2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Engine & Drivetrain (Including trans & rear axles)

Reply
 
Thread Tools Display Modes
Old 02-21-2007, 07:47 PM   #1
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
LDC Cooling mod install.

Figured I would share my fun with this great mod.

Just got it in the mail today.

I will install it tomorrow, with plenty of pictures.

MyLittlePony is offline   Reply With Quote
Old 02-21-2007, 07:50 PM   #2
DTMach1
semi-pro moderator
 
DTMach1's Avatar
 
Join Date: May 2004
Location: Virginia Beach
Posts: 4,955
Re: LDC Cooling mod install.

How much did it cost and where did you purchase it from?
__________________

2004 Mach 1
IUP/5spd/DSG
Engine, etc done...sits in the garage
DTMach1 is offline   Reply With Quote
Old 02-21-2007, 07:50 PM   #3
Fastbandit99
Back in Black
 
Fastbandit99's Avatar
 
Join Date: Feb 2006
Location: Lakeland, FL
Posts: 1,070
Re: LDC Cooling mod install.

Are those metal strips between the tiles?
__________________
Banditman
03 Black Mach 1
5 spd, K&N FIPK2, PHP spacer, MRT Catted h pipe, Magnaflow catback.
Fastbandit99 is offline   Reply With Quote
Old 02-21-2007, 08:38 PM   #4
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

Quote:
Originally Posted by DTMach1 View Post
How much did it cost and where did you purchase it from?

Here is all the info you need. http://www.ldcchicago.com/
MyLittlePony is offline   Reply With Quote
Old 02-21-2007, 08:40 PM   #5
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

Quote:
Originally Posted by Fastbandit99 View Post
Are those metal strips between the tiles?
Actually....it's a table top with slate tiles.
Allthough...I happen to own and operate a tile business.
So...if you ever need tile advice....I 've been doing it 16 years.
MyLittlePony is offline   Reply With Quote
Old 02-21-2007, 08:47 PM   #6
birdman941
Torque wins!
 
birdman941's Avatar
 
Join Date: Dec 2004
Location: Florida
Posts: 13,167
Re: LDC Cooling mod install.

I will be doing my own version of the cooling mod on "R".
May be simpler, yet just as effective.
And NO pulling the trans to do it.
Will have to pull lower intake though...................
__________________
The ORIGINAL Project R build thread is back !

5.4 32V NA
Streetable 404/387 26.56 MPG


"I don't like repeat offenders,
I like DEAD offenders" Ted Nugent

"A big engine hardly working is more efficient
than a little engine screaming its head off" Jay Leno
birdman941 is offline   Reply With Quote
Old 02-21-2007, 08:53 PM   #7
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

Well I have the trans out right now....waiting on a billet converter...

I could install this trans blindfolded by now.
MyLittlePony is offline   Reply With Quote
Old 02-22-2007, 11:16 PM   #8
Iceman
So. Florida Machin
 
Iceman's Avatar
 
Join Date: Sep 2003
Location: Fort Pierce , FL
Posts: 1,205
Re: LDC Cooling mod install.

Quote:
I could install this trans blindfolded by now.
i hear that!
__________________
03 oxford white mach

Boss 330 short block
procharger , cams ect...
666.4rwhp 558 rwtq
its got all the goodies!

"REAL STREET PERFORMANCE"
For all your mustang performance needs
Orlando ,Florida (407) 695 0699
Iceman is offline   Reply With Quote
Old 02-22-2007, 11:29 PM   #9
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

Couldn't get to it today....neighbor borrowed my extra jackstands for an xpipe install....took him 3 days!!! lol.

I have the afternoon free tomorrow to do this and take pics too.
MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 01:51 PM   #10
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

Here is the kit ready to go in. This was a great little project.
I would say a 4 out of 10, only because the trans would have to come
out to do it.





MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 01:59 PM   #11
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

First thing I did was take out a drain plug on the block. It's a litle different on a Mach than the instructions due to our aluminum block.

Bad picture....but this is on the driver side rear of block.

The small plug is the one that comes out...have a drain pan ready and it takes a 8mm allen socket. After you drain out the coolant....replace the plug
with a little liquid teflon sealer to make sure it won't leak. Do not tighten this
much more than a little past snug. You do not want to strip this out.


MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 02:04 PM   #12
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

Next....I disconnected the egr tube from the stock manifold and from the intake from up above. This needs to be able to be moved out of the way to
knock out the driver side freeze plug to install the new fitting.

Once disconnected...it can be moved out of the way.

It takes a 1 1/16 inch wrench. If your car is a dd or has some milage...spray this down with some solvent to aid in it's removal. Mine broke right loose.
But my car has never seen any weather.


MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 02:07 PM   #13
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

I took a small chisel and ball peen hammer and tapped the freeze plug on the driver side head at the very top of the plug. A few sharp taps popped it out
sideways like this. Then I used some pliers and pulled it out. Do not pry or mar
the freeze plug bore in the head.


MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 02:12 PM   #14
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

Wipe out the bore the freeze plug was in and then feel it with your finger....is it smooth? Clean? Ok then. EGR tube is movable...freeze plug out on driver side. Bore clean.

There is a bracket with two bolts tha must be loosened so the ear on the new driver side fitting will slide under the bracket and bolt flush to the head.

One bolt is a 10mm and the other is a 13mm. No need to remove....just loosen a 1/4 inch and pull braket back to make room for ear to slide under.

Couple pics: Bolt you see is the 10mm....this is driver side. 13mm is above it.

MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 02:17 PM   #15
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

The next step was to remove the 2 10mm bolts from the stock passenger side fitting. After those are out....I wiggeld the fitting straight out of the head. Took some small channel locks...squeezed the hose clamp and removed the stock fitting and tossed it aside.
MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 02:19 PM   #16
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

I lubed the o ring on the new driver side fitting with antifreeze and slipped it into the frezze plug bore. Tight fit....but easy enough. I left this loose for now...note ear that fits around 10mm bolt we loosened earlier. This ear goes
under the bracket.

MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 02:27 PM   #17
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

Here is the passenger side fitting in place. lube the o-ring with antifreeze and the hose ends...pop the fitting on the heater core line and slide it up...grip the clamp and re-install it. Pop the fitting in the head...and tighten the 2 10mm bolts. Gentle..no reason to be hercules on aluminum. snug. not too much.
I attache the hose on this side and tightened the clamp with an 8mm socket on a 1/4 drive ratchet. Don't crush the tube....but this one is important...so do not use a flat screwdriver....attach hose and clamp on driver side.

Almost done.
MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 02:33 PM   #18
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

I rotated the driver side fitting so the ear is arounf the bolt...under the old braket and tightened it all up. You will need to switch to wrenches here...
10 an 13m again....socket won't get on the bolts now.

Start the threads on the egr to manifold union...just start them and leave loose...now go and get the egr tube back into the intake....tighten it up,
then go below and tighten the egr to manifold.

Re-fill coolant. See threads here on that procedure. I can't start mine yet...
so I will have to wait.

MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 02:36 PM   #19
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

There is a bracket that holds the wiring harness at the very top of the bellhousing. It's a huge pain in the *** and must be removed and discarded.
It only hinders trans re-install anyway. Chuck it. Notice how I have new blue
crossover hose under wiring harness in last picture. This holds harness up
and out of the way. Bonus.
MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 02:41 PM   #20
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

Another shot of the driver side fitting in place....note ear under bracket...not over. This is critical....screw this up and it leaks.


Any questions?

Took less than an hour actual working time....

MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 03:32 PM   #21
SFMach1
Socom Shooter
 
SFMach1's Avatar
 
Join Date: May 2004
Location: CA
Posts: 418
Re: LDC Cooling mod install.

looks like a great job... so what's the benefit of doing this?
__________________
'04 DSG Mach 1, 5-speed
my mach 1 web page
SFMach1 is offline   Reply With Quote
Old 02-24-2007, 03:38 PM   #22
3150Mach1
Love my Mach
 
3150Mach1's Avatar
 
Join Date: Apr 2005
Location: Charlottesville, VA
Posts: 13,678
Re: LDC Cooling mod install.

Sweet install. Thanks for the pics. I need to get this kit when I upgrade the tranny and converter.
__________________
2003 slowmatic 11.105@117mph w/125 shot of Nitrous best to date
Kooks LTsw/OR X, elect cutouts, JLT RAI w/C&L 85 MAH,1" Spacer,PP Lower intake,Accufab TB,160 T-stat,EF Cooling Mod,NX Kit,Mez Electric Water pump,SLP Linelock,FRPP 4.10s-Alum Dif Cover-Alum Driveshaft & SL, Steeda Bumpsteer,MM Alum rack bushings,Deep Alum Tranny pan,Predator,Steeda AUCAs,MM ALCAs, Dspecs,MM CC plates & FLSFCs,MRT Guage cluster,AEM WB,MRT hood struts,Seq TLs, carbon fiber hood/trunk/Cobra wing,220 amp alt
3150Mach1 is offline   Reply With Quote
Old 02-24-2007, 03:40 PM   #23
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

The driver side head on a 4 valve motor has a dead spot in the rear 2 cylinders #7 and #8 for coolant flow. It creates a hot spot that could lead to detonation with a supercharger or nitrous. Most 4 valve engine failures are
either ringland/piston damage or broken rod due to tuning issues leading to
detonation or the air/fuel mixture igniting early while the piston is still on the compression stroke....piston is going up....flame front and gases expanding down....stresses the piston/rod was not designed to ever see= boom boom.

This evens out coolant temps in the heads and is basically an insuarnace policy and peace of mind for my blower install.
MyLittlePony is offline   Reply With Quote
Old 02-24-2007, 05:30 PM   #24
hawk
Braderunna
 
hawk's Avatar
 
Join Date: May 2004
Location: hampton, va
Posts: 4,949
Re: LDC Cooling mod install.

Very nice write up, and very clear photos. Thanks MLP!
__________________
"Sparky"- 2003 Azure Blue w/MT and IUP

Visit my garage on mach1mustang.org for details.
hawk is offline   Reply With Quote
Old 02-24-2007, 05:38 PM   #25
MyLittlePony
OG Mach1Misfit
 
MyLittlePony's Avatar
 
Join Date: Apr 2004
Location: Ofallon, MO
Posts: 1,543
Re: LDC Cooling mod install.

I wish I had better writing skills. But thank you!!

I really like doing installs and taking pictures to share.
I will be doing alot more now I have a decent Camera
and new laptop. Makes the whole picture thing a no
brainer now.

I would suggest this mod to anyone who has to have thier tranny out
for any reason.

I did alot of research and the apten cooling mod, evenflow and the others
do not compare to this one. Fit, finish and design are superior.

Make sure to fully understand the coolant re-fill procedure.
MyLittlePony is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:18 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<