Thread: Eaton Swap.....
View Single Post
Old 12-07-2011, 09:30 PM   #547
SHAKN' 04
Registered User
 
SHAKN' 04's Avatar
 
Join Date: Jan 2008
Location: Kyle, Texas
Posts: 2,285
Re: Eaton Swap.....

Quote:
Originally Posted by machgsxr View Post
ATTT: DANIEL

2r3z6312baa - Crank pulley /Harmonic Balancer
f1az6378a - washer for balancer
f5rz6a340b - bolt for balancer
2r3z6312ba - Supercharger Crank drive pulley
2r3z10153ca - Bracket that replaces stk. alt. on 99-01 Cobra’s and 03/04 Mach 1’s (Comes w/ pulley below if bought used)
yw7z8678aa - pulley for above bracket
2r3z6b209bc - Pulley bridge assembly for S.C. (If bought new it comes with the bridge, 2 idlers and tensioner)
(8678B) Idler pulley,timing cover pass. side
yw7z8678aa - pulley on drivers side of timing cover
(6D080) Timing cover (if bought new, it comes w/ pulley on drivers side and tensioner)
s5az6700a - timing cover seal
(10A313) Upper alternator bracket
(10153) Lower alternator bracket
(10346) Alternator
1U2Z-14S411-TA Electrical connector (alt. to harmness )
(6B209A) Tensioner on timing cover
2r3z8260ab - Radiator hose
2r3z8a593ab - Radiator hose
2r3z8k576aa - Radiator hose
2r3z8548aa - Water cross over pipe
(6881) Cobra oil cooler adapter
(6A642) Cobra Oil cooler
2r3z9002aa - Cobra fuel tank (optional)
2r3z9h307ab - Cobra fuel pump (optional)
2r3z9424bb - Lower intake
(6K775) Garrett factory intercooler
3U2Z-14S411-SSA IAT2 sensor connector
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c)
3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res.
2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block
2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new)
2r3z9l443da - Intercooler line that goes from hard line to hard line
f8yz8501aa - Ford / Bosche water pump for intercooler
2r3z8n500ac - Intercooler pump
2r3z8a193aa - Heat exchanger mounting bracket
2r3z8c386aa - 2each bracket clamps for h/e
(9N491B) Lower manifold to intercooler water adapter
2r3z9a589ca - Plenum
(9B659) Intake tube from maf to t/b.
(9F715) IAC valve
2r3z9a825aa - Cruise control cable
2r3z9a758aa - Throttle cable
(9728) Throttle and cruise control cable mounting bracket
1l3z12b579aa - MAF
(6C324) PCV tubing
(9F479) Sensor on the back of the S/C
(9E498) Hose's or tube cluster of connectors for the vacuum parts above
e83z9f670a IAC gasket
2r3z6020aa - Timing cover gasket LH side
2r3z6020ba -Timing cover gasket middle
2r3z6020ca - Timing cover gasket RH side
2r3z9h486aa - Lower intake to S.C. gasket
2r3z9l437bb - Plenum to S/C gasket
e6az9d476b - EGR gasket
2r3z3490aa - Power steering resevoir bracket.
I/C resivoir tank
i/c pigtail
S/C 8 rib belt
inner acc. belt.
n804178s309 - (8) Nuts for plenum, coolant crossover and pulley bridge can be picked up at local auto parts store in help section.
n805164437 - (1) Bolt for pulley cage to timing cover.
n808102s437 - bolt that is used on the idlers and pulleys. Only need if you buy parts seperately. You will need a total of at least 6 of these.
n808920s437 - Pulley bridge bolts
n606677-s36 (4) Bolts to bolt the bracket clamps to the h/e bracket
N605909s437 - (4) bolts for the upper alt. bracket
n807274s437 (1) lower alt. bracket to alt bolt
n811313s431 (4) studs to bolt plenum to s/c
w506404s437 (10) i/c to s/c bolts
[/QUOTE]

thank u sir! search is on!
__________________
**SOLD**04' Mach 1
-Comp Cams 106100's (deg 106/110)
-Eatonswap with 3.4 Pulley
-Full Exhaust (mac lts & xpipe, sss terminator c/b)
-Built Rear w/ 3.55 gears

[B]-Tuned by Lethal Performance of San Antonio
-510hp/478tq
SHAKN' 04 is offline   Reply With Quote