|
|
Body, Chassis & Interior Body, Chassis and Interior mods/discussions |
|
Thread Tools | Display Modes |
06-15-2011, 12:25 AM | #1 |
Registered User
Join Date: Nov 2007
Location: Greenville, SC
Posts: 2,554
|
How to: LED gauge install (white like stock, not blue)
I think this site needs more step by step "how to"s. So I made this one.
Use this link http://www.mikefordmustang.com/write...er-mustang.php for the basics. Even though this is for a SN95 and not a Mach 1 everything is the same up until you get your gauge cluster loose from the car. There are two plugs that you need to press clips in with your finger while you wiggle them loose to get the gauge cluster loose from the car. Once you get the cluster loose from the car and flip it over to take out the bulbs you will run into a white case around it (see below). Use a star screw driver to get the brass screws out. At this point you are ready to take out the bulbs. You need to turn the white clips attached to the bulbs counter clockwise. They are small so a pair of needle nose pliers helped me alot. For me the bulbs were a MAJOR pain in the *** to get out the clips at first using only my hands. I then used a work set of gloves that have rubber on the fingers. Whatever you do make sure you don't squeeze the bulb too much or you could break it. Instead get a good grip with two fingers on the bulb, hold the white clip with a pair of needle nose pliers and pull apart. Now you are ready to put in your LED bulbs. It should look like this... Install the LED bulbs back into the gauges but do not install the white case around the back of the gauges yet. I'm going to tell you a short cut... Go install the gauges back in the car with the white case missing BUT BE CAREFUL not to hurt anything behind the gauges!!! Now plug in only the plug that is closest to the passenger side. This will allow you to see which bulbs are working and which aren't without having to take everything back apart. It should look like this... Now turn the lights on and you can see which bulbs are working and which aren't. For me at first only the far left and far right ones worked. I had to pull some back out and switch them around and some I had to just play with the LED bulb in the clip and how it was seated. After they all light up you are ready to reinstall. You will need to unplug them again to reinstall the white case. When you unplug the only plug in you used to light them up, again...BE CAREFUL. The white case keeps the green motherboard from becoming detached from the gauges. So hold it gently so it can't detach and move the plug side to side, not up and down like you normally might. After this you can use the first link again and just reinstall everything like you took it apart. Then your gauges should have gone from this.... STOCK to this NEW
__________________
03 white Mach1 JLT RAI | 1/2 spacer | Catback | 4.56s 7.76@87.8mph Last edited by Stopsign32v; 06-15-2011 at 12:45 AM. |
06-15-2011, 12:33 AM | #2 |
Registered User
Join Date: Nov 2007
Location: Greenville, SC
Posts: 2,554
|
Re: How to: LED gauge install (white like stock, not blue)
The bulbs are here http://www.superbrightleds.com/cgi-b....html%23ipanel and are the 74-xHP3
Now if you get the "cool white" bulbs your gauges will look like this... I like the factory look of white, just not the dim look. So I figured out you need to get the "warm white" The cool white is more of a 6000k HID look and the warm white is a pure 4500k HID white look.
__________________
03 white Mach1 JLT RAI | 1/2 spacer | Catback | 4.56s 7.76@87.8mph |
06-15-2011, 01:52 AM | #4 |
cruzmach1
Join Date: Sep 2009
Location: Bronx NY
Posts: 801
|
Re: How to: LED gauge install (white like stock, not blue)
Nice! Thanks for this!!!
__________________
2004 Mustang mach 1 (5-Speed) Vortech V-2 with intercooler 455RWHP & 396RWTQ Mustang Magic Tune 3/8 PHP Intake Spacer Mac 5/8 Long Tube Headers Mac Catted H-Pipe Magnaflow Cat Back Steeda Short throw shifter |
06-15-2011, 04:44 AM | #5 |
Soldier for Christ
Join Date: May 2009
Location: Willis, TX at The Daddy ASh Ranch
Posts: 30,596
|
Re: How to: LED gauge install (white like stock, not blue)
man thanks for the write up, i would agree for sure need more how to's and write ups, helps out alot, this one should become a sticky, also i'll prob be doing this soon, just alot better for seeing it and looks great,
would be kewl to switch mine to yellow, that would be nice, again thanks for the write up, really helpful ASh
__________________
2001 lazer red v6 Mustang coupe sold in Aug 2006 2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012 2013 grey 6 speed coupe GT Mustang Sold in Feb 2014 2013 RED Dodge Charger R/T Sold Nov 2014 2002 custom Blue 02 Auto Trans AM Sold June 2015 1998 Cobra Black Sold summer 2016 Current 2009 Ford F350 FX4 March 2017 (work truck) 2003 OW 5.0 Mach 1 Aug 2020 ASh |
06-15-2011, 07:44 AM | #6 |
oooooo snaaps....
Join Date: Jun 2007
Location: DALLAS, TX
Posts: 592
|
Re: How to: LED gauge install (white like stock, not blue)
does the dimming feature still work?
__________________
2003 DSG mach 1:best 1/4-12.81 at 106.0 spinning, new times soon. Performance: HPP tuned 390hp and 422trq on 4lbs precision 7675 billet wheel turbo kit...FRPP 4.10...RAM Powergrip clutch...SPEC billet steel flywheel...MGW shifter...FIORE quadrant...Steeda firewall adjuster...Roy's 1/2" intake spacer...EGR delete...HPM megabite Jr. upper and lower arms. Looks: 03 Cobra wheels...03 Sideskirts...01 Tail lights...01 Front bumper |
06-15-2011, 09:58 AM | #7 |
2K3MACH
Join Date: Nov 2007
Location: San francisco california
Posts: 1,707
|
Re: How to: LED gauge install (white like stock, not blue)
How many bulbs do u need to order ?
__________________
03 Torch Red Auto IUP 1 of 528 MODS: PERFORMANCE: Pypes M80 muffler exhaust ,Roush Subframe Connectors, Stock h-pipe(for now), Eibach Prokit, Bilstien shocks/struts APPERANCE: Mach 1 ID PLATE,"Ram Air" Shaker Emblems, Tinted Tail Lights,18x9/10 Matt Black FR500's, UPR auto shift ball w/ OD, Stock look for now |
06-15-2011, 10:08 AM | #8 |
Dark Knight
Join Date: Nov 2009
Location: Albuquerque, NM
Posts: 5,759
|
Re: How to: LED gauge install (white like stock, not blue)
Hell ya. Thanks man
__________________
Vortech V2 S-trim, E85, A2A Treadstone, Comp cams, built engine, full exhaust, built rear, built 4r70, more mods. Tuned by me with SCT Advantage |
06-15-2011, 10:09 AM | #9 |
Registered User
Join Date: Nov 2007
Location: Greenville, SC
Posts: 2,554
|
Re: How to: LED gauge install (white like stock, not blue)
yes
5
__________________
03 white Mach1 JLT RAI | 1/2 spacer | Catback | 4.56s 7.76@87.8mph |
06-19-2011, 04:50 AM | #10 |
Pilot
Join Date: Mar 2009
Location: West Grove, Pa
Posts: 653
|
Re: How to: LED gauge install (white like stock, not blue)
ive been thinking about doing this... what i really want to do is get rid of the green stuff in the center of the dash.. how do we ditch the green illumination of the heat/ac/trac control etc
__________________
04 TR mach. #6787 |
06-19-2011, 01:53 PM | #11 |
Its stock....No really!
Join Date: Jul 2005
Location: Albuquerque, NM
Posts: 4,433
|
Re: How to: LED gauge install (white like stock, not blue)
Id love to make everything blue in the car. Problem is my boost gauge is green to match the green gauge cluster and the green center console. Would be nice if all of it was blue. Just seems like alot of work and I dont think you can change the stock stereo to blue.
__________________
2003 Azure Blue Mach 1 5spd w/ IUP Mods: Lots of new stuff coming.....stay tuned |
06-19-2011, 03:01 PM | #12 |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: How to: LED gauge install (white like stock, not blue)
Just ordered mine! I'm guessing the bright white ones were the "warm white?" I didn't see any other white it could be.
Thanks for the write up and part #
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg |
06-19-2011, 10:26 PM | #13 |
Soldier for Christ
Join Date: May 2009
Location: Willis, TX at The Daddy ASh Ranch
Posts: 30,596
|
Re: How to: LED gauge install (white like stock, not blue)
i would like to do yellow, i guess simple question can yellow be done, i'm guessing it is what ever choice of bulb you go with and that is what you get???
ASh
__________________
2001 lazer red v6 Mustang coupe sold in Aug 2006 2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012 2013 grey 6 speed coupe GT Mustang Sold in Feb 2014 2013 RED Dodge Charger R/T Sold Nov 2014 2002 custom Blue 02 Auto Trans AM Sold June 2015 1998 Cobra Black Sold summer 2016 Current 2009 Ford F350 FX4 March 2017 (work truck) 2003 OW 5.0 Mach 1 Aug 2020 ASh |
06-20-2011, 12:05 AM | #14 |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: How to: LED gauge install (white like stock, not blue)
When I bought mine I saw the colors were:Soft white, Cool white (kinda blue), red, green (lime) blue, amber (yellow..) or purple. My order came out to $20.44 shipped.
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg |
06-20-2011, 01:53 AM | #15 | |
Soldier for Christ
Join Date: May 2009
Location: Willis, TX at The Daddy ASh Ranch
Posts: 30,596
|
Re: How to: LED gauge install (white like stock, not blue)
Quote:
ASh
__________________
2001 lazer red v6 Mustang coupe sold in Aug 2006 2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012 2013 grey 6 speed coupe GT Mustang Sold in Feb 2014 2013 RED Dodge Charger R/T Sold Nov 2014 2002 custom Blue 02 Auto Trans AM Sold June 2015 1998 Cobra Black Sold summer 2016 Current 2009 Ford F350 FX4 March 2017 (work truck) 2003 OW 5.0 Mach 1 Aug 2020 ASh |
|
06-20-2011, 01:53 AM | #16 | |
Soldier for Christ
Join Date: May 2009
Location: Willis, TX at The Daddy ASh Ranch
Posts: 30,596
|
Re: How to: LED gauge install (white like stock, not blue)
Quote:
ASh
__________________
2001 lazer red v6 Mustang coupe sold in Aug 2006 2004 screaming yellow 5.0 sc Mach 1 sold in Oct 2012 2013 grey 6 speed coupe GT Mustang Sold in Feb 2014 2013 RED Dodge Charger R/T Sold Nov 2014 2002 custom Blue 02 Auto Trans AM Sold June 2015 1998 Cobra Black Sold summer 2016 Current 2009 Ford F350 FX4 March 2017 (work truck) 2003 OW 5.0 Mach 1 Aug 2020 ASh |
|
06-20-2011, 02:11 AM | #17 |
Registered User
Join Date: Feb 2007
Location: Phoenix
Posts: 163
|
Re: How to: LED gauge install (white like stock, not blue)
Very cool, I had no idea we could even change out the bulbs. By the looks of it I will probably not be able to go with red because then it will all just be red, kind of a boring look picturing it
|
06-24-2011, 03:28 PM | #18 |
Registered User
Join Date: Feb 2007
Location: Phoenix
Posts: 163
|
Re: How to: LED gauge install (white like stock, not blue)
Anybody know what type of led buld we need for lights around the A/C knobs area?
|
06-24-2011, 04:31 PM | #19 | |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: How to: LED gauge install (white like stock, not blue)
Quote:
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg |
|
07-03-2011, 01:29 AM | #20 |
cruzmach1
Join Date: Sep 2009
Location: Bronx NY
Posts: 801
|
Re: How to: LED gauge install (white like stock, not blue)
Installed mine today! Went with green to match my Aeroforce Gauges. It sure was a pain in the a$$ to get all the LEDs on.
__________________
2004 Mustang mach 1 (5-Speed) Vortech V-2 with intercooler 455RWHP & 396RWTQ Mustang Magic Tune 3/8 PHP Intake Spacer Mac 5/8 Long Tube Headers Mac Catted H-Pipe Magnaflow Cat Back Steeda Short throw shifter |
07-03-2011, 08:39 AM | #21 |
Registered User
Join Date: Nov 2007
Location: Greenville, SC
Posts: 2,554
|
Re: How to: LED gauge install (white like stock, not blue)
Now THAT looks good my friend!!! Did you try my shortcut to checking all the LEDs?
__________________
03 white Mach1 JLT RAI | 1/2 spacer | Catback | 4.56s 7.76@87.8mph |
07-03-2011, 09:18 AM | #22 |
cruzmach1
Join Date: Sep 2009
Location: Bronx NY
Posts: 801
|
Re: How to: LED gauge install (white like stock, not blue)
Thanks! Yup I sure did
__________________
2004 Mustang mach 1 (5-Speed) Vortech V-2 with intercooler 455RWHP & 396RWTQ Mustang Magic Tune 3/8 PHP Intake Spacer Mac 5/8 Long Tube Headers Mac Catted H-Pipe Magnaflow Cat Back Steeda Short throw shifter |
07-10-2011, 12:50 AM | #23 |
Registered User
Join Date: Jul 2010
Location: Las Vegas
Posts: 7
|
Re: How to: LED gauge install (white like stock, not blue)
Thanks! nice how-to, just ordered the cool white LED's for mine
|
07-10-2011, 02:32 PM | #24 |
Mach-o-holic
Join Date: May 2010
Location: La La Land
Posts: 1,276
|
Re: How to: LED gauge install (white like stock, not blue)
Mine turned out really nice! I didn't take off the white cover on the back of the cluster for fear if messing up the mother board. I was able to remove and replace the bulbs with needle nose pliers. At first, only one bulb didn't work, so I bent the clip towards the white base of the fixture and it worked just fine. Thanks for the write up and buying info!!
__________________
2003 Mach 1 TR 5 Speed IUP Bolt ons: You name it! 4.10s too 2004 Cobra Screaming Yellow 2.3L Whipple Gear install vid https://www.youtube.com/watch?v=tJrAIDCpbDI Clutch Replacement Vid http://www.youtube.com/watch?v=UFr0Rur_EWc Wideband Install Vid http://www.youtube.com/watch?v=GmL1KBmWyhg |
07-10-2011, 08:04 PM | #25 |
Registered User
Join Date: Mar 2008
Location: Jersey Shore
Posts: 1,349
|
Re: How to: LED gauge install (white like stock, not blue)
This was the FIRST mod that I did to my Mach. I also put a red and blue LED in the AC knob It looks sweet! .... STILL havent been able to get git of the **** GREEEN odometer tho!
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|