Forum: Exhaust System
07-06-2014, 08:34 PM
|
|
Replies: 12
Views: 1,501
|
|
Forum: Tuning & Dyno Testing/Results
05-31-2014, 08:13 PM
|
|
Replies: 37
Views: 4,084
|
|
Forum: General Registry Discussion
05-09-2014, 11:15 PM
|
|
Replies: 20
Views: 2,867
|
|
Forum: Exhaust System
04-16-2014, 08:31 PM
|
|
Replies: 29
Views: 3,158
Re: longtubes going back on.
not worth the extra imo unless you have money to blow. BBK, Mac, Pacesetter all work. Ive had BBk and Mac. Mac must run the Lethal Performance x pipe to fit properly and BBks x pipes are known to...
|
|
Forum: Brakes & Suspension
02-24-2014, 10:14 PM
|
|
Replies: 10
Views: 1,232
Re: Isos?
Its will be fine. You may hear it pop once in a while or rattle on bumps. Nothing bad though
|
|
Forum: Brakes & Suspension
02-24-2014, 10:12 PM
|
|
Replies: 6
Views: 1,126
Re: aftermarket k member
I always hold the engine up with a cinder block and proper amount of wood under the oil pan. It wont go anywhere. Here is a write up from AM on headers that also walks you through the k member....
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
02-17-2014, 09:43 PM
|
|
Replies: 5
Views: 1,809
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
01-08-2014, 07:44 PM
|
|
Replies: 5
Views: 1,113
|
|
Forum: Tuning & Dyno Testing/Results
01-07-2014, 06:12 PM
|
|
Replies: 6
Views: 1,965
|
|
Forum: Tuning & Dyno Testing/Results
01-06-2014, 09:28 PM
|
|
Replies: 6
Views: 1,965
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
01-06-2014, 09:04 PM
|
|
Replies: 16
Views: 2,553
Re: Long tubes and 3650
yea, I have Macs and have NO CLUE how people get the 3650 in and out with the headers on. I tried with the car off the ground, along with two of my buddies and NO luck. The starter housing was...
|
|
Forum: Tuning & Dyno Testing/Results
01-06-2014, 08:46 PM
|
|
Replies: 6
Views: 1,965
Anyone running nitrous with cams?
Im making 356/339 right now cammed and thinking about putting a shot on it this summer, but im not sure how it will respond with the cams. I know a bolt on car handles a 100-125 without any trouble....
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
11-02-2013, 05:37 PM
|
|
Replies: 20
Views: 2,404
Re: 01 Cobra Cam Swap
Every car must be different, after my cam swap mine had 12.5 a/f and 22* of timing and ran like a champ. It needed cleaned up but ran and drove fine
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
11-02-2013, 12:14 AM
|
|
Replies: 20
Views: 2,404
Re: 01 Cobra Cam Swap
I wouldnt recommend doing it yourself unless you have some experience and have a lot of patience. I had a good bit of trouble when I first started messing with mine.
|
|
Forum: Exhaust System
11-02-2013, 12:06 AM
|
|
Replies: 27
Views: 4,003
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
10-11-2013, 07:41 PM
|
|
Replies: 33
Views: 3,656
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
10-10-2013, 02:56 PM
|
|
Replies: 4
Views: 1,269
Re: Vibration at 95mph +
check the bolts from the drive shaft to the rear end. Mine came loose twice, now they get the loctite impact treatment
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
10-06-2013, 09:10 PM
|
|
Replies: 27
Views: 4,501
Re: valve covers
what he said.... ^ The first time sucks but its easy once you have done a couple
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
09-22-2013, 12:30 AM
|
|
Replies: 35
Views: 3,724
Re: Epic Axle thread to end all others
should be noted I had a 4.10 put in my car today, and yes, VERY happy, but the stock spider gears have chunks missing. I reused them though, I havent BROKEN anything yet. Ill see how long they last...
|
|
Forum: Body, Chassis & Interior
09-21-2013, 11:20 AM
|
|
Replies: 20
Views: 3,098
Re: Cobra wing!
Looks good, now you just need to hang your exhaust tips even! lol
|
