Forum: Engine & Drivetrain (Including trans & rear axles)
06-23-2019, 06:48 PM
|
Replies: 2
Views: 898
Re: Possible Gear Install f-up 😒
I always use a new crush sleeve. Sounds like you will need to pull it apart, install a new crush sleeve and pinion seal. The carrier needs to be out of the rear end to properly measure the bearing...
|
Forum: Power Adders
05-01-2019, 04:07 PM
|
Replies: 2
Views: 792
Re: HPP Twin Turbo Kit
Call HPP and ask. They are awesome to deal with.
CONTACT US
Office: 972-395-9844
Fax: 972-395-9952
E-mail: dustin@hppmotorsports.com
|
Forum: Engine & Drivetrain (Including trans & rear axles)
04-04-2019, 03:55 PM
|
Replies: 10
Views: 1,696
|
Forum: Brakes & Suspension
03-28-2019, 11:31 AM
|
Replies: 12
Views: 1,123
Re: MM CC plates noise
That's my bad, I did the coilover install when I did my plates. When doing coilovers, MM states you need to clearance an area on the frame rail to avoid any interference.
There will always be a...
|
Forum: Brakes & Suspension
03-28-2019, 09:07 AM
|
Replies: 12
Views: 1,123
Re: MM CC plates noise
Are the plates new? Did you properly clearance the underside of the shock tower? Retorque all of the mounting bolts and top nut. It wouldn't hurt to pull the top bearing plate and check for a...
|
Forum: Exhaust System
03-11-2019, 10:04 PM
|
Replies: 3
Views: 1,029
|
Forum: Mustangs Parts For Sale/Wanted
02-17-2019, 12:40 PM
|
Replies: 6
Views: 1,182
|
Forum: Brakes & Suspension
01-21-2019, 10:58 AM
|
Replies: 19
Views: 2,063
Re: I need a new rack and pinion, help please?!
No leaks, squeaks, rattles, firm feel, tracked true, etc. Take it for what it's worth. I have been happy with them for daily driving. My race car uses a Flaming River manual rack if that makes a...
|
Forum: Brakes & Suspension
01-19-2019, 12:32 PM
|
Replies: 19
Views: 2,063
Re: I need a new rack and pinion, help please?!
This is true but I am just speaking from own experience that they have been quality units. I have had bad experiences using remans from the likes of Autozone and O'Reilly's but the ones I have used...
|
Forum: Brakes & Suspension
01-18-2019, 07:06 PM
|
Replies: 19
Views: 2,063
|
Forum: Brakes & Suspension
01-18-2019, 04:17 PM
|
Replies: 19
Views: 2,063
Re: I need a new rack and pinion, help please?!
Have you thought about picking up a Cobra reman rack like Summit offers? https://www.summitracing.com/parts/aaz-22-2000/overview/year/2004/make/ford/model/mustang/submodel/svt-cobra
Or jump on...
|
Forum: General Registry Discussion
01-18-2019, 04:08 PM
|
Replies: 12
Views: 990
|
Forum: Engine & Drivetrain (Including trans & rear axles)
12-26-2018, 06:52 PM
|
Replies: 3
Views: 520
Re: motor value
I picked up a complete 20K mile manual Mach1 engine(forged crank) a year ago for $2500. It had everything from the throttle cable to oil pan, clutch setup, all accessories, and even the power...
|
Forum: Power Adders
12-10-2018, 06:43 PM
|
Replies: 803
Views: 559,716
Re: Eaton Swap.....
Some parts are very hard to come by like the intercooler mounting brackets, oil cooler, and good caged lower pulleys but they can be found. If not, there are alternatives to use.
Like others have...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
08-25-2018, 10:25 AM
|
Replies: 15
Views: 4,519
Re: cylinder head cooling mod
I replaced that plastic elbow with a brass one before I installed that kit on my car. There is no way I would run a plastic elbow for that piece given the difficulty of having to potentially replace...
|
Forum: Power Adders
08-22-2018, 04:29 PM
|
Replies: 226
Views: 129,451
|
Forum: Power Adders
07-31-2018, 05:52 PM
|
Replies: 226
Views: 129,451
Re: Official Whipple/KB/Eaton HP/TQ/mods thread:
No, I was using a standard Gates 8 rib belt that I was able to source quickly. I am going to the Gates RPM belt and a bigger idler to get a little more wrap on the supercharger pulley. Hopefully that...
|
Forum: Power Adders
07-28-2018, 09:25 AM
|
Replies: 226
Views: 129,451
|
Forum: Power Adders
06-04-2018, 08:16 PM
|
Replies: 803
Views: 559,716
Re: Eaton Swap.....
My 498whp Eaton swapped Mach1 engine(in a GT) with 3.73 gears was enough to beat up on my buddy's 2012 GT with a 2.3TVS and another buddy's 2.2 KB 2004 Cobra. The newer cars are nicer, ride smoother,...
|
Forum: Fluid Systems (coolant, oil, fuel)
05-01-2018, 06:21 PM
|
Replies: 4
Views: 1,841
Re: Fuel pump replacement tips
Disconnect the battery and bleed off any extra pressure by removing the fuel filler cap and from the rail via the schrader valve. Siphon or drain as much fuel from the tank as possible. You don't...
|