|
12-17-2015, 07:19 PM | #126 |
Mach & Cheese
Join Date: Mar 2014
Location: Richmond VA
Posts: 797
|
Re: How to change your 5 speed to an automatic
I was going the cheap route with a Transgo AODE-3 Full Manual Kit for $209. Then Try to make my own relays.
I found this FB pic. It helps me somewhat. I think with more info I could make it myself for under $50. It says 8 pack relay but only shows 6, and I will not be using a transbrake. I don't understand from that pic how to wire the relays because the pic only show 1 or 2 wires going to what I think are the relays, but relays have 4-5 connections. |
12-17-2015, 08:11 PM | #127 |
Mach & Cheese
Join Date: Mar 2014
Location: Richmond VA
Posts: 797
|
Re: How to change your 5 speed to an automatic
Just found this diagram, and I can understand it .
What do you think? Run a 12v (+) from a momentary switch to the on pulse, and the 12v (+) from the brake light switch to the off pulse to run the TC lock up. Yes?. And maybe another of the same for OD operation. I don't think I will need to use the electronic pressure control wire because the Transgo kit adds a vacuum modulator valve to control the pressure put I still may need a pressure switch to keep from locking the TC at low pressure/low speed. Maybe the pressure switch would be wire to the Fused 12v (+) in the diagram? EDIT: did more reading. The pressure switch kicks the lock up off at high loads/pressure, and kicks OD off when downshifting so you don't forget to turn it off then upshift from 2nd to 4th. So I think it would need to be tied in on the same wire as the brake, and into the OD relay pack as well. Last edited by VA-Mach1; 12-17-2015 at 10:32 PM. |
12-24-2015, 01:11 AM | #128 |
Mach & Cheese
Join Date: Mar 2014
Location: Richmond VA
Posts: 797
|
Re: How to change your 5 speed to an automatic
Anybody? No hobbyists here? I understand buying things because someone else figured out how to make it work, but I want to know myself how things work. Guess Ill just buy some relays and a pressure switch and do some testing, and post results.
|
12-26-2015, 11:53 AM | #129 |
Transmission guy
Join Date: Nov 2006
Location: Mooresville, IN
Posts: 537
|
Re: How to change your 5 speed to an automatic
You're doing fine. I don't have the software to draw it up, but I'm pretty sure you could make those circuits latching on-off so that you can use a single momentary for each by adding 2 more relays and 2 more diodes. 1 extra relay and diodes would get you the latching circuit and the 2nd would provide the kill signal from brake input.
What are you drawing with?
__________________
|
12-26-2015, 02:15 PM | #130 | |
Mach & Cheese
Join Date: Mar 2014
Location: Richmond VA
Posts: 797
|
Re: How to change your 5 speed to an automatic
Quote:
|
|
01-13-2016, 05:48 PM | #131 |
Mach & Cheese
Join Date: Mar 2014
Location: Richmond VA
Posts: 797
|
Re: How to change your 5 speed to an automatic
After searching and reading more I found the info below. Redesigned the controller again and deleted the previous posts so no one gets bad info.
Latest info: White connector (10 pin connector) on the 4R70W harness mods – 1998 and up harnesses •Brown/orange wire gets switched to ground for lockup of converter. •Extend this wire and take it to a switch and then ground switch when closed. •Orange/yellow and Violet/orange wires get connected together and combine them into 1 wire that goes to a switch. When the switch is closed it gets switched to ground to control overdrive. •Solid red wire needs a 12 volt source because you’re using a different harness that wasn’t designed for this application. What I did was splice this wire into the solid orange wire on DTR sensor connector. *Note the wiring for pre1998 harnesses is different as they have different pin outs. Latest drawing: I think this one will actually work. |
01-18-2016, 09:28 AM | #132 |
Dark Knight
Join Date: Nov 2009
Location: Albuquerque, NM
Posts: 5,759
|
Darrin, what does it mean if I install the pump and I can't turn the trans by hand? It turned with the pump out just fine.
__________________
Vortech V2 S-trim, E85, A2A Treadstone, Comp cams, built engine, full exhaust, built rear, built 4r70, more mods. Tuned by me with SCT Advantage |
02-06-2016, 08:38 PM | #133 |
Mach & Cheese
Join Date: Mar 2014
Location: Richmond VA
Posts: 797
|
Re: How to change your 5 speed to an automatic
Latest version. Up to 11 relays. I'm sure there has to be a better way to build this but my electronic know how is not up to the task.
I have ordered all the relays and diodes and will be building and testing this version very soon. Last edited by VA-Mach1; 02-14-2016 at 10:26 AM. |
02-07-2016, 04:28 PM | #134 | |
Transmission guy
Join Date: Nov 2006
Location: Mooresville, IN
Posts: 537
|
Re: How to change your 5 speed to an automatic
Quote:
I hope you got it sorted out. What was almost surely wrong is that the transmission wasn't stacked correctly. Either the forward clutch or reverse clutch plates weren't fully seated and sitting on the splines of a friction. I am almost always available if anyone needs me, posting on forums isn't the best way to get me though. If your post goes in after another new post in a thread then no notification is sent. Call or email. My contact info is on my website bcatransmissions.com
__________________
|
|
02-07-2016, 04:30 PM | #135 | |
Transmission guy
Join Date: Nov 2006
Location: Mooresville, IN
Posts: 537
|
Re: How to change your 5 speed to an automatic
Quote:
D
__________________
|
|
06-22-2017, 05:15 PM | #136 |
Registered User
Join Date: Jun 2016
Location: Erlanven, Bavaria, Germany
Posts: 6
|
Re: How to change your 5 speed to an automatic
Hey Guys, I have a problem with ma tranny swap. But its a auto to manual swap.
I had swap all parts. Tremec 3650 Driveshaft Shifter Shifter Bezel Flywheel Clutch Clutch Pedal Manual Steering Column Manual Transmission Harness 2004 Mach1 ECU - TMX2 and a lot of small Parts... I know that i have to flash the ECU to disable or reset PATS. The Mach1 is in a Shop. The guys in this shop has swapped GT500 with auto Trans and some other big builts. All the ECU´s and files to flash came from Lund Racing. But we dont bring the car to start. My Mach1 is still 12 Months in the Shop for the swap... I have read about a Chip for the ECU to disable PATS. I found one who has swapped also from auto to manual. He used a "QuarterHorse" Chip from moates.net. Maybe someone has a solution. Sry for my not perfect english... Thanks for help and greetings from germany |
Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
|
|