Forum: Power Adders
04-26-2010, 09:28 PM
|
|
Replies: 803
Views: 574,397
Re: Eaton Swap.....
I used all the stock brackets, turn out fantastic. Just a bunch of cutting, drilling, bending and polishing.
|
|
Forum: Wheels & Tires
01-06-2010, 09:55 AM
|
|
Replies: 39
Views: 3,621
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
01-05-2010, 05:39 PM
|
|
Replies: 34
Views: 1,730
Re: Think I need a clutch?
Just a firm pull up. Should make a ratcheting noise. I assume you have a stock quadrant and cable. Did you get my PM?
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
01-05-2010, 05:16 PM
|
|
Replies: 34
Views: 1,730
Re: Think I need a clutch?
Have you tried pulling up on the clutch pedal ? The stock mach clutches have a automatic adjuster, and by pulling up on the pedal it should reset the adjustment. Just a thought, my not work for you,...
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
01-03-2010, 11:38 AM
|
|
Replies: 58
Views: 3,483
Re: Got my short-block together...and then some!!
Nice, Thanks for the reply. I'm very interested in this build. I'm about to begin a build. I have been debating whether to build the NVH block that is in the car (only 15,477 mi on it) 7000 since...
|
|
Forum: Engine & Drivetrain (Including trans & rear axles)
01-02-2010, 05:36 PM
|
|
Replies: 58
Views: 3,483
|
|
Forum: Power Adders
04-02-2009, 07:21 PM
|
|
Replies: 28
Views: 1,770
Re: Eaton Swap Guys
The steel tube on the plenum hooks up to the black vac tube that is shown in pic number 3 from the left. It goes back to the tank.
|
|
Forum: Power Adders
04-02-2009, 07:10 PM
|
|
Replies: 28
Views: 1,770
Re: Eaton Swap Guys
picture number 3 from the left, if you did a egr delete you can pretty much throw all those vac lines away. Or cut it up and use a couple small pieces.
|
|
Forum: Power Adders
04-02-2009, 07:06 PM
|
|
Replies: 28
Views: 1,770
Re: Eaton Swap Guys
A lot of people, me included just put a plug in the bottom of the lower intake and ran the large vac line from the back of the eaton over to the pcv valve on the drivers side valve cover.
|
|
Forum: Power Adders
04-02-2009, 06:56 PM
|
|
Replies: 28
Views: 1,770
|
|
Forum: Surveys & POLLS
03-05-2009, 04:25 PM
|
|
Replies: 253
Views: 36,659
Re: low mile machs
We bought our mach in April 08 with 1568 miles, Parked it in the garage end of October with 8300 miles. Did a Eaton swap while it was parked. Have driven it a few times this Spring now has 8450...
|
|
Forum: Surveys & POLLS
02-23-2009, 06:34 PM
|
|
Replies: 29
Views: 1,316
|
|
Forum: NEW Mach 1 Owner Introductions
02-21-2009, 07:21 PM
|
|
Replies: 23
Views: 574
|
|
Forum: Power Adders
02-21-2009, 07:17 PM
|
|
Replies: 7
Views: 738
|
|
Forum: Power Adders
02-21-2009, 09:51 AM
|
|
Replies: 226
Views: 133,198
|
|
Forum: Power Adders
02-14-2009, 04:28 PM
|
|
Replies: 13
Views: 1,210
Re: Cheapest way to do Eaton swap...
Nice I did the same thing over a few months and just finished my swap...I love it, even though I have'nt been able to drive it much at all yet. Still snowing alot here. Have you done the swap?
|
|
Forum: Power Adders
02-14-2009, 04:13 PM
|
|
Replies: 13
Views: 1,210
|
|
Forum: Power Adders
02-14-2009, 03:48 PM
|
|
Replies: 13
Views: 1,210
Re: Cheapest way to do Eaton swap...
You won't find any terminators in junkyards with any good parts on them. Ebay is good or find someone going turbo. I would plan at least a week....unless you have someone helping you that has done...
|
|
Forum: Power Adders
02-11-2009, 08:33 PM
|
|
Replies: 803
Views: 574,397
Re: Eaton Swap.....
Hi Archie, I havent got to drive it much. We trailered it to Denver to my tuner and just got home from trailering it back. Crapy weather here, not able to drive it yet. Just a little down in Denver...
|
|
Forum: Power Adders
02-11-2009, 08:23 PM
|
|
Replies: 803
Views: 574,397
Re: Eaton Swap.....
It's a unported Eaton with a 3.10 upper, stock lower, Billetflow idler/snubber pulley, C&L Intake, K&N conical 10" Filter, EGR Delete. Everything else is just as the list on here goes.
|
