2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > Search Forums

Showing results 1 to 20 of 200
Search took 0.10 seconds.
Search: Posts Made By: 04Mach1FTW
Forum: Exhaust System 07-06-2014, 08:34 PM
Replies: 12
Views: 1,491
Posted By 04Mach1FTW
Re: What Headers Give Good Gains and Don't Block Access to Transmission?

They say you can with Mac, I have never been successful in the driveway though
Forum: Tuning & Dyno Testing/Results 05-31-2014, 08:13 PM
Replies: 37
Views: 4,061
Posted By 04Mach1FTW
Re: Well, got back from the dyno....

It needs some better bump sticks
Forum: General Registry Discussion 05-09-2014, 11:15 PM
Replies: 20
Views: 2,857
Posted By 04Mach1FTW
Forum: Exhaust System 04-16-2014, 08:31 PM
Replies: 29
Views: 3,131
Posted By 04Mach1FTW
Re: longtubes going back on.

not worth the extra imo unless you have money to blow. BBK, Mac, Pacesetter all work. Ive had BBk and Mac. Mac must run the Lethal Performance x pipe to fit properly and BBks x pipes are known to...
Forum: Brakes & Suspension 02-24-2014, 10:14 PM
Replies: 10
Views: 1,223
Posted By 04Mach1FTW
Re: Isos?

Its will be fine. You may hear it pop once in a while or rattle on bumps. Nothing bad though
Forum: Brakes & Suspension 02-24-2014, 10:12 PM
Replies: 6
Views: 1,115
Posted By 04Mach1FTW
Re: aftermarket k member

I always hold the engine up with a cinder block and proper amount of wood under the oil pan. It wont go anywhere. Here is a write up from AM on headers that also walks you through the k member....
Forum: Engine & Drivetrain (Including trans & rear axles) 02-17-2014, 09:43 PM
Replies: 5
Views: 1,797
Posted By 04Mach1FTW
Re: tr-3650 noise

sounds like you got a bad tob
Forum: Engine & Drivetrain (Including trans & rear axles) 01-08-2014, 07:44 PM
Replies: 5
Views: 1,100
Posted By 04Mach1FTW
Re: New clutch cable question

better yet, MOST people using aftermarket quadrant and adjuster have best luck with a new OEM cable.
Forum: Tuning & Dyno Testing/Results 01-07-2014, 06:12 PM
Replies: 6
Views: 1,945
Posted By 04Mach1FTW
Re: Anyone running nitrous with cams?

Dayton OH. I bought a transmission ill be having built Todd ;) eventually...
Forum: Tuning & Dyno Testing/Results 01-06-2014, 09:28 PM
Replies: 6
Views: 1,945
Posted By 04Mach1FTW
Re: Anyone running nitrous with cams?

Should be noted they are not nitrous cams and were degreed for n/a
Forum: Engine & Drivetrain (Including trans & rear axles) 01-06-2014, 09:04 PM
Replies: 16
Views: 2,522
Posted By 04Mach1FTW
Re: Long tubes and 3650

yea, I have Macs and have NO CLUE how people get the 3650 in and out with the headers on. I tried with the car off the ground, along with two of my buddies and NO luck. The starter housing was...
Forum: Tuning & Dyno Testing/Results 01-06-2014, 08:46 PM
Replies: 6
Views: 1,945
Posted By 04Mach1FTW
Anyone running nitrous with cams?

Im making 356/339 right now cammed and thinking about putting a shot on it this summer, but im not sure how it will respond with the cams. I know a bolt on car handles a 100-125 without any trouble....
Forum: Engine & Drivetrain (Including trans & rear axles) 11-02-2013, 05:37 PM
Replies: 20
Views: 2,340
Posted By 04Mach1FTW
Re: 01 Cobra Cam Swap

Every car must be different, after my cam swap mine had 12.5 a/f and 22* of timing and ran like a champ. It needed cleaned up but ran and drove fine
Forum: Engine & Drivetrain (Including trans & rear axles) 11-02-2013, 12:14 AM
Replies: 20
Views: 2,340
Posted By 04Mach1FTW
Re: 01 Cobra Cam Swap

I wouldnt recommend doing it yourself unless you have some experience and have a lot of patience. I had a good bit of trouble when I first started messing with mine.
Forum: Exhaust System 11-02-2013, 12:06 AM
Replies: 27
Views: 3,973
Posted By 04Mach1FTW
Re: lets hear those cammed machs

custom grinds, stock lift, stock springs/retainers

http://www.youtube.com/watch?v=QAUDQZbfRD4
Forum: Engine & Drivetrain (Including trans & rear axles) 10-11-2013, 07:41 PM
Replies: 33
Views: 3,577
Posted By 04Mach1FTW
Re: Big N/A Mod Motors

awesome. They should raffle off the winning motor :)
Forum: Engine & Drivetrain (Including trans & rear axles) 10-10-2013, 02:56 PM
Replies: 4
Views: 1,262
Posted By 04Mach1FTW
Re: Vibration at 95mph +

check the bolts from the drive shaft to the rear end. Mine came loose twice, now they get the loctite impact treatment
Forum: Engine & Drivetrain (Including trans & rear axles) 10-06-2013, 09:10 PM
Replies: 27
Views: 4,414
Posted By 04Mach1FTW
Re: valve covers

what he said.... ^ The first time sucks but its easy once you have done a couple
Forum: Engine & Drivetrain (Including trans & rear axles) 09-22-2013, 12:30 AM
Replies: 35
Views: 3,708
Posted By 04Mach1FTW
Re: Epic Axle thread to end all others

should be noted I had a 4.10 put in my car today, and yes, VERY happy, but the stock spider gears have chunks missing. I reused them though, I havent BROKEN anything yet. Ill see how long they last...
Forum: Body, Chassis & Interior 09-21-2013, 11:20 AM
Replies: 20
Views: 3,063
Posted By 04Mach1FTW
Re: Cobra wing!

Looks good, now you just need to hang your exhaust tips even! lol
Showing results 1 to 20 of 200

 
Forum Jump

All times are GMT -4. The time now is 06:21 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<