Re: What to do to get 300 rwhp on a Mach 1
 

I put mine on a dyno a few weeks ago and it put down 290hp and 315tq. I have a SCT handheld base tune, 4.10's, JLT ram air intake, and a Bassani catback. I just got some BBK long tubes and plan to order a PHP intake spacer soon so once I get those put on I'm hoping to pass 300hp. Oh and my car also has 103k on the engine as well.

Re: What to do to get 300 rwhp on a Mach 1
 

I made 302/306 with jlt intake,bbk catless x and magnapacks. No tune. Also have 4:10 gears

Palmer your number sound right. Bet you will hit 302 after the long tubes.

Sent with a shot of DROID go fast

Re: What to do to get 300 rwhp on a Mach 1
 

Found my first dyno sheet! Almost 300whp, Xpipe, weld in mufflers (hooker), jlt intake, no tune

http://i1064.photobucket.com/albums/...4/IMAG0477.jpg

Re: What to do to get 300 rwhp on a Mach 1
 

Thanks I was starting to feel a little bad looking at some of these other numbers.

Re: What to do to get 300 rwhp on a Mach 1
 

I've got an 04 mach manual with 100K miles. It has JLT RAI, Stock 3.55 gears, MAC off road H-Pipe, flowmaster weld in mufflers and Bama Tunes, anyone know where about I would be in terms of SAE numbers?

Re: What to do to get 300 rwhp on a Mach 1
 

My 04 has BBK long tubes only right now, when I get back from asscrackistan it's getting a JLT Next gen CAI, BBK 65mm TB, cobra 39lb injectors, 40,000V coil packs, exeddy flywheel, and mach 500 clutch, magnaflow cat back, and a complete 31 spline conversion. And yes its getting DR's to. I'm putting 3:73's in because its a daily driver, it will get 4:30's or 56's in the future when it's just a weekend racer/driver. I'm looking forward to seeing what my dyno numbers will be. And sugestions on tuners in Texas, and on handheld like diablo SCT or bama?

Re: What to do to get 300 rwhp on a Mach 1
 

The injectors, coils, TB and CAI will add no power.

Re: What to do to get 300 rwhp on a Mach 1
 

Finally went to a dyno day.

322.5 HP and 349.5 T

Mods are: Magna flow catted x-pipe and cat-back with magnapacks. JLT air intake pipe, Spectre air filter (the biggest one I could find that fits).

DiabloSport Predator tune.

Re: What to do to get 300 rwhp on a Mach 1
 

That's a pretty generous dyno.

Re: What to do to get 300 rwhp on a Mach 1
 

It's from a 2016 DynoCom 6000. Not sure what you mean by generous. Is there something wrong with a DynoCom dyno?

Re: What to do to get 300 rwhp on a Mach 1
 

I'm just saying with those simple mods your dyno numbers should be right around 300rwhp/310rwtq. If you had long tube headers I could see the 322rwhp. The 349rwtq is whacky.

Re: What to do to get 300 rwhp on a Mach 1
 

You see the dyno report right?

It was the best of 4 pulls. HP varied from 320, 318, 312. T stayed above 340. The best was the second pull.

Perhaps you're mistaken. I've noticed folks are quick to right off the Predator, and admit they're a pain to work with, but the results speak for themselves. I was actually hoping for better HP, but it's just a number, the car is quick.

Re: What to do to get 300 rwhp on a Mach 1
 

A bone stock Mach is 280rwhp at best in stock form. You're not gonna get over 40rwhp from a midpipe, catback and tune. You can get a dyno to spit out whatever numbers you want depending on how it's setup. It's just whack numbers, but whatever.

Re: What to do to get 300 rwhp on a Mach 1
 

Thunder is speaking the truth!

FWIW my stock Mach with flow masters in place of the stock muffler only put down 268 on a mustang dyno

Re: What to do to get 300 rwhp on a Mach 1
 

Exactly. Mine was 274whp with a drop-in air filter and Flowmasters. That dyno operator is out to make friends. :23:

Re: What to do to get 300 rwhp on a Mach 1
 

Very happy dyno. That or it was done with a negative DA and the numbers were not corrected. Put it on a dynojet with an SAE correction if you want the real numbers.

Re: What to do to get 300 rwhp on a Mach 1
 

I have jlt rai slp longtubes catted xpipe and loudmouth catback, frpp 3.73 gears bbk tb with sct x4 tunes by gear heads and got 321 rwhp 347 rwtq.

Re: What to do to get 300 rwhp on a Mach 1
 

I know butt dynos lie, but ain't noooooo way my intake/full exhaust car is 320+whp lol. My catback 6.0 GTO made SAE 340-345whp on 3 back to back runs, and other than the violent 1st gear with 4.10's I have I still don't think it would pull on the GTO. Maybe it's the illusion from the power falling off over 6k rpm's, but I'm honestly a bit disappointed. I figure the only way to solve that without getting spending serious money is a ported intake/98 Cobra cams.

Re: What to do to get 300 rwhp on a Mach 1
 

I haven't put my Mach on a dyno yet.

But the 2V GT cars almost always made 220-225 stock. Mine with CAI, TB, underdrive pullies, exhaust, and 3.73 gears made 260 on a Mustang brand dyno which is notorious for reading lower than other brands. That's a nearly 40 horsepower increase with very simple bolt-ons and a tune.

I have been told by the same dyno operator that Mach 1 cars generally are very well tuned from the factory and don't pick up the same kind of numbers as the GT cars do from bolt-ons and tunes. He said the biggest N/A gains he's ever seen in his shop was a guy who did very specific cams and got 50 HP on the dyno from those.