2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > Search Forums
Reload this Page Search Results
Photo Gallery $ Donations $ Register FAQ Community Calendar Today's Posts Search

Page 1 of 10 1 2345678910
Showing results 1 to 20 of 200
Search took 0.01 seconds. Search: Posts Made By: musclemerc
Forum: Mustangs Parts For Sale/Wanted 01-17-2019, 07:26 PM
Replies: 3
Views: 950
Posted By musclemerc
Re: NAZ ported short runner intake manifold + spacers + accufab throttle body

Nasty NAZ.....
Forum: Mustangs Parts For Sale/Wanted 08-28-2018, 09:49 PM
Replies: 4
Views: 937
Posted By musclemerc
Re: I Need A Front Timing Cover

I have one in excellent condition
Forum: Power Adders 03-07-2018, 08:13 PM
Replies: 3
Views: 1,022
Posted By musclemerc
Re: 2011 GT500 Supercharger Fit?

Check out cobraengineering.com James Hell makes a kit to retrofit


I just got done with a TVS 2300 SC install from a gt500.
Forum: Engine & Drivetrain (Including trans & rear axles) 09-19-2017, 09:09 PM
Replies: 2
Views: 1,798
Posted By musclemerc
Re: Wire tucking the rear wires (Injector harness)?

Very clean.

Is that a 2.1 KB under the shaker? Been a minute since I saw one
Forum: Engine & Drivetrain (Including trans & rear axles) 06-11-2016, 10:19 AM
Replies: 12
Views: 2,751
Posted By musclemerc
Re: Lubelocker vs RTV rear differential seal

Lubelocker over here. No leaks for 3 years running plus you can reuse the same gasket up to 5 times.

WIN
Forum: Power Adders 06-07-2015, 08:50 PM
Replies: 16
Views: 2,499
Posted By musclemerc
Re: procharger crankcase venting

Yep.....

Closed loop....
Forum: Power Adders 06-07-2015, 09:29 AM
Replies: 16
Views: 2,499
Posted By musclemerc
Re: procharger crankcase venting

Crankcase vacuum is a good thing....
Forum: Wheels & Tires 03-06-2015, 08:32 AM
Replies: 4
Views: 1,121
Posted By musclemerc
Re: $100 Coupon for Discount Tire Ebay

Just made an order.

Thanks!!
Forum: Engine & Drivetrain (Including trans & rear axles) 03-02-2015, 06:10 PM
Replies: 5
Views: 1,031
Posted By musclemerc
Re: Anyone know the thread count on the egr tube?

Believe it or not a 5/8" brass crush coupling will fit over the EGR tube

Honestly if the intake spacer is 3/8" you wont need one.
Forum: Power Adders 01-31-2015, 08:48 AM
Replies: 10
Views: 2,406
Posted By musclemerc
Re: COT Risers for your Centrifugal build. No more hunting down a modified COT...

Jerry makes top quality stuff.
Forum: Power Adders 01-27-2015, 08:28 AM
Replies: 94
Views: 26,730
Posted By musclemerc
Re: TTSaleen's Eaton Swap Mach 1 project

There's no doubt its a cooling mod Zack.

The Mach1 has the fitting at the back of the cylinder head that feeds the heater core. Tying the 2 together kills the dead end behind the DS cylinder head.
Forum: Power Adders 01-24-2015, 09:38 AM
Replies: 11
Views: 2,233
Posted By musclemerc
Re: Coolant Crossover Tech (Eaton Swap)

I would love to see a pic of what you did.

Most Marauder guys modify the stock COT and shorten the riser section on both sides.

Jerry now makes a COT (looks like the Trilogy) he now offers to...
Forum: Power Adders 01-22-2015, 05:33 PM
Replies: 11
Views: 2,233
Posted By musclemerc
Re: Coolant Crossover Tech (Eaton Swap)

I found some info but it looks like the OP deleted all the pics.

Here is some info Zack posted awhile back see post #19:
...
Forum: Power Adders 01-22-2015, 05:22 PM
Replies: 11
Views: 2,233
Posted By musclemerc
Re: Coolant Crossover Tech (Eaton Swap)

Have you tried the stock COT with everything in place?

IIRC the Mach1 COT will clear the Eaton utilizing Marauder swap brackets without any modification. I'm not a fan of the finished look of the...
Forum: Power Adders 01-10-2015, 07:40 AM
Replies: 94
Views: 26,730
Posted By musclemerc
Re: TTSaleen's Eaton Swap Mach 1 project

Post up a pic of the cooling mod installed with the SC lower in place.

Does that fitting clear the lower?
Forum: Power Adders 01-02-2015, 12:40 PM
Replies: 17
Views: 4,321
Posted By musclemerc
Re: Need some pulley advice - Eaton Swap

Ha! Small world. I live a short distance away from McInnis Elect. And guess what? I'm a fiber technician, both ISP/OSP

Best of luck with your build.
Forum: Power Adders 12-31-2014, 11:05 PM
Replies: 17
Views: 4,321
Posted By musclemerc
Re: Need some pulley advice - Eaton Swap

I'm running a 7.5" lower with a 3.0 upper making 13.5psi
Forum: Power Adders 12-28-2014, 10:09 AM
Replies: 14
Views: 1,711
Posted By musclemerc
Re: cobra shortblock and procharger.. bad idea?

http://www.mach1registry.org/forums/showthread.php?t=132507
Forum: Power Adders 12-26-2014, 06:54 PM
Replies: 14
Views: 1,711
Posted By musclemerc
Re: cobra shortblock and procharger.. bad idea?

It's a D1SC, crank up the boost, run more timing, and have some fun :COOL:
Forum: Engine & Drivetrain (Including trans & rear axles) 12-26-2014, 06:51 PM
Replies: 6
Pvc
Views: 1,129
Posted By musclemerc
Re: Pvc

PVC= white plastic pipe
PCV= Primary Crankcase Ventilation

:3amin:
Showing results 1 to 20 of 200
Page 1 of 10 1 2345678910

 
Forum Jump

All times are GMT -4. The time now is 05:29 PM.

Contact Us - www.Mach1Registry.Com - Archive - Privacy Statement - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<