Forum: US-MidWest Region
07-17-2008, 10:35 AM
|
Replies: 4
Views: 619
|
Forum: Surveys & POLLS
01-30-2008, 03:48 PM
|
Replies: 158
Views: 8,559
Re: New or Used Mach 1
I bought mine new in March of 2004. I ended up paying around 23K for it after my trade in and haggling. I also was able to get the 0% financing. :) It has about 18K miles on it now and I don't...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
06-10-2005, 10:51 AM
|
Replies: 33
Views: 2,434
Re: New Heads for Ticking Noise-Part#s inside...
My bad, I should have been more specific. This is only true in a local area radius, like the greater KC area for example. They do this to help maintain customer retention among local dealers of the...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
06-10-2005, 08:59 AM
|
Replies: 33
Views: 2,434
Re: New Heads for Ticking Noise-Part#s inside...
Just to let you know, you are very wrong about that. Warranty work makes up a very small percentage of service revenue. Also, a warranty repair pays LESS than a CP repair. The warranty labor rate...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
06-09-2005, 02:24 PM
|
Replies: 33
Views: 2,434
Re: New Heads for Ticking Noise-Part#s inside...
OK, first of all, who the f#@k said anything about bribery? Third World country? WTF are you talking about? The point is, if you didn't buy your car from the Ford dealer you want to take it to,...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
06-09-2005, 09:10 AM
|
Replies: 33
Views: 2,434
Re: New Heads for Ticking Noise-Part#s inside...
Usually a big volume dealer will be more likely to help. You might try talking to Extreme Ford in Overland Park. I think they sell a lot of specialty Mustangs, so there service dept. should be...
|
Forum: Technical Q&A. HOW TO's, TSB's & Warranty Items
06-08-2005, 05:34 PM
|
Replies: 21
Views: 1,368
|
Forum: Engine & Drivetrain (Including trans & rear axles)
06-08-2005, 04:12 PM
|
Replies: 33
Views: 2,434
Re: New Heads for Ticking Noise-Part#s inside...
I got the same response from the dealer I purchased my car from. They gave me the whole " I don't know what your talking about" bit. Unfortunately, you're going to run into that at most domestic...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
06-07-2005, 11:49 AM
|
Replies: 33
Views: 2,434
New Heads for Ticking Noise-Part#s inside...
Just in case you all have not seen this yet, here are the part numbers for the new redesigned heads. I've already got the OK from my dealer to put them on my car, although I only have a very slight...
|
Forum: Engine & Drivetrain (Including trans & rear axles)
05-25-2005, 12:33 PM
|
Replies: 47
Views: 3,684
Re: Those with MAF screens removed
I have a JLT CAI with the MAF screen removed. I also have a PHP spacer, Magnaflow O/R X-pipe, and Magnaflow catback all working in harmony with my (tuned on the dyno) Superchip. It purrs like a...
|
Forum: Tuning & Dyno Testing/Results
05-19-2005, 03:11 PM
|
Replies: 15
Views: 1,155
|
Forum: Tuning & Dyno Testing/Results
05-19-2005, 08:32 AM
|
Replies: 21
Views: 939
Re: HELP! Problem with current chip Burn
The predator tune is crap. I USED to use the predator until I tested it on the dyno. WITH the predator tune, the car was running WAY lean. We put back in the stock tune and it made MORE power. ...
|
Forum: Tuning & Dyno Testing/Results
05-18-2005, 07:00 PM
|
Replies: 70
Views: 6,312
|
Forum: Tuning & Dyno Testing/Results
05-18-2005, 03:57 PM
|
Replies: 21
Views: 939
Re: HELP! Problem with current chip Burn
Hello,
The A/F numbers you were showing are too low. They should be around 13/1 on a Mach 1. The problem you're having is caused by the factory knock sensors. You're getting detonation under...
|
Forum: Tuning & Dyno Testing/Results
05-18-2005, 09:41 AM
|
Replies: 28
Views: 22,314
Re: Do gears affect Dyno Numbers?
blueautomach,
I just happened to see your problem while reading this thread. They were able to solve the loss of power above 4000 RPM on my car by limiting the knock sensors ability to pull so...
|
Forum: Tuning & Dyno Testing/Results
05-17-2005, 07:11 PM
|
Replies: 15
Views: 1,155
|
Forum: Tuning & Dyno Testing/Results
05-17-2005, 07:08 PM
|
Replies: 15
Views: 1,155
|
Forum: Tuning & Dyno Testing/Results
05-11-2005, 04:25 PM
|
Replies: 15
Views: 1,155
|
Forum: Tuning & Dyno Testing/Results
05-11-2005, 03:50 PM
|
Replies: 2
Views: 563
Re: knock sensors
It's not a good idea to turn off the knock sensors. I think the best approach is to limit how much timing they can pull. That's what we did on my car. Worked out great. Good luck.
|
Forum: Ebay Watch - Mach 1 stuff on eBay
03-07-2005, 10:27 AM
|
Replies: 0
Views: 629
|