2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > Search Forums

Showing results 1 to 20 of 61
Search took 0.03 seconds.
Search: Posts Made By: glittle75
Forum: Power Adders 09-06-2020, 11:03 AM
Replies: 7
Views: 1,118
Posted By glittle75
Re: What size pulley & belt size for Procharger D-1SC?

4" pulley and k061098 belt should be close. Might need a BAP, but everything else you listed should be fine.
Forum: Engine & Drivetrain (Including trans & rear axles) 07-21-2020, 09:09 PM
Replies: 2
Views: 1,211
Posted By glittle75
Re: Rebuilding a 4.6L Rant. Advice from those who have done it

I sent my stuff to TKM in NC. They are up there with the likes of Pro-Line. I explained that I want everything done to be able to handle 1500hp. I only plan to make 1000 maybe.

I brought them a...
Forum: Engine & Drivetrain (Including trans & rear axles) 07-08-2020, 04:27 PM
Replies: 2
Views: 1,633
Posted By glittle75
Re: Help! Need machine shop in Texas which uses 4.6 torque plates

I imagine Texas Speed could hook it up. They work primarily in LS stuff, but they are one of the best in the country. If they couldn't do it, I can only imagine they can point you to a reputable shop.
Forum: Engine & Drivetrain (Including trans & rear axles) 07-04-2020, 11:53 AM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Thanks! I think 3500 was a good deal for a complete kit. my inbox exploded when I posted it lol.


Staying manual for now. Not fixing it until it breaks lol. I been out playing with the KB turned...
Forum: Engine & Drivetrain (Including trans & rear axles) 07-02-2020, 05:57 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

No dyno time.

Yep, posted it last night, sold today. In process of removing the blower now. I got the tune up good, and drove the car. After driving at 480-ish HP for years, making around 600 was...
Forum: Engine & Drivetrain (Including trans & rear axles) 06-24-2020, 08:12 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Tuning update, not sure if anyone cares for tuning stuff, but here it is anyway.

So the first table that needs to be adjusted is Target Air Fuel Ratio. This table will command all the fueling and...
Forum: Engine & Drivetrain (Including trans & rear axles) 06-21-2020, 10:05 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Sounds good! As soon as I can get some 1320 time there will be videos. Was wet this weekend, hopefully next weekend.
Forum: Engine & Drivetrain (Including trans & rear axles) 06-20-2020, 10:23 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Small updates, car runs and drives great. Tuning has been fairly easy with the Holley software. I have A/F tables, Fuel tables and spark tables all dialed in.

After a few 'spirited' highway...
Forum: Engine & Drivetrain (Including trans & rear axles) 06-08-2020, 10:29 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Thanks!

New harness is in, it runs and idles. Messed with it for a while and could not figure out why it didn’t want to hot start. Turns out the alternator is dead. New one is on the way and we...
Forum: Engine & Drivetrain (Including trans & rear axles) 06-07-2020, 05:24 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

All the factory wiring that is no longer used. I plan to snip all the connectors off and save them in a jar just in case. I can always add wire. All the wiring will be scrapped. ...
Forum: Engine & Drivetrain (Including trans & rear axles) 06-07-2020, 05:23 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Alright, well went through some pains with the Holley EFI setup.
I ordered a Terminator X kit. Also the USB-CAN harness and a 3 bar MAP sensor. 3 bar gives me the ability to go up to 30psi of...
Forum: Engine & Drivetrain (Including trans & rear axles) 05-12-2020, 07:53 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Break in complete, runs and drives great with no issues. Loving the McLeod clutch after getting used to it. Very smooth and light for a unit that can handle 700hp.

After having some difficulty...
Forum: Engine & Drivetrain (Including trans & rear axles) 05-03-2020, 09:03 AM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Thanks!

Well, shes alive. Had the starter go bad for some reason (my luck) and the water pump seal got pinched on install. After changing both of those the tuner was able to get it running and...
Forum: Engine & Drivetrain (Including trans & rear axles) 05-03-2020, 08:56 AM
Replies: 9
Views: 1,075
Posted By glittle75
Re: NGK TR6 Iridium Spark Plugs

TR6 are the gold standard for mildly boosted applications. Any tuner worth their salt will suggest them. Gap for them is usually around .032" - .035" for 93 and .025" - .030" for E85.
Forum: Engine & Drivetrain (Including trans & rear axles) 04-25-2020, 11:14 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Thanks! That is the plan, at least 6 feet behind me lol!
Forum: Engine & Drivetrain (Including trans & rear axles) 04-25-2020, 06:47 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Got the regulator installed. Not a huge fan of this setup. It's huge and the FRPS mount is not the best. But it's what we got for now until I get some new rails.
...
Forum: Engine & Drivetrain (Including trans & rear axles) 04-25-2020, 06:45 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

Got a bit behind on posting. I was trying to get the car done so I could drop it off to the tuner this week.
Engine and trans going in. Was a huge PITA with the bigger pan. Had to drop it in just...
Forum: Engine & Drivetrain (Including trans & rear axles) 04-20-2020, 08:48 PM
Replies: 5
Views: 547
Posted By glittle75
Re: Tensioner bolt length?

Caliper set to MM

Free length (75.71mm)
http://www.mach1registry.org/forums/picture.php?albumid=324&pictureid=1731

Usable length from washer to end of threads (61mm)...
Forum: Engine & Drivetrain (Including trans & rear axles) 04-19-2020, 11:04 PM
Replies: 5
Views: 547
Posted By glittle75
Re: Tensioner bolt length?

If you still need, I can go measure the bolt. I have everything apart right now anyway.
Forum: Engine & Drivetrain (Including trans & rear axles) 04-11-2020, 09:05 PM
Replies: 48
Views: 4,528
Posted By glittle75
Re: Engine build for all the boost!

After that, I was able to install the cams and begin the degree process. These cams call for a 110 Intake Centerline, and 118 Exhaust Centerline. I was able to get them both within half~ish a degree....
Showing results 1 to 20 of 61

 
Forum Jump

All times are GMT -4. The time now is 06:57 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<