Lakewood Bellhousing, MM Firewall/Clutch Quadrant, JBA Shorties, Stock Cats with Custom 3.5" anti-reversion bubbles to 3" Magnaflow X pipe with SLP LM1s(custom done by Ed Hansons Muffler Shop in Spring Valley,CA), Energy Suspension Motor and Trans mounts, Ford Racing 4.10 Gears, Suspension goodies..

RWHP/RWTQ: 539/499 Peak HP was around 6200 and fell almost 100hp by the time it hit 7k.. Trying to find the culprit behind that still..

I just ordered an 8-rib kit and a 2.7RR pulley today! So as soon as I get them put on, ALIGNED PROPERLY this time and take the car to the dyno I will post the new numbers. Hopefully this time it doesnt slip like my current setup! Im going to be spinning the hell out of my little S-Trim but we'll see what she can do and go from there LOL. If anything I might do the 928 Motorsports Impeller upgrade.. Who knows. HAH. Im sure im missing some things in the above catagories but its pretty close off the top of my head.. Also going to Ford GT Cams and upgraded Springs as soon as the money is in my pocket! Then a new tune/new numbers again.. Gotta love the performance bug.
JGGilly12 is offline   Reply With Quote
Old 09-07-2012, 03:23 PM   #16
Krashdavus
Registered User
 
Krashdavus's Avatar
 
Join Date: Jan 2009
Location: Whitby, Ontario - Canada
Posts: 184
Re: Official Vortech HP/TQ/mods thread

Stock bottom end: Stock block [3,500 miles]

Head unit: V2 SCi Trim

Pulley size and boost level: Stock 3.6" [unknown, guessing 8-10 psi]

Fuel system: Stock deliverysystem with 47lb. Ford Injectors & Focus SVT fuel pump

Tuner/Dyno shop info: DCT in Toronto, Diego Lopes

Other notable mods: Anderson Power Pipe, Stock Exhaust Manifolds, Stock H-Pipe, Borla Catback (turbo design, not stingers), Devilsown Water/Meth Injection, 4.10 gears w/31 spline axles, SCT BA-2600 MAF

RWHP/RWTQ: 428/385 @ 19*timing

Last edited by Krashdavus; 09-07-2012 at 07:24 PM. Reason: corrections
Krashdavus is offline   Reply With Quote
Old 09-21-2012, 01:48 AM   #17
Chances50
Registered User
 
Join Date: Jun 2008
Location: Haskell, Ok
Posts: 1,325
Re: Official Vortech HP/TQ/mods thread

UPDATE

Stock bottom end: no forged 10.5:1 compression

Head unit: V2 S

Pulley size and boost level: 3.12 12psi

Fuel system: return style stealth 340 pumps and 80lb injectors

Tuner/Dyno shop info: Travis Franklin at Gearheads Performance

Other notable mods: Intercooler, power pipe, full exhaust

RWHP/RWTQ: 631rwhp 528rwtq on e85 23* timing

ET/MPH 10.69@129.98

just swapped to a SI blower no dyno numbers or ET's yet.
__________________
03 OW 5 speed 84k miles very clean. For sale!
Chances50 is offline   Reply With Quote
Old 09-21-2012, 05:20 AM   #18
hecdel40
Registered User
 
Join Date: May 2008
Location: Waveland MS
Posts: 326
Re: Official Vortech HP/TQ/mods thread

Great number
hecdel40 is offline   Reply With Quote
Old 09-21-2012, 09:34 AM   #19
04MACH!DSG
Registered User
 
04MACH!DSG's Avatar
 
Join Date: Jun 2008
Location: MI
Posts: 358
Re: Official Vortech HP/TQ/mods thread

Quote:
Originally Posted by Chances50 View Post
UPDATE

just swapped to a SI blower no dyno numbers or ET's yet.
Definitely will be interested to see how the SI #'s compare.
__________________
2004 Mach 1 Vortech V2-SQ, Powerpipe, BBK LT's, catted X-pipe, 4.10's, Roy's 7/8 spacer.

470 rwhp
410 rwtq
On a mustang dyno
04MACH!DSG is offline   Reply With Quote
Old 11-23-2012, 03:17 AM   #20
Chances50
Registered User
 
Join Date: Jun 2008
Location: Haskell, Ok
Posts: 1,325
Re: Official Vortech HP/TQ/mods thread

Never dynod with the SI head unit but went from 12lbs at 6300rpm to 15lbs at 6300 and 129mph to 134!
__________________
03 OW 5 speed 84k miles very clean. For sale!
Chances50 is offline   Reply With Quote
Old 01-28-2013, 12:20 AM   #21
elzuniga327
Registered User
 
Join Date: Sep 2010
Location: phoenix, arizona
Posts: 29
Re: Official Vortech HP/TQ/mods thread

Stock bottom end: yes

Head unit: v2 t trim

Pulley size and boost level: 3.48 11psi

Fuel system: 255lph, kb bap, 60# injectors, sct ba2400 maf (blow through)

Tuner/Dyno shop info: ernie/ vindictive motorsports/ extreme performance

Other notable mods: off road h and flowmasters

RWHP/RWTQ: 485/419
elzuniga327 is offline   Reply With Quote
Old 06-27-2013, 12:12 PM   #22
Mach828
Dark Knight
 
Mach828's Avatar
 
Join Date: Nov 2009
Location: Albuquerque, NM
Posts: 5,759
Re: Official Vortech HP/TQ/mods thread

Stock bottom end: Yes

Head unit: V2 S-Trim

Pulley size and boost level: 3.40 @ 6lbs and 3.125 @ 9lbs

Fuel system: Division X 340, pprv delete, wire upgrade, Cobra 39lb injectors

Tuner/Dyno shop info: DynoEdge

Other notable mods: 4.5" core air to air treadstone intercooler, Tial 50 bov, HPX maf, custom 4" powerpipe, stock runner ported intake, flowtech long tubes, 98 Cobra Cams, o/r x pipe, Borla catback, ac delete,

RWHP/RWTQ:

highest: 3.55 gears, 9lbs, 3.125" pulley stock lower, 16* timing
below that: 4.56 gears, 6 lbs, 3.40 pulley stock lower, 16* timing
below that: NA, bolt ons, cobra cams, 4.56 gears, 22* timing

Added a walbro 465, 60lb injectors, e85, and threw 23* of timing at it for the last graph showing 91 vs e85.


__________________

Vortech V2 S-trim, E85, A2A Treadstone, Comp cams, built engine, full exhaust, built rear, built 4r70, more mods.

Tuned by me with SCT Advantage

Last edited by Mach828; 05-09-2015 at 03:20 PM.
Mach828 is offline   Reply With Quote
Old 06-27-2013, 05:56 PM   #23
04MACH!DSG
Registered User
 
04MACH!DSG's Avatar
 
Join Date: Jun 2008
Location: MI
Posts: 358
Re: Official Vortech HP/TQ/mods thread

I have the v2 and running the 3.48" pulley, with and anderson power pipe, procharger a/a intercooler and I'm at about 11lbs

I am also running Vortech Race Bypass vavle. I do have long tubes and a ported stock runner length intake

I'm sitting around 470rwhp and 410rwtq on a mustang dyno
__________________
2004 Mach 1 Vortech V2-SQ, Powerpipe, BBK LT's, catted X-pipe, 4.10's, Roy's 7/8 spacer.

470 rwhp
410 rwtq
On a mustang dyno
04MACH!DSG is offline   Reply With Quote
Old 06-27-2013, 10:32 PM   #24
Roy
Registered User
 
Roy's Avatar
 
Join Date: Jul 2005
Location: S.E. Mich.
Posts: 3,446
Re: Official Vortech HP/TQ/mods thread

Post up your dyno graph.
Roy is offline   Reply With Quote
Old 09-04-2013, 12:18 PM   #25
lonestarbullitt
Registered User
 
Join Date: Aug 2011
Location: Helotes, TX
Posts: 179
Re: Official Vortech HP/TQ/mods thread

Stock bottom end: yes

Head unit: V2

Pulley size and boost level: 9lbs

Fuel system: 42 lb injectors, KB BAP, SVT Focus Fuel pump, lethal performance wiring upgrade.

Tuner/Dyno shop info: Lethal Performance, San Antonio TX

Other notable mods: long tubes, o/r x, magnapacks, air to water intercooler

RWHP/RWTQ: 449/413
lonestarbullitt is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:01 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<