Forum: General Registry Discussion
08-23-2019, 09:39 PM
|
Replies: 15
Views: 1,304
Re: But they won't build a Mach 1
Here in Fresno there are no less than 7 Bullitts at one of the local dealerships. All priced well over $50,000. 2 black ones and 5 green
If they build a new Mach 1 I suggest the 5.2 liter out of...
|
Forum: General Registry Discussion
04-16-2019, 02:13 AM
|
Replies: 16
Views: 1,488
|
Forum: NEW Mach 1 Owner Introductions
02-01-2019, 09:04 PM
|
Replies: 12
Views: 1,828
Re: Better late than never?
Welcome!
I can't remember the width of my rear rims, but they fit 315s nicely and sit flush with the fenderwell. I have 275s out front equally pretty. They are aftermarket 03 Cobra knock off rims.
|
Forum: General Registry Discussion
11-24-2018, 03:37 PM
|
Replies: 15
Views: 1,759
Re: Finally Picked One Up
Yeah. I don't get the 03-04 Cobra nose on a Mach 1 thing either. The only other nose that seems to look sharp on them is the 99-01 Cobra nose.
|
Forum: NEW Mach 1 Owner Introductions
09-01-2018, 02:35 AM
|
Replies: 11
Views: 1,343
|
Forum: Engine & Drivetrain (Including trans & rear axles)
06-30-2018, 03:16 PM
|
Replies: 7
Views: 1,145
Re: MT82 in a Mach 1 possible?
Yeah. I agree. In the long run it would probably be easier to get a .5 OD T-56 in there than it would to get the MT-82 to work.
This idea came from realizing why the automatic 10-Speed is so much...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
06-27-2018, 11:54 PM
|
Replies: 7
Views: 1,145
Re: MT82 in a Mach 1 possible?
Yeah I did consider the GM ratio T-56 with the .5 OD the only other option since the Cobra T-56 only offers a tweener OD ratio on it's way to the same OD ratio my stock tranny has.
The MT82 just...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
06-24-2018, 10:01 PM
|
Replies: 7
Views: 1,145
MT82 in a Mach 1 possible?
So the 5.0 and 4.6 are pretty similar. Any idea how hard it would be to put a 2011-2017 MT82 behind a 4V 4.6 in our Mach 1s?
After doing some research I figured out there is almost no advantage...
|
Forum: General Registry Discussion
05-02-2018, 02:39 AM
|
Replies: 14
Views: 2,135
Re: All your eggs in one Basket
If Ford was making enough money on them they wouldn't get rid of them. Gas is still cheap enough here that people get less efficient SUVs and crossovers instead of Focus, Fiesta, Fusion. Market is...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
05-01-2018, 12:31 PM
|
Replies: 5
Views: 1,168
|
Forum: Engine & Drivetrain (Including trans & rear axles)
04-21-2018, 09:12 PM
|
Replies: 4
Views: 1,018
|
Forum: Engine & Drivetrain (Including trans & rear axles)
04-17-2018, 09:08 PM
|
Replies: 4
Views: 1,018
Re: Can GM T-56 guts swap into Ford T-56?
Yeah. That's why the .5 overdrive is so appealing to me. 4.30s and the same as stock cruising RPM with a boost to all the other gears that need it. I'll try and get an answer on some other forums if...
|
Forum: Tuning & Dyno Testing/Results
04-15-2018, 06:55 AM
|
Replies: 8
Views: 1,795
Re: My Dyno Session with Mach 1
Why is your horsepower peaking so low? Power on these cars usually peaks at around 6000 RPM. Also there is only a 500 RPM spread between the torque and horsepower peak? That looks way wrong.
|
Forum: Engine & Drivetrain (Including trans & rear axles)
04-07-2018, 02:22 PM
|
Replies: 4
Views: 1,018
Can GM T-56 guts swap into Ford T-56?
So as far as I can tell there's absolutly no performance advantage to swapping my Mach 1s' 5-Speed for a Cobra 6-Speed. The only thing the Cobra 6-Speed offers is a tweener overdrive gear that halves...
|
Forum: General Registry Discussion
03-26-2018, 03:23 AM
|
Replies: 2
Views: 889
|
Forum: General Registry Discussion
03-08-2018, 08:58 PM
|
Replies: 122
Views: 16,227
Re: 2018 Plans for your car.
I have CAI, BAMA tune, ported and matched exhaust manifolds with full BBK exhaust. I am thinking maybe 96 Cobra intake cams would finish it off? Can't remember if those cams effect smog though....
|
Forum: Engine & Drivetrain (Including trans & rear axles)
01-08-2018, 02:59 PM
|
Replies: 21
Views: 3,131
|
Forum: General Registry Discussion
11-25-2017, 10:47 AM
|
Replies: 10
Views: 1,620
Re: Update on my DSG Mach 1
Yeah. That's my experience. Had to take a beautiful set of ceramic coated longtubes and a 2 catalytic converter mid off my Mach 1 to pass smog when I brought it in from Nevada. Went with ported stock...
|
Forum: General Registry Discussion
10-05-2017, 08:06 PM
|
Replies: 31
Views: 5,762
|
Forum: General Registry Discussion
09-09-2017, 11:46 AM
|
Replies: 31
Views: 5,762
Re: My how the auto industry has changed
I have a Teksid aluminum block forged rods and pistons waiting for a blower in the shop for when 310-ish rear wheel horsepower feels too slow. So far I am satisfied with what I have.
I weighed my...
|