2003-04 Mach 1 Registry Owners Club  

Best Mustang Parts

Go Back   2003-04 Mach 1 Registry Owners Club > Search Forums

Showing results 1 to 20 of 200
Search took 0.39 seconds.
Search: Posts Made By: JDraper
Forum: Mach 1 Specific Event(s) 05-22-2018, 07:52 PM
Replies: 144
Views: 10,141
Posted By JDraper
Re: 2018 All-Ford Nationals at Carlisle, PA.

Yep..same here. 2 cars washed and waxed, one to go.
Forum: Mach 1 Specific Event(s) 05-18-2018, 06:34 PM
Replies: 144
Views: 10,141
Posted By JDraper
Re: 2018 All-Ford Nationals at Carlisle, PA.

We will provide 1 coffee cup, 2 travel mugs, a license plate holder and a ball hat for the raffle/giveaway.
Forum: Mach 1 Specific Event(s) 05-14-2018, 11:46 AM
Replies: 144
Views: 10,141
Posted By JDraper
Re: 2018 All-Ford Nationals at Carlisle, PA.

We are adding 2 more to our count for Friday and Saturday.. Chuck and Michelle Bennett.

We will bring cookies, dessert and a couple of "healthy" sides.

What are we lacking for the BBQ? ...
Forum: General Registry Discussion 05-03-2018, 05:08 PM
Replies: 73
Views: 1,999
Posted By JDraper
Re: 2018 Plans for your car.

Mine is getting a new set of Michelin Pilot's in the next couple of days.
Forum: General Registry Discussion 04-29-2018, 07:50 PM
Replies: 14
Views: 407
Posted By JDraper
Re: All your eggs in one Basket

That's what happens when you let bean counters run a business instead of letting business savvy individuals run the show. Accountants are needed to make sure the money is accounted for and where...
Forum: General Registry Discussion 04-23-2018, 09:18 AM
Replies: 6
Views: 213
Posted By JDraper
Re: 2003 mach1 help!!

I've built several rear ends for Ford 8" 8.8" and 9" rears and you do use a torque wrench to measure the resistance, just not your standard ft-lb wrench. It requires an in-lb wrench to get accurate...
Forum: General Registry Discussion 04-18-2018, 10:16 AM
Replies: 10
Views: 226
Posted By JDraper
Re: Happy Mustang Day!!!!

Happy Mustang Day! Now if the weather would only cooperate to drive them!

http://www.mach1registry.org/forums/attachment.php?attachmentid=66472&d=1504132376
Forum: General Registry Discussion 04-15-2018, 10:51 AM
Replies: 16
Views: 379
Posted By JDraper
Re: What is old is new!

Same here..have been running the MGW Mach 1 gripper knob since 2004 with the factory knob sitting in a box in the garage.
Forum: General Registry Discussion 03-19-2018, 08:41 PM
Replies: 67
Views: 2,823
Posted By JDraper
Forum: Mach 1 Specific Event(s) 03-16-2018, 02:30 PM
Replies: 144
Views: 10,141
Posted By JDraper
Forum: Mach 1 Specific Event(s) 03-14-2018, 04:04 PM
Replies: 144
Views: 10,141
Posted By JDraper
Re: 2018 All-Ford Nationals at Carlisle, PA.

We're in (3) for all :). will figure out what we're bringing for the BBQ/Raffle later.
Forum: Car Shows, Cruises & Get Togethers 03-12-2018, 05:27 PM
Replies: 6
Views: 355
Posted By JDraper
Re: 14th annual Crab Run

We're out too this year. We're returning from the lake that day :(
Forum: Engine & Drivetrain (Including trans & rear axles) 03-11-2018, 04:00 PM
Replies: 1
Views: 131
Posted By JDraper
Re: Cleveland won't start

You could have a cracked coil (even though it is new) that works fine when cold, but expands with heat and shorts out. You say you have a new coil, was it replaced before the problem occurred or...
Forum: General Registry Discussion 02-24-2018, 03:30 PM
Replies: 151
Views: 8,746
Posted By JDraper
Re: Back in the day members

Original owner here as well. Just rolled over 50k on the car.
Forum: General Registry Discussion 02-01-2018, 10:09 AM
Replies: 9
Views: 423
Posted By JDraper
Re: 1st '69 Mach1 SJC 4.30 ordered found

About an hour and a half from me...Love to have found that...
Forum: Other Mustangs/Fords For Sale/Wanted 01-30-2018, 11:26 AM
Replies: 0
Views: 948
Posted By JDraper
71-73 Mustang

Interested in finding a 71-73 Mustang convertible for a project. I'm not looking for a restored vehicle or one in pristine condition. Outside of a convertible, the model/engine isn't critical. ...
Forum: Tuning & Dyno Testing/Results 01-29-2018, 04:55 PM
Replies: 15
Views: 2,865
Posted By JDraper
Re: Intake Spacer Dyno Results

I did dyno runs back to back without and with the spacer. I can't find the dyno sheets, but I did find the rpm-hp-torque data dumps. Without the spacer, I crossed 300 ft-lb tq at 3900 rpms, with...
Forum: Engine & Drivetrain (Including trans & rear axles) 01-27-2018, 10:45 AM
Replies: 8
Views: 625
Posted By JDraper
Re: K&N RAI really this hard to service?

It's not hard to do at all. Just serviced mine 2 weeks ago. Just be careful not to over oil the filter or it will mess up your MAF sensor.

Disconnect the one bolt that holds the cover to the...
Forum: Mach 1 Specific Event(s) 01-25-2018, 12:26 PM
Replies: 144
Views: 10,141
Posted By JDraper
Re: 2018 All-Ford Nationals at Carlisle, PA.

They will add more rooms for the M1R as we need them, unless the hotel is completely full.. :)
Forum: Mustangs Parts For Sale/Wanted 01-17-2018, 12:26 PM
Replies: 13
Views: 1,428
Posted By JDraper
Re: Chrome Mach 1 fuel door

We can send it to my friend Jon to get it powdercoated when the pan goes.
Showing results 1 to 20 of 200

 
Forum Jump

All times are GMT -4. The time now is 11:24 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<