Forum: Engine & Drivetrain (Including trans & rear axles)
03-24-2018, 10:09 PM
|
|
Replies: 12
Views: 1,754
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
03-07-2018, 11:42 AM
|
|
Replies: 12
Views: 1,754
Re: Engine Build Check List
Double checked with the machine shop, the Melling does have billet gears. Only mistake they made was on the pistons. Had some dished pistons ending up with 9.25 compression. Told him to figure some...
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
03-07-2018, 10:24 AM
|
|
Replies: 12
Views: 1,754
Re: Engine Build Check List
I'm sure they will use penetrating dyes to accomplish the same thing sense you can't actually magnaflux aluminum
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
03-07-2018, 09:45 AM
|
|
Replies: 12
Views: 1,754
Re: Engine Build Check List
We will throw an Eaton on top with about 10-12lbs of boost running E85. Cams will push us over my budget, the machine work and bottom end was even a bit more than expected. Stuff gets expensive...
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
03-07-2018, 09:29 AM
|
|
Replies: 12
Views: 1,754
Engine Build Check List
So I just got a list if goodies from the machine shop and wanted to make sure we were missing anything or have any foreseeable issues before I give them the green light.
Donner is a Teksid block...
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
02-12-2018, 05:14 PM
|
|
Replies: 0
Views: 619
Mark VIII oil pan.
Lets say I can work around the issue with the pickup tube between the Mark8 and the Mach1, would the pan 1. work, 2. clear the factory cross member and 3. be a good upgrade?
|
|
Forum: Power Adders
01-20-2018, 01:15 PM
|
|
Replies: 7
Views: 1,493
Re: IAC not reading after Eaton swap
I know I shouldn't "wig" out and you're absolutely right. It's just frustrating when you've been working toward something for 2+ years for it to all come down to something like this. I'm sure they...
|
|
Forum: Power Adders
01-20-2018, 09:56 AM
|
|
Replies: 7
Views: 1,493
|
|
Forum: Power Adders
01-20-2018, 09:55 AM
|
|
Replies: 7
Views: 1,493
Re: IAC not reading after Eaton swap
Yes we did but he said continuity was good from the IAC to the wire harness on the back driver firewall. He was going to check Monday from the firewall to the PCM. The part I don't understand is he...
|
|
Forum: Power Adders
01-20-2018, 12:10 AM
|
|
Replies: 7
Views: 1,493
IAC not reading after Eaton swap
Well finished up the swap just in time to hit the dyno date today. Had the car at the shop right at 8am after making the hour long drive (towing). Called to check on it at 3:30 today only to find out...
|
|
Forum: Power Adders
01-06-2018, 09:06 PM
|
|
Replies: 6
Views: 1,164
Re: dead spot right off idle
I'll be using a local shop, wish I had the time to trailer it to HPP but work just won't allow it right now. I spoke to them earlier in the week and they didn't seem to think it would be a problem...
|
|
Forum: Power Adders
01-04-2018, 05:49 PM
|
|
Replies: 6
Views: 1,164
Re: dead spot right off idle
stock injectors and MAF for now, just to make sure everything else was working as it should. We have 60's waiting to go in. Vehicle won't be driven until it gets a tune, it's going to take forever...
|
|
Forum: Power Adders
01-04-2018, 12:04 AM
|
|
Replies: 6
Views: 1,164
Re: dead spot right off idle
No sir, not yet, just checking to make sure we didn't have any leaks. We were
also checking to make sure we had decent throttle response and to make sure the mechanics of the throttle was working...
|
|
Forum: Power Adders
01-03-2018, 11:24 PM
|
|
Replies: 6
Views: 1,164
dead spot right off idle
We just finished up an eaton swap and worked most of the bugs out. However, we have a slight dead spot right off idle where the car bogs for just a split second. Is this something we need to worry...
|
|
Forum: Fluid Systems (coolant, oil, fuel)
01-02-2018, 09:30 AM
|
|
Replies: 1
Views: 940
|
|
Forum: Fluid Systems (coolant, oil, fuel)
12-31-2017, 12:55 PM
|
|
Replies: 1
Views: 940
wont start after fuel pump wire upgrade
So we are in the process of doing an eaton swap on the mach. Fired it up for a second the other day and realized we had a leak at the oil cooler (wrong gasket). Got it changed out and had time to do...
|
|
Forum: Fluid Systems (coolant, oil, fuel)
04-15-2016, 05:09 PM
|
|
Replies: 3
Views: 663
Re: upgrades for E85
Thanks for the info TK, I don't plan on pushing more than 450 on the stock block. I was just thinking running E85 would buy me a little more insurance. :)
I might check into other pumps that are...
|
|
Forum: Fluid Systems (coolant, oil, fuel)
04-14-2016, 12:22 PM
|
|
Replies: 3
Views: 663
upgrades for E85
Did some looking and didn't find much that was specific to our fuel system. I'm doing an Eton swap and want to upgrade the fuel system to run E85. I already figure I'll need a better pump and...
|
|
Forum: Mustangs Parts For Sale/Wanted
09-27-2011, 09:14 AM
|
|
Replies: 15
Views: 910
|
|
Forum: Mustangs Parts For Sale/Wanted
09-19-2011, 08:06 AM
|
|
Replies: 15
Views: 910
|
