notagt's 03 Ported Eaton/Cobra/T56 swap - Page 11 - 2003-04 Mach 1 Registry Owners Club

matthayn · 02-16-2016, 11:55 AM

I used to run 555R's and switched to Toyo R888s... I'll never run another tire on the street as long as these are available. Love em.

I have not tried MTs.

ASH302 · 02-16-2016, 01:05 PM

Quote:

Originally Posted by matthayn

I used to run 555R's and switched to Toyo R888s... I'll never run another tire on the street as long as these are available. Love em.

I have not tried MTs.

Heard great things about the r888s
They also look good too

ASh

311-420 · 02-16-2016, 04:24 PM

Stout numbers for those mods with regular pump gas! Congrats Larry.

555r work great up to a point. Temperature has a lot to do with how well they grab and whether or not the sun is hitting the street etc. During the day, mine hook well. If it's dark, it better be warm outside, otherwise it's a spin fest up to 60mph. I've never ran mickeys but from what I've gathered they need a good burnout before they do what they're known for. I don't drag race and I don't do burnouts so they'd be a pain for someone like myself.

sutyak · 02-16-2016, 07:00 PM

Quote:

Originally Posted by not a gt

Thanks ASH, ordered the plug and a new IC pump. I got down to Atlanta Saturday

It was cold so had a blanket on Machs engine. I got to Kurgan's Monday morning, and as usual went right in. What a guy, love going there, shared alot of info and tips, strapped her down and made 3 pulls. Final numbers were:

524 rwhp and 535 torque. 11:1 to 11.5 A/F, 15 psi boost, 70% FPDC, always forget the timing deal

No issues with cooling, even on hard pulls temps in 180 range. We discussed the unmetered air deal so I have the CFM oil cap and a K&N breather on each valve cover and capped off PCV lines.

I had put alot of coolant in IC tank and the flow was kinda slow , he thought I needed to dilute more since it was thick, I just went ahead and ordered a new IC pump from AM last night since I have no clue age/condition this was is in.

The IAT 2 sensor was wired wrong, he could tell by the temps. I looked at it last night and instead of shop splicing into the wire on the MAF connector itself, they had tapped into lines coming OUT of MAFia and couldn't verify colors so I am gonna redo that and maybe get a new sensor as well, I like to cover all bases.

That is about it, mount shaker, front clip, some detail work and ride. Thanks guys !!

Great numbers, and darn close to the estimate that you hoped for!

slojunk91 · 02-16-2016, 07:02 PM

Quote:

Originally Posted by not a gt

Thanks ASH, ordered the plug and a new IC pump. I got down to Atlanta Saturday

It was cold so had a blanket on Machs engine. I got to Kurgan's Monday morning, and as usual went right in. What a guy, love going there, shared alot of info and tips, strapped her down and made 3 pulls. Final numbers were:

524 rwhp and 535 torque. 11:1 to 11.5 A/F, 15 psi boost, 70% FPDC, always forget the timing deal

No issues with cooling, even on hard pulls temps in 180 range. We discussed the unmetered air deal so I have the CFM oil cap and a K&N breather on each valve cover and capped off PCV lines.

I had put alot of coolant in IC tank and the flow was kinda slow , he thought I needed to dilute more since it was thick, I just went ahead and ordered a new IC pump from AM last night since I have no clue age/condition this was is in.

The IAT 2 sensor was wired wrong, he could tell by the temps. I looked at it last night and instead of shop splicing into the wire on the MAF connector itself, they had tapped into lines coming OUT of MAFia and couldn't verify colors so I am gonna redo that and maybe get a new sensor as well, I like to cover all bases.

That is about it, mount shaker, front clip, some detail work and ride. Thanks guys !!

Congrats man!!!! Nice #'s!!!! I had a live feed on this at work yesterday hahaha!!!

not a gt · 02-17-2016, 12:42 AM

Thanks guys, one of the dyno pulls

https://youtu.be/Sd3j4iKcjZI

not a gt · 02-17-2016, 11:21 PM

I got with Kurgan, the #'s were with 19 degree timing, A/F 11:1 @WOT, IAT @130 is flat, then will slowly start to pulling timing, Low fan set to come on at 175, High fan at 182. I burped again today, still got some air, IC pump should be here tomorrow..shaker is a WIP.

TKat13 · 02-17-2016, 11:32 PM

glad to hear everything is back to normal and doing so well. congrats

ab_mach1 · 02-18-2016, 10:26 AM

Man Larry that's great! Congrats on this project!

As far a street tires, doesn't it seem like there is a limited selection for 17" wheels these days? I'm about to drop the hammer on a new set front and back. I was going to give Mickey Thompson Street Comp's a try, but I'm wanting to go with a 255 or 265 up front, which they don't even have. I want the tires to match, because I plan on getting a set of good DR's for the extra set of 17x9's I'll have. I bought a set of 17x10.5's when AFS started making them again back in November. I'll be interested in what you go with.

IG: @rcodemach1

Hpstang · 02-18-2016, 11:01 AM

Glad it's coming together man. That is a serious project for sure. Glad you went first so you can help me with mine lol

ASH302 · 02-18-2016, 11:07 AM

Quote:

Originally Posted by Hpstang

Glad it's coming together man. That is a serious project for sure. Glad you went first so you can help me with mine lol

Will agree with you on that
Larry will be big help to others on this information

ASh

not a gt · 02-18-2016, 11:22 AM

I got a line on a set of MT ET Street Radial Pro in 275/60/15 .Will these fit Mach with stock rear height? Great price and pretty new, where could I find a CHEAP rim that would fit Mach and these tires?? BHpstang, you know my barn is always open when you are ready, can even give you a loaner if needed !

Eruza, for street gonna probably go with a 275 MT ET Street S/S

http://www.mickeythompsontires.com/s...tem=ETStreetSS

Explosive · 02-18-2016, 11:24 AM

I believe a 28 will require a fender roll out back

not a gt · 02-18-2016, 11:30 AM

Quote:

Originally Posted by Explosive

I believe a 28 will require a fender roll out back

'
I figures that, plus I already have 6 black chrome rims and have to get 2 more for 315's..I may stick with my ET Street I have now in 26x11.5-17

http://www.mickeythompsontires.com/s...?item=ETStreet

Explosive · 02-18-2016, 11:36 AM

I've got some 26's on a 15x8 wheel that fit fine

TKat13 · 02-18-2016, 12:28 PM

I love my hoosiers, but only on a dry day.

Only tire I could find that would hook my setup. These are 18" rims and I run them at 22psi. They hooked on the street, I have yet to go to the track.

ASH302 · 02-18-2016, 12:53 PM

Quote:

Originally Posted by Explosive

I've got some 26's on a 15x8 wheel that fit fine

did you have to change out the rear brakes to run the 15's?

ASh

Explosive · 02-18-2016, 01:58 PM

Quote:

Originally Posted by ASH302

did you have to change out the rear brakes to run the 15's?

ASh

Nope, but i did change to stifflers brake lines but im going to be honest im not super crazy about the quality nor the crazy price, I'd have to dig out my invoice but i believe i was charged for handling...and shipping.....

Let me rummage my photobucket when i get a moment i think i took pics of my clearance.

Explosive · 02-18-2016, 04:54 PM

This was before i did the stifflers line

ASH302 · 02-18-2016, 05:24 PM

Looks pretty tight there

ASh

ASH302 · 02-18-2016, 05:24 PM

Quote:

Originally Posted by Explosive

Nope, but i did change to stifflers brake lines but im going to be honest im not super crazy about the quality nor the crazy price, I'd have to dig out my invoice but i believe i was charged for handling...and shipping.....

Let me rummage my photobucket when i get a moment i think i took pics of my clearance.

Which brand did you get?

ASh

Explosive · 02-18-2016, 05:29 PM

Tight for sure, I just got the cheap race stars, I'd like billet specialties but thats $$$. Mine are 15x8 out back

ASH302 · 02-18-2016, 06:19 PM

Which brand of brake lines

ASh

not a gt · 02-19-2016, 01:37 PM

Well in between alignment sessions went ahead and changed IC pump, not sure if they need to be primed, all I emptied was pulling hose off of lower fitting on exchanger, took about a gallon in tank along with a bottle of water wetter.

ASH302 · 02-20-2016, 09:45 PM

Dang Larry now I'm in the same boat as you with selling these UPR UCAs, i'm needing to get the adj ones.

ASh

02-16-2016, 11:55 AM	#251
matthayn Registered User Join Date: Dec 2010 Location: Jackson, TN Posts: 308	Re: notagt's 03 Ported Eaton/Cobra/T56 swap I used to run 555R's and switched to Toyo R888s... I'll never run another tire on the street as long as these are available. Love em. I have not tried MTs. __________________ 2003 Mach 1 Aluminator // Eaton @ 10lbs // T56 Magnum // E85 Build thread: http://www.svtperformance.com/forums...-Picture-Heavy IG: boostedmach

02-16-2016, 04:24 PM	#253
311-420 Can't be bridled Join Date: Sep 2007 Location: Texas Posts: 7,006	Re: notagt's 03 Ported Eaton/Cobra/T56 swap Stout numbers for those mods with regular pump gas! Congrats Larry. 555r work great up to a point. Temperature has a lot to do with how well they grab and whether or not the sun is hitting the street etc. During the day, mine hook well. If it's dark, it better be warm outside, otherwise it's a spin fest up to 60mph. I've never ran mickeys but from what I've gathered they need a good burnout before they do what they're known for. I don't drag race and I don't do burnouts so they'd be a pain for someone like myself. __________________ 2004 Mach 1 #6956 5spd w/IUP Eaton swap, longtubes, built 3.73 SRA 452hp/409tq dynojet🏁

02-17-2016, 12:42 AM	#256
not a gt Registered User Join Date: Mar 2007 Location: Waaayy out in the country,leave your GPS at home! Posts: 4,825	Re: notagt's 03 Ported Eaton/Cobra/T56 swap Thanks guys, one of the dyno pulls https://youtu.be/Sd3j4iKcjZI __________________ 2003 DSG Mach 1-03 Cobra Term/T56 swap: 2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear Tuned by B.Kurgan 601Hp/558/Tq

02-17-2016, 11:21 PM	#257
not a gt Registered User Join Date: Mar 2007 Location: Waaayy out in the country,leave your GPS at home! Posts: 4,825	Re: notagt's 03 Ported Eaton/Cobra/T56 swap I got with Kurgan, the #'s were with 19 degree timing, A/F 11:1 @WOT, IAT @130 is flat, then will slowly start to pulling timing, Low fan set to come on at 175, High fan at 182. I burped again today, still got some air, IC pump should be here tomorrow..shaker is a WIP. __________________ 2003 DSG Mach 1-03 Cobra Term/T56 swap: 2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear Tuned by B.Kurgan 601Hp/558/Tq

02-17-2016, 11:32 PM	#258
TKat13 Mach-T Join Date: Jun 2004 Location: DFW Posts: 2,865	Re: notagt's 03 Ported Eaton/Cobra/T56 swap glad to hear everything is back to normal and doing so well. congrats __________________ Darrell Black '04 Mach 1 Track Times (bone-stock w/drs):60 ft - 1.90 \| 1/8 - 8.67 (100 shot,E85,4:10s,Street tire):60 ft - 1.67 \| 1/8 - 7.88 New build - 750rwhp; not track tested (yet) Mods: Build Log Paint&Body Tuned by Manny @ HPP

02-18-2016, 10:26 AM	#259
ab_mach1 Lorraine's driver Join Date: Apr 2012 Location: Indianapolis, IN Posts: 2,442	Man Larry that's great! Congrats on this project! As far a street tires, doesn't it seem like there is a limited selection for 17" wheels these days? I'm about to drop the hammer on a new set front and back. I was going to give Mickey Thompson Street Comp's a try, but I'm wanting to go with a 255 or 265 up front, which they don't even have. I want the tires to match, because I plan on getting a set of good DR's for the extra set of 17x9's I'll have. I bought a set of 17x10.5's when AFS started making them again back in November. I'll be interested in what you go with. IG: @rcodemach1 __________________ Instagram: @azurblumach1 SCT X3 with LaSota Racing tune Borla Stingers w/JBA off road H pipe MGW short shifter w/comfort handle Eibach Sportlines w/Koni STR.T's and Maximum Motorsports CC plates

02-18-2016, 11:01 AM	#260
Hpstang Registered User Join Date: Apr 2015 Location: Kingsland ga Posts: 398	Re: notagt's 03 Ported Eaton/Cobra/T56 swap Glad it's coming together man. That is a serious project for sure. Glad you went first so you can help me with mine lol __________________ 2004 Mach 1 torch red, 5 speed, Borla stingers, off road Mac ss pro chamber, k&n drop in,sct x4 with custom dyno tune 308 rwhp 324 rwtq upr delete puck, MM flsfc, wild rides upper and lower torque box reinforcement kit. MGW shifter with standard handle, speed of sound pillar with dual aeroforce gauges,Bullitts black polished lip 17x8 front 17x10.50 nitto 555r's 315/35/17, smoked tail lights,smoked 3rd brake light. Engine dress up parts. It's only just the beginning procharger coming soon

02-18-2016, 11:22 AM	#262
not a gt Registered User Join Date: Mar 2007 Location: Waaayy out in the country,leave your GPS at home! Posts: 4,825	Re: notagt's 03 Ported Eaton/Cobra/T56 swap I got a line on a set of MT ET Street Radial Pro in 275/60/15 .Will these fit Mach with stock rear height? Great price and pretty new, where could I find a CHEAP rim that would fit Mach and these tires?? BHpstang, you know my barn is always open when you are ready, can even give you a loaner if needed ! Eruza, for street gonna probably go with a 275 MT ET Street S/S http://www.mickeythompsontires.com/s...tem=ETStreetSS __________________ 2003 DSG Mach 1-03 Cobra Term/T56 swap: 2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear Tuned by B.Kurgan 601Hp/558/Tq

02-18-2016, 11:24 AM	#263
Explosive Registered User Join Date: Jul 2010 Location: Michigan Posts: 876	Re: notagt's 03 Ported Eaton/Cobra/T56 swap I believe a 28 will require a fender roll out back

02-18-2016, 11:36 AM	#265
Explosive Registered User Join Date: Jul 2010 Location: Michigan Posts: 876	Re: notagt's 03 Ported Eaton/Cobra/T56 swap I've got some 26's on a 15x8 wheel that fit fine

02-18-2016, 12:28 PM	#266
TKat13 Mach-T Join Date: Jun 2004 Location: DFW Posts: 2,865	Re: notagt's 03 Ported Eaton/Cobra/T56 swap I love my hoosiers, but only on a dry day. Only tire I could find that would hook my setup. These are 18" rims and I run them at 22psi. They hooked on the street, I have yet to go to the track. __________________ Darrell Black '04 Mach 1 Track Times (bone-stock w/drs):60 ft - 1.90 \| 1/8 - 8.67 (100 shot,E85,4:10s,Street tire):60 ft - 1.67 \| 1/8 - 7.88 New build - 750rwhp; not track tested (yet) Mods: Build Log Paint&Body Tuned by Manny @ HPP

02-18-2016, 04:54 PM	#269
Explosive Registered User Join Date: Jul 2010 Location: Michigan Posts: 876	Re: notagt's 03 Ported Eaton/Cobra/T56 swap This was before i did the stifflers line

02-18-2016, 05:24 PM	#270
ASH302 Soldier for Christ Join Date: May 2009 Location: Willis, TX at The Daddy ASh Ranch Posts: 30,596	Re: notagt's 03 Ported Eaton/Cobra/T56 swap Looks pretty tight there ASh __________________ 2001 lazer red v6 Mustang coupe sold in Aug 2006 2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012 2013 grey 6 speed coupe GT Mustang Sold in Feb 2014 2013 RED Dodge Charger R/T Sold Nov 2014 2002 custom Blue 02 Auto Trans AM Sold June 2015 1998 Cobra Black Sold summer 2016 Current 2009 Ford F350 FX4 March 2017 (work truck) 2003 OW 5.0 Mach 1 Aug 2020 ASh

02-18-2016, 05:29 PM	#272
Explosive Registered User Join Date: Jul 2010 Location: Michigan Posts: 876	Re: notagt's 03 Ported Eaton/Cobra/T56 swap Tight for sure, I just got the cheap race stars, I'd like billet specialties but thats $$$. Mine are 15x8 out back

02-18-2016, 06:19 PM	#273
ASH302 Soldier for Christ Join Date: May 2009 Location: Willis, TX at The Daddy ASh Ranch Posts: 30,596	Re: notagt's 03 Ported Eaton/Cobra/T56 swap Which brand of brake lines ASh __________________ 2001 lazer red v6 Mustang coupe sold in Aug 2006 2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012 2013 grey 6 speed coupe GT Mustang Sold in Feb 2014 2013 RED Dodge Charger R/T Sold Nov 2014 2002 custom Blue 02 Auto Trans AM Sold June 2015 1998 Cobra Black Sold summer 2016 Current 2009 Ford F350 FX4 March 2017 (work truck) 2003 OW 5.0 Mach 1 Aug 2020 ASh

02-19-2016, 01:37 PM	#274
not a gt Registered User Join Date: Mar 2007 Location: Waaayy out in the country,leave your GPS at home! Posts: 4,825	Re: notagt's 03 Ported Eaton/Cobra/T56 swap Well in between alignment sessions went ahead and changed IC pump, not sure if they need to be primed, all I emptied was pulling hose off of lower fitting on exchanger, took about a gallon in tank along with a bottle of water wetter. __________________ 2003 DSG Mach 1-03 Cobra Term/T56 swap: 2.3L Whipple,3.37 Upper,4 lb.lower, ID 1000 injectors,LCD cooling mod,Billetflow idlers,200A Alt,oil cooler delete with MMR adapter plate,MM oil filter kit,FrozenBoost Heat Exchanger Flowtech L.T., Maganaflow O/R X with Magnapacks, FRRP D.S.,T-56 with 26 spline input shaft and anti venom mod with reverse lockout box, FR steel flywheel,Spec Stage 3+,Moser 31 spline axles,FR 3.73 gear Tuned by B.Kurgan 601Hp/558/Tq

02-20-2016, 09:45 PM	#275
ASH302 Soldier for Christ Join Date: May 2009 Location: Willis, TX at The Daddy ASh Ranch Posts: 30,596	Re: notagt's 03 Ported Eaton/Cobra/T56 swap Dang Larry now I'm in the same boat as you with selling these UPR UCAs, i'm needing to get the adj ones. ASh __________________ 2001 lazer red v6 Mustang coupe sold in Aug 2006 2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012 2013 grey 6 speed coupe GT Mustang Sold in Feb 2014 2013 RED Dodge Charger R/T Sold Nov 2014 2002 custom Blue 02 Auto Trans AM Sold June 2015 1998 Cobra Black Sold summer 2016 Current 2009 Ford F350 FX4 March 2017 (work truck) 2003 OW 5.0 Mach 1 Aug 2020 ASh

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)