2003-04 Mach 1 Registry Owners Club  


Go Back   2003-04 Mach 1 Registry Owners Club > Search Forums
Reload this Page Search Results
Photo Gallery $ Donations $ Register FAQ Community Calendar Today's Posts Search

Page 1 of 8 1 2345678
Showing results 1 to 20 of 147
Search took 0.15 seconds. Search: Posts Made By: Mach1 Of A Kind
Forum: Engine & Drivetrain (Including trans & rear axles) 05-14-2012, 11:14 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

well it took some time but finally got it tuned. Had some idle and stalling issues but think we got it now. Here are the numbers;

Mustang dyno;

Best pull without cams 332 hp and 332 tq at 6448...
Forum: Engine & Drivetrain (Including trans & rear axles) 03-30-2012, 05:56 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

I haven't made the apointment yet. Just got more stupid snow up here :(
So its going to have to wait for a bit.
Forum: Engine & Drivetrain (Including trans & rear axles) 03-28-2012, 02:54 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Just have to get it tuned again and see what the gain will be.
Before numbers are.
I put down 332HP and 335TQ on motor.
I put down 420HP and 440TQ on nitrous
Mustang dyno.

Thanks to everyone...
Forum: Engine & Drivetrain (Including trans & rear axles) 03-28-2012, 02:30 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Hear is the sound video.

http://www.youtube.com/watch?v=k8jrSUK1j-0
Forum: Engine & Drivetrain (Including trans & rear axles) 03-28-2012, 01:31 AM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Well its back together and running good. sounds good too.
Hear are some pics.

http://i304.photobucket.com/albums/nn195/HDTURNR/Cam%20swap/IMG_0452.jpg

...
Forum: Engine & Drivetrain (Including trans & rear axles) 03-25-2012, 09:29 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Are the two valve tensioners the same as the four valve ones? Do I get the racheting ones?
Forum: Engine & Drivetrain (Including trans & rear axles) 03-25-2012, 07:57 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

The primary tentioners are plastic. I guess I need to replace them then. Where do I get them from? Ford dealer? Dam I guess I'm at a stand still. :(
Forum: Engine & Drivetrain (Including trans & rear axles) 03-25-2012, 06:43 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Cool thanks. Its going back together.

One more question though. The main chain adjusters have a O ring type seal that is no good now. Can I use a little cylicone for it or just install it with a...
Forum: Engine & Drivetrain (Including trans & rear axles) 03-25-2012, 05:41 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Ok I installed the gears at 4 deg and re-checked the degree and here is the results.

Right intake 72/148 = 220= 110 LSA
Right ex is same at 114 LSA

Left intake 72/146 = 218= 109 LSA
Left ex...
Forum: Engine & Drivetrain (Including trans & rear axles) 03-25-2012, 03:36 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Thanks Mach 828. I have that pdf and know how to degree them now just dont know how to make the adjustment with the cloyes gear.

So what you are saying NA SVT is that you install the gear on the...
Forum: Engine & Drivetrain (Including trans & rear axles) 03-25-2012, 01:42 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

So are you saying that you only turn the gear and not the cam but if so how does that change the timing if you are leaving the cam in the same spot?

OMG this doesn't make sense. What am I missing...
Forum: Engine & Drivetrain (Including trans & rear axles) 03-25-2012, 03:25 AM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Ok well I just got in from the garage and I'm lost. Yes I used the center line method no solid lifter though. I know on the stock cam readings for the drivers side were done wrong. I installed the...
Forum: Engine & Drivetrain (Including trans & rear axles) 03-24-2012, 08:03 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

When installing the adjustable gears do you put them at stock position first and check LSA. Then if its not right take it apart and re-set the gears. Does the adjustable gear go on the intake cams?
Forum: Engine & Drivetrain (Including trans & rear axles) 03-24-2012, 07:58 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Ok got the cams and gears. Started tearing it down....Ya left valve cover is a pain in the you know what. Thought I would check the LSA on the stock cams. This is what I got.

right intake cam...
Forum: Engine & Drivetrain (Including trans & rear axles) 03-13-2012, 04:19 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Ok cool. Thanks. Parts are ordered from summit. Got the cams for $1089.00 Can't wait should be hear next week :)
Forum: Engine & Drivetrain (Including trans & rear axles) 03-13-2012, 02:53 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Don't I need the big adjustable gears as well. Please advise.
Forum: Engine & Drivetrain (Including trans & rear axles) 02-24-2012, 02:12 AM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

No I'm not going to replace everything. Just getting what na svt said.
Forum: Engine & Drivetrain (Including trans & rear axles) 02-23-2012, 10:33 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Anybody?
Forum: Engine & Drivetrain (Including trans & rear axles) 02-22-2012, 09:51 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

That figures lol. Guess I gotta go with 108/114-116
What would happen if I went with 106/110
Could I still use the nitrous just with no gains?
Forum: Engine & Drivetrain (Including trans & rear axles) 02-22-2012, 09:33 PM
Replies: 74
Views: 6,377
Posted By Mach1 Of A Kind
Re: Can I use the stock valve springs?

Does anyone know about this place? $300 bucks cheeper for the cams....
Showing results 1 to 20 of 147
Page 1 of 8 1 2345678

 
Forum Jump

All times are GMT -4. The time now is 02:11 PM.

Contact Us - www.Mach1Registry.Com - Archive - Privacy Statement - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com

<