2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Engine & Drivetrain (Including trans & rear axles)

Reply
 
Thread Tools Display Modes
Old 05-17-2018, 08:27 PM   #1
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Started with a vibration

So started with a vibration that the car has always had since i have owned it. Never really bothered me since it was only 120+mph. This winter i decided to play with it. The pinion angle was off so changed upper bushings.

Didnt help, thought maybe the alumium drive shaft was off balance put the factory shaft on... nope.

Decided to check the rear end. Pulled the cover and ooohhhh **** the spider gears are broke. Tear down and cleaning only damage spider gears. Waiting on parts

My 2 worries were a bent shaft in the trans but dosent appear to be. Ordered a slip yoke bushing since that was what went in my lasy mustang with similar vibration. Just assumed it was something else.

All in all glad i found the broken gears just a pain in the *** on my back. I miss having a lift
mikeracing is offline   Reply With Quote
Old 05-18-2018, 10:16 AM   #2
BONESTOCK
Registered User
 
Join Date: Jul 2004
Location: Raleigh , NC
Posts: 2,093
Re: Started with a vibration

Dang! Pic of the gears?
__________________
2004 Torch Red Procharged Mach 1
BONESTOCK is offline   Reply With Quote
Old 05-18-2018, 12:17 PM   #3
ab_mach1
Lorraine's driver
 
ab_mach1's Avatar
 
Join Date: Apr 2012
Location: Indianapolis, IN
Posts: 2,442
Re: Started with a vibration

Dang, that's crazy! Were they just holding on enough to function, just vibration? Lol, yeah I'd miss a lift too. Unfortunately, I've never been able to work with one. Thought about renting space at our local 'do it yourself' garage, but they want too much money.
__________________
  • Instagram: @azurblumach1
  • SCT X3 with LaSota Racing tune
  • Borla Stingers w/JBA off road H pipe
  • MGW short shifter w/comfort handle
  • Eibach Sportlines w/Koni STR.T's and Maximum Motorsports CC plates
ab_mach1 is offline   Reply With Quote
Old 05-18-2018, 01:56 PM   #4
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Started with a vibration

This post has my attention, was the vibration on deceleration only or all the time above 120?
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 05-18-2018, 04:26 PM   #5
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Re: Started with a vibration

All time

mikeracing is offline   Reply With Quote
Old 05-18-2018, 06:15 PM   #6
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,006
Re: Started with a vibration

Right there with you. Just busted mine too. Sounds like rocks rolling around in the diff when turning at slow speeds. Built this rear not even 10k miles ago...no track time, no hard launches, nothing more than a nitto 555r.

Time to find something better than a ford racing diff..
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁
311-420 is offline   Reply With Quote
Old 05-18-2018, 06:27 PM   #7
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Re: Started with a vibration

My issue is money was cheaper for parts than a new diff.

Replacement parts 300

Changing diff to some other type: gears, 31 spline axles, torsen 4:1. Shims = Way more.

If i was going to change the carrier i would want to do it all. I hate setting up gears so i would want to do everything. Right now the only thing that it really neads is seals, clutches and spider gears. Next time it comes apart it will be everything.

The rear has had 100's of burnouts, 200+ drag strip passes with full slicks and about 30 hours of open track time.
mikeracing is offline   Reply With Quote
Old 05-18-2018, 07:11 PM   #8
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,006
Re: Started with a vibration

Zero burnouts, zero hard launches, never tracked, never seen slicks and at 450rwhp mine are toast. Those little gears don't hold much and not for very long either.

It already has Moser 31s in there, ford racing 3.73s and ford racing 31 spline diff. Probably going to go with the eaton truetrac diff and pray the axles and ring/pinion are still ok.
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁
311-420 is offline   Reply With Quote
Old 05-21-2018, 08:46 PM   #9
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Re: Started with a vibration

Newest update after 3 different spider gear kits none work..... the pins are the wrong size or the gears are the wrong size for my carrier.

I give up.... ordering a yukon axle & carrier kit in 31 spline. Ford racing 4.10 and ford racing ring and pinion install kit.
mikeracing is offline   Reply With Quote
Old 05-25-2018, 11:13 PM   #10
BONESTOCK
Registered User
 
Join Date: Jul 2004
Location: Raleigh , NC
Posts: 2,093
Re: Started with a vibration

Quote:
Originally Posted by mikeracing View Post
Newest update after 3 different spider gear kits none work..... the pins are the wrong size or the gears are the wrong size for my carrier.

I give up.... ordering a yukon axle & carrier kit in 31 spline. Ford racing 4.10 and ford racing ring and pinion install kit.
Dang! Sucks but good too!
__________________
2004 Torch Red Procharged Mach 1
BONESTOCK is offline   Reply With Quote
Old 05-26-2018, 10:44 AM   #11
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Re: Started with a vibration

You know you married the right woman when you tell her you need to put the new diff in the freezer and the bearings in the oven. And her answer was OK !!!!
mikeracing is offline   Reply With Quote
Old 05-26-2018, 02:20 PM   #12
Phil
Nitrous Junkie
 
Phil's Avatar
 
Join Date: Jul 2003
Location: Ohio
Posts: 7,299
Re: Started with a vibration

Quote:
Originally Posted by mikeracing View Post
You know you married the right woman when you tell her you need to put the new diff in the freezer and the bearings in the oven. And her answer was OK !!!!
Lol! That's a keeper!

I remember putting an old set of steel rods in the oven to stress relieve them and my wife at the time was pissed!
__________________
Phil
PRB Machining, LLC
http://www.prbmachining-absdeleteman...com/index.html

Performance mods by Jeff Chambers, the owner/tuner of CRT Performance in Norwalk, Ohio
http://www.crt-performance.com/
Phil is offline   Reply With Quote
Old 05-28-2018, 10:07 PM   #13
BONESTOCK
Registered User
 
Join Date: Jul 2004
Location: Raleigh , NC
Posts: 2,093
Re: Started with a vibration

haha!! Just had just installed my twin disk and had the pilot bearing in my freezer for a night. She didn't mind one bit. So long as it was contained!
__________________
2004 Torch Red Procharged Mach 1
BONESTOCK is offline   Reply With Quote
Old 06-01-2018, 06:33 PM   #14
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Re: Started with a vibration

So set up the gears 30 + times bad pattern decided to change out pinion bearing and race and BAM right on the money 3 attempts. Was just like wTF the bearing and races were from the ford racing kit i was having to use .062 worth of shims to get it close. With the bearing in the kit. But .032 with national bearing and race
mikeracing is offline   Reply With Quote
Old 06-01-2018, 08:38 PM   #15
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Started with a vibration

I've done a set of gears... decided I hate doing gears... worked great but the second set I did, not so much so I took it to the pros. Maybe someday I will learn the tricks.

Glad it worked out for you!
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 06-01-2018, 09:10 PM   #16
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Re: Started with a vibration

This was my first set done in the car. And first set that wasnt a dana 80, ford 9 or tractor trailer rear end
mikeracing is offline   Reply With Quote
Old 06-02-2018, 01:35 PM   #17
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Re: Started with a vibration

Well one of those days. Decided to change the trans fluid. Left the fill plug loose to start and let it idle for a min. Plug fell out and so did 1 qt of fluid on the garage floor. Topped off took a test drive and everything is good to go.
mikeracing is offline   Reply With Quote
Old 06-02-2018, 05:40 PM   #18
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Started with a vibration

Not as bad as forgetting to tie up an oil feed line to turbo, oil feel line gets burned through and I dump all my oil on the street. You could see my path for months around the block. Destroyed my turbo and coated the entire underneath of the car in oil. that was a pain to clean up!
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 06-04-2018, 07:36 AM   #19
sutyak
it's soo-tack
 
sutyak's Avatar
 
Join Date: Nov 2002
Location: Fairmont, WV
Posts: 2,082
Re: Started with a vibration

Great to hear it's all buttoned up. Hopefully one day we cross paths. I can't remember the last time I saw a white Mach 1 out in the wild.
__________________
mark
2004 DSG Mach 1. Built motor. Turbo. 667whp
2006 Sonic Blue Focus. Built motor. Turbo. 12.4 @ 115mph (sold)
2003 DSG Mach 1. 12.65 @ 106 (sold)
sutyak is offline   Reply With Quote
Old 08-01-2018, 09:21 PM   #20
03Shadow Grey
Registered User
 
03Shadow Grey's Avatar
 
Join Date: Feb 2016
Location: Theodore Alabama
Posts: 282
Re: Started with a vibration

Quote:
Originally Posted by mikeracing View Post
Newest update after 3 different spider gear kits none work..... the pins are the wrong size or the gears are the wrong size for my carrier.

I give up.... ordering a yukon axle & carrier kit in 31 spline. Ford racing 4.10 and ford racing ring and pinion install kit.
**** mike I was excited till I read this,
I have the same issue with the spider gears . I found a guy selling a brand new carbon fiber clutch kit for 50$ and i"m thinking now the bearing and seal kit and spiders. No such luck finding the gears set , even the dealer wants to sell me the whole shebang for $480 28 spline.I have also read where the gt 8.8 set is too small some say its the same. I plan on calling a shop my friends use for there Jeep rebuilds and confirm to see what to do. Change it all they say but as you said that can get real expensive when all i need is spiders and refresh kit.
03Shadow Grey is offline   Reply With Quote
Old 08-25-2018, 08:56 PM   #21
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Re: Started with a vibration

So kinda gave up for a while borrowed my fathers vibration analyzer. Found the issue its the pinion flange it self is out of balance. HOW I HAVE NO IDEA!! ITS within tolerance for runout preload is good on the pinion.
mikeracing is offline   Reply With Quote
Old 08-27-2018, 08:12 AM   #22
sutyak
it's soo-tack
 
sutyak's Avatar
 
Join Date: Nov 2002
Location: Fairmont, WV
Posts: 2,082
Re: Started with a vibration

That's wild. What is a vibration analyzer and how is it used?
__________________
mark
2004 DSG Mach 1. Built motor. Turbo. 667whp
2006 Sonic Blue Focus. Built motor. Turbo. 12.4 @ 115mph (sold)
2003 DSG Mach 1. 12.65 @ 106 (sold)
sutyak is offline   Reply With Quote
Old 08-27-2018, 10:54 AM   #23
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Re: Started with a vibration

Its a device that measures vibration. Hahahaha


They use a accelerometer to measure vibration and its calibrated for up on the sensor and tells the rpm of the vibration. And has a strobe light line to show the location.

Then add weight to smooth it out. The key is finding the worst location at a given rpm. In my case the worst vibration was at the pinion then it was a toss up where tonstart. I started at the driveshaft only slightly changed the measurement, then added weight to the yoke and made a jump. Checked run out and no change


https://www.ebay.com/p/Kent-Moore-J-...er-2/656720445
mikeracing is offline   Reply With Quote
Old 08-27-2018, 12:18 PM   #24
TKat13
Mach-T
 
TKat13's Avatar
 
Join Date: Jun 2004
Location: DFW
Posts: 2,865
Re: Started with a vibration

Cool; but I want a video of how its done... you have my thinking what my vibration may be...
__________________
Darrell
Black '04 Mach 1
Track Times (bone-stock w/drs):60 ft - 1.90 | 1/8 - 8.67
(100 shot,E85,4:10s,Street tire):60 ft - 1.67 | 1/8 - 7.88
New build - 750rwhp; not track tested (yet)
Mods: Build Log
Paint&Body
Tuned by Manny @ HPP
TKat13 is offline   Reply With Quote
Old 08-27-2018, 12:29 PM   #25
mikeracing
MECHANIC
 
mikeracing's Avatar
 
Join Date: Jun 2012
Location: Morgantown, WV
Posts: 916
Re: Started with a vibration

https://m.youtube.com/watch?v=kj78G4wtXKE
mikeracing is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:43 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<