2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > "GO" Discussions > Engine & Drivetrain (Including trans & rear axles)

Reply
 
Thread Tools Display Modes
Old 03-07-2018, 09:29 AM   #1
shake this
Registered User
 
shake this's Avatar
 
Join Date: Oct 2004
Location: Lubbock, TX
Posts: 1,559
Engine Build Check List

So I just got a list if goodies from the machine shop and wanted to make sure we were missing anything or have any foreseeable issues before I give them the green light.

Donner is a Teksid block from a 1995 Lincoln Mark 8

Engine Block Cleaned
Engine Block Magnufluxed for Cracks
Engine Block, Cylinders Bored .020
ALIGN HONE MAINS
BHJ Torque Plate Hone .020 Digitally Balanced Rotating Assembly Internally balanced
Pistons Mounted on Connecting Rods
Crankshaft Grind .STD/.010
Crankshaft Polished and Vat Cleaned .STD/.010
Cylinder Heads Cleaned
Valve Job
Head Surfaced
CR868XPN .010TRI METAL ROD BEARINGS
MB5283XP STD TRI METAL MAIN SET
10227 MELLING HV OIL PUMP
HS26187PT HEAD GASKET SET
CS9790-4 LOWER GASKET SET
14042-8 Connecting Rods, 4340 H-Beam, Cap Screw, Bushed,
Ford,
594120C-8 Pistons, Forged, Dish, 3.572 in. Bore, Ford, Modular
V8, Set of 8
46620-8 MANLEY Piston Rings, Plasma-moly, 3.572 in. Bore,
File Fit, 1.5mm, 1.5mm, 3.0mm Thickness, 8-Cylinder, Set
156-5001 ARP SIDE MAIN BOLTS
156-5901 ARP MAIN STUD KIT WITH WINDAGE TRAY
156-4101 Cylinder Head Studs, Pro Series, Hex Head, Ford, 4.6,
5.4L, Kit
__________________
Steeda tri axe shifter
MRT H pipe w/Magnaflow cat back exhaust
JLT air intake
PHP intake spacer
Aluminum Driveshaft
SLP line-lock
4.10 gears
Moser axles
welded axle tubes
ET Radials
Dyno 300whp 318wtq n/a

415whp 515wtq NX 125 shot
Someone needs to slap the stupid outa you
shake this is offline   Reply With Quote
Old 03-07-2018, 09:42 AM   #2
DSG2003Mach1
700 HP Mach
 
DSG2003Mach1's Avatar
 
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
Re: Engine Build Check List

If you’re gonna spin it high or make big power make sure it gets billet oil pump gears.

I’d also upgrade the timing dowel

Why the over bore? If the block isn’t messed up I’d leave as much meat in the walls as possible

I’d probably put all new timing components in it and if you’re thinking about cams now would be the time to do springs and cams
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc...

'12 F150 FX2 Supercrew with Ecoboost daily beater
DSG2003Mach1 is offline   Reply With Quote
Old 03-07-2018, 09:45 AM   #3
shake this
Registered User
 
shake this's Avatar
 
Join Date: Oct 2004
Location: Lubbock, TX
Posts: 1,559
Re: Engine Build Check List

We will throw an Eaton on top with about 10-12lbs of boost running E85. Cams will push us over my budget, the machine work and bottom end was even a bit more than expected. Stuff gets expensive quick.

What do you suggest for the timing dowels, I'm no engine excerpt at all.
__________________
Steeda tri axe shifter
MRT H pipe w/Magnaflow cat back exhaust
JLT air intake
PHP intake spacer
Aluminum Driveshaft
SLP line-lock
4.10 gears
Moser axles
welded axle tubes
ET Radials
Dyno 300whp 318wtq n/a

415whp 515wtq NX 125 shot
Someone needs to slap the stupid outa you
shake this is offline   Reply With Quote
Old 03-07-2018, 10:14 AM   #4
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,005
Re: Engine Build Check List

I agree on not going .020 over unless you need to. Billet oil pump gears are great and nows the time. Also, how do they intend to magnaflux an aluminum block?
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁
311-420 is offline   Reply With Quote
Old 03-07-2018, 10:24 AM   #5
shake this
Registered User
 
shake this's Avatar
 
Join Date: Oct 2004
Location: Lubbock, TX
Posts: 1,559
Re: Engine Build Check List

Quote:
Originally Posted by 311-420 View Post
, how do they intend to magnaflux an aluminum block?
I'm sure they will use penetrating dyes to accomplish the same thing sense you can't actually magnaflux aluminum
__________________
Steeda tri axe shifter
MRT H pipe w/Magnaflow cat back exhaust
JLT air intake
PHP intake spacer
Aluminum Driveshaft
SLP line-lock
4.10 gears
Moser axles
welded axle tubes
ET Radials
Dyno 300whp 318wtq n/a

415whp 515wtq NX 125 shot
Someone needs to slap the stupid outa you
shake this is offline   Reply With Quote
Old 03-07-2018, 10:47 AM   #6
311-420
Can't be bridled
 
311-420's Avatar
 
Join Date: Sep 2007
Location: Texas
Posts: 7,005
Re: Engine Build Check List

Quote:
Originally Posted by shake this View Post
I'm sure they will use penetrating dyes to accomplish the same thing sense you can't actually magnaflux aluminum
That's cool, I've never heard of that before. But then again, I build semiconductors for a living, not ic engines.
__________________
2004 Mach 1 #6956 5spd w/IUP
Eaton swap, longtubes, built 3.73 SRA
452hp/409tq dynojet🏁
311-420 is offline   Reply With Quote
Old 03-07-2018, 11:06 AM   #7
01yellerCobra
Registered User
 
Join Date: Jan 2013
Location: San Diego, CA
Posts: 1,104
The Melling pump should have billet gears. I had a Melling pump in my old set up and it had billet gears.
__________________
New Ride:
2004 Mystichrome Cobra-Accufab SBTB and plenum, Steeda 2.8" upper, Bassani X, Borla Stingers, Mcleod RXT, MGW shifter, Level 5 halfshafts, chrome FR500's, Stiffler's FIT system and DS safety loop, GT pumps, BA3000, tuned by owner
01yellerCobra is offline   Reply With Quote
Old 03-07-2018, 11:42 AM   #8
shake this
Registered User
 
shake this's Avatar
 
Join Date: Oct 2004
Location: Lubbock, TX
Posts: 1,559
Re: Engine Build Check List

Quote:
Originally Posted by 01yellerCobra View Post
The Melling pump should have billet gears. I had a Melling pump in my old set up and it had billet gears.
Double checked with the machine shop, the Melling does have billet gears. Only mistake they made was on the pistons. Had some dished pistons ending up with 9.25 compression. Told him to figure some flat tops and we will be right at 10.8 with a .20 over bore. IF they have to bore it.
__________________
Steeda tri axe shifter
MRT H pipe w/Magnaflow cat back exhaust
JLT air intake
PHP intake spacer
Aluminum Driveshaft
SLP line-lock
4.10 gears
Moser axles
welded axle tubes
ET Radials
Dyno 300whp 318wtq n/a

415whp 515wtq NX 125 shot
Someone needs to slap the stupid outa you
shake this is offline   Reply With Quote
Old 03-07-2018, 01:38 PM   #9
DSG2003Mach1
700 HP Mach
 
DSG2003Mach1's Avatar
 
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
Re: Engine Build Check List

i thought the melling pump might but I wasnt 100%.

The timing dowel is basically a pivot point for the guide. The part that threads into the block is much smaller than the pivot point the guide sits on. When they fail its usually the block side so they drill and tap a bigger hole in the block to use a dowel with a larger diameter threaded side. At the proposed power level it sounds like youd be fine but again to do it later would be a real *****. If it does fail its probably taking the whole motor with it.

If they have to do more than hone it I would still suggest the absolute minimum bore increase to clean it up. Make sure they do the machine work first and THEN order pistons. It doesnt sound like you'll be pushing that hard now but why create problems later when big power would only be a blower swap away.
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc...

'12 F150 FX2 Supercrew with Ecoboost daily beater
DSG2003Mach1 is offline   Reply With Quote
Old 03-14-2018, 12:40 PM   #10
serviceman1
Registered User
 
serviceman1's Avatar
 
Join Date: Mar 2008
Location: derry nh
Posts: 302
Re: Engine Build Check List

I feel the pain on the expense but well worth doing everything the 1st time. I di mine 2 years ago, and dumped around $9000.00 all in. How about the heads will they get ported. If you are doing boost it is money well spent.
__________________
lifes to short to race anything else
serviceman1 is offline   Reply With Quote
Old 03-14-2018, 12:47 PM   #11
DSG2003Mach1
700 HP Mach
 
DSG2003Mach1's Avatar
 
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
Re: Engine Build Check List

Quote:
Originally Posted by serviceman1 View Post
I feel the pain on the expense but well worth doing everything the 1st time. I di mine 2 years ago, and dumped around $9000.00 all in. How about the heads will they get ported. If you are doing boost it is money well spent.
unless its a max effort build Im gonna go ahead and disagree. Im not a max effort build (not going class or grudge racing or anything) and NA SVT, my tuner and my builder all said not to bother porting the heads for my procharger setup. I make over 700 on E85 pretty easily, theres a decent amount still on the table to turn up my D1 further.
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc...

'12 F150 FX2 Supercrew with Ecoboost daily beater
DSG2003Mach1 is offline   Reply With Quote
Old 03-22-2018, 11:07 AM   #12
na svt
Registered User
 
na svt's Avatar
 
Join Date: Dec 2007
Location: beavercreek, oh
Posts: 4,695
Re: Engine Build Check List

Quote:
Originally Posted by shake this View Post
Double checked with the machine shop, the Melling does have billet gears. Only mistake they made was on the pistons. Had some dished pistons ending up with 9.25 compression. Told him to figure some flat tops and we will be right at 10.8 with a .20 over bore. IF they have to bore it.
10.4:1 with flat tops and a stock chamber volume.

E85 for fuel?

If you're getting studs, ensure those for the heads and the rod bolts are 2000s rather then the 8740s.
na svt is offline   Reply With Quote
Old 03-24-2018, 10:09 PM   #13
shake this
Registered User
 
shake this's Avatar
 
Join Date: Oct 2004
Location: Lubbock, TX
Posts: 1,559
Re: Engine Build Check List

Yes sir, running E85
__________________
Steeda tri axe shifter
MRT H pipe w/Magnaflow cat back exhaust
JLT air intake
PHP intake spacer
Aluminum Driveshaft
SLP line-lock
4.10 gears
Moser axles
welded axle tubes
ET Radials
Dyno 300whp 318wtq n/a

415whp 515wtq NX 125 shot
Someone needs to slap the stupid outa you
shake this is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:13 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<