Re: What to do to get 300 rwhp on a Mach 1
 

Does everyone put down SAE or STD numbers?
I have PSR from NAZ, 3/8" spacer, C&L intake, 90MM maf, Accufab T/B, Hooker 1 5/8" longtubes, O/R X pipe, Magnaflow Exhaust and with a custom dyno tune i out down 299rwhp and 308ft/lbs.
The really question is with 300rwhp how good are you 1/4 mile times?
I ran 12.66@108 with 17" MT Et Streets!

Re: What to do to get 300 rwhp on a Mach 1
 

Those numbers are def. too low for what you have. My numbers are SAE corrected and over 300 with way less mods. Your track time sounds alittle slow for what you have as well, the trap speed seems like it should be alittle higher. You should be making 320-330 whp...

Re: What to do to get 300 rwhp on a Mach 1
 

On that 12.66 run, i was granny shifting and was really slow from 2nd to 3rd. Next time out i'll be slapping on my prostars skinnys with my 26x10 slicks. Plus the 4.30's probably hurt my RWHP number.

Re: What to do to get 300 rwhp on a Mach 1
 

Dyno tuned, made 285 last summer. Since them i installed a Magnaflow c/b and a PSR. A Local tuner around Halifax just got the SCT program, so i'm gonna check him out. Runs good and all, maybe a few more ponies still on the table.

Re: What to do to get 300 rwhp on a Mach 1
 

5 Speed 2004. Car has BBK Long tubes , O/R H pipe, Mac catback, c&l inlet pipe, mobil 1 10w30. Made 300 whp and 322 wtq on a dynojet. Car didn't want to take any timing that day, was hoping for higher #'s with my LT's

Re: What to do to get 300 rwhp on a Mach 1
 

mods in sig + 4.10's = 306.9whp/332.6wtq

Re: What to do to get 300 rwhp on a Mach 1
 

Looks like your dyno is a little stingey on rwhp numbers.

Re: What to do to get 300 rwhp on a Mach 1
 

The numbers are far from accurate..those are mustang dyno numbers so they are actually very gracious!

Re: What to do to get 300 rwhp on a Mach 1
 

That explains it. I'd say your tq is spot on though.

Re: What to do to get 300 rwhp on a Mach 1
 

Just run it on a non-loaded dyno and you will be golden.

Re: What to do to get 300 rwhp on a Mach 1
 

im getting 350 on my gt with running race fuel and tune with 430 gears but i have drag radials too.

Re: What to do to get 300 rwhp on a Mach 1
 

You only have 21* from 4000+ ? :12:

And a lot of people in this thread are not posting SAE. Shame on you!

Re: What to do to get 300 rwhp on a Mach 1
 

mods?

Re: What to do to get 300 rwhp on a Mach 1
 

I managed 317 HP and 327 TQ with Long tubes, pro chamber, MAC cat back, Roy's ported intake and spacer, C&L CAI, 3.90's and a N/A tune from Mustang Magic.

Re: What to do to get 300 rwhp on a Mach 1
 

Any 1/4 mile passes?

Re: What to do to get 300 rwhp on a Mach 1
 

12.6 @ 108 with SHOT drag radials. Horrible 60' 2.2 sec.

Re: What to do to get 300 rwhp on a Mach 1
 

What DA and elevation? GOOD E.T!

Re: What to do to get 300 rwhp on a Mach 1
 

Elevation was sea level I think. Island drag way in NJ. DA????

Re: What to do to get 300 rwhp on a Mach 1
 

his imagination :23:

Re: What to do to get 300 rwhp on a Mach 1
 

Density Altitude, it affects your time some. Not a big deal.

Re: What to do to get 300 rwhp on a Mach 1
 

Yeah I don't really pay attention to those things. I just go out there and try to better myself. I SHOULD probably pay attention to the little stuff though.....

Re: What to do to get 300 rwhp on a Mach 1
 

i just want him to tell me. :23::12::23:

Re: What to do to get 300 rwhp on a Mach 1
 

It's all good man.