|
|
Power Adders Superchargers, Turbos, Nitrous, etc... |
|
Thread Tools | Display Modes |
05-07-2013, 10:08 PM | #1 |
A.D.D. FTL
Join Date: Oct 2006
Location: Jacksonville, FL
Posts: 3,017
|
Getting a P1SC, let me know if I am missing anything!
Here is what I am getting:
- P1SC kit - "Upgraded" 3 core intercooler - SCT BA2400 MAF - 3.6 and 4.0 pulley What I have already: - SVT Focus pump - Cobra fuel pumps What I need: Injectors... 39? 60? Gauges and pod Bypass valve I am guessing I will most likely be needing to use the 4.0 pulley to keep the boost down to safe level. Which pump should I use? The Focus or Cobra? Focus is a direct replacement I think and I thought it would hold enough for 450 rwhp. I am guessing the Cobras are good for more but I don't know what I need to do to make them work. Also should I get some used 39# injectors or go with 60#? It is also missing the elbow from the intercooler, which I am guessing is a plastic elbow and will require a metal vband clamp type deal. I will post a picture and see what you guys think, maybe point me in a direction where I can find the elbow. What gauges should I get? Can y'all think of anything else? Last edited by HamMach1; 05-07-2013 at 11:48 PM. |
05-07-2013, 10:55 PM | #2 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Getting a P1SC, let me know if I am missing anything!
Not sure on that elbow, unless its an old design my 3 core from procharger looks a lot different
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
05-07-2013, 10:58 PM | #3 |
700 HP Mach
Join Date: Nov 2003
Location: Orlando, FL
Posts: 8,384
|
Re: Getting a P1SC, let me know if I am missing anything!
And is it missing the bypass valve or just not shown?
The 4" will get you just over 10psi and roughly 450 if turning 6700 or so
__________________
03 dsg mach1 - MPR built 9.5:1 motor, D1, cams, ported intake, full exhaust, magnum t56, built rear, E85 etc... '12 F150 FX2 Supercrew with Ecoboost daily beater |
05-07-2013, 11:28 PM | #4 |
A.D.D. FTL
Join Date: Oct 2006
Location: Jacksonville, FL
Posts: 3,017
|
Re: Getting a P1SC, let me know if I am missing anything!
|
05-08-2013, 09:23 AM | #5 |
cruzmach1
Join Date: Sep 2009
Location: Bronx NY
Posts: 801
|
Re: Getting a P1SC, let me know if I am missing anything!
I have a bosch By pass valve that came with my vortech that I could sell you
__________________
2004 Mustang mach 1 (5-Speed) Vortech V-2 with intercooler 455RWHP & 396RWTQ Mustang Magic Tune 3/8 PHP Intake Spacer Mac 5/8 Long Tube Headers Mac Catted H-Pipe Magnaflow Cat Back Steeda Short throw shifter |
05-08-2013, 02:01 PM | #6 |
A.D.D. FTL
Join Date: Oct 2006
Location: Jacksonville, FL
Posts: 3,017
|
Re: Getting a P1SC, let me know if I am missing anything!
Found a Proflo bpv last night, thanks though!
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|