|
|
02-20-2013, 05:51 PM | #1 |
Mach Underhood
Join Date: Feb 2012
Location: Oxnard California
Posts: 558
|
MMR intake spacer any good??
I've been wanting to raise my shaker up a bit since you can barely notice it. I heard if I buy an intake spacer it will raise the shaker and add performance?
MMR offers this spacer says 12 hp gain, is this what I'm looking for? Can anybody help with this.. thanks guys |
02-20-2013, 05:57 PM | #2 |
Registered User
Join Date: Nov 2005
Location: Lyndhurst, Ohio
Posts: 2,287
|
Re: MMR intake spacer any good??
Id say its a must have mod for Mach 1s !
__________________
Collecting for an Eaton Swap down the road.. |
02-20-2013, 06:33 PM | #3 |
Registered User
Join Date: May 2010
Location: Ohio
Posts: 378
|
Re: MMR intake spacer any good??
the gain is very minimal, but for $100 and a couple (1-3 probably) hp it doesnt hurt, plus as stated, it will raise the shaker. Should also be noted, the rubber water liner around the shaker will now rub your hood I went with the 1/2"
__________________
Ben - 04 Mach 1 -Mac LT, LP o/r x, Mangaflow cb, K&N CAI, MMR 1/2" spacer, Custom cams, degreed ftw 356/339 12.04 @ 113.9 -Is it bench racing if the car hasnt ran in a year? |
02-20-2013, 06:51 PM | #4 |
Mach Underhood
Join Date: Feb 2012
Location: Oxnard California
Posts: 558
|
Re: MMR intake spacer any good??
I was thinking 5/8ths or 1" , btw I don't have anything underneath the hood
|
02-20-2013, 07:22 PM | #5 |
Registered User
Join Date: Dec 2007
Location: beavercreek, oh
Posts: 4,695
|
Re: MMR intake spacer any good??
MMRs claimed gains are total bullshlt, always have been. With that, you will pick up a little power in the midrange. Check outtheir claims:
55-7hp for their ported heads 20hp for TBs 11hp MMR 96-04 GT/Cobra/Bullitt/ High performance Factory Airbox replacement kit 18rwhp electric water pump "big gains" IMRC deletes for 96-98s (this is proven to be a 3fwhp gain)
__________________
https://www.facebook.com/groups/481330828691064/ |
02-20-2013, 07:50 PM | #6 |
Registered User
Join Date: Nov 2007
Location: Greenville, SC
Posts: 2,554
|
Re: MMR intake spacer any good??
MMR is a total joke in general. That is my opinion anyways
__________________
03 white Mach1 JLT RAI | 1/2 spacer | Catback | 4.56s 7.76@87.8mph |
05-11-2014, 04:53 PM | #7 |
saving pennies
Join Date: Apr 2008
Location: Griffin, Ga
Posts: 1,487
|
Personally I would buy the intake spacer from the member here, his username is Roy, if he still sells them. That's where I got mine from. Nice to support the small guy that makes a quality piece and a forum member.
Sent from my XT1080 using Tapatalk
__________________
03 Mach 1--Auto, 4000 stall, 96 cobra intake cams, 4.10s, ARH L/T's, off road X, Moser 31 spline axles, Eaton Posi diff., MM FLSFC, Tokico D-Specs, k&n filter, 17x9/10.5s AFS Mac wheels 03 Cobra--18x9/10.5 TSW Nurburgring Wheels, Nitto NT05's 275/295, Stiegemeier ported, 2.87” pulley, Canton 9-qt oil pan, Spec Stage II clutch, MM coilovers, Bilstein Shocks/Struts, LFP heat exchanger, LFP radiator, Evans cooling system, 14" Brembo 4 Piston calipers, 470whp, 460ft-lbs |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|